Search Documents

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By F. W. Gray

Summarized Foreword This paper is one of a series arranged by Institute Divisional Committees for the Fiftieth Anniversary Meeting, reviewing the experience of the major mining and metallurgical industries during the life of the Institute. The viewpoint is national and broadly technical. Geology is stressed on a continental scale without regard for provincial boundaries. The boundary between Canada and the United States is, however, so decisive a factor in our coal-mining economics and our political evolution that mention of its implications cannot be avoided. The Laurentian Shield in Canada makes the occurrence of coal deposits a geological impossibility between the St. Lawrence Lowlands and the Great Plains. All but five per cent of Canadian coal resources occur west of Winnipeg. The utilization of this ninety-five per cent of our coal wealth has to date been a consequence of transcontinental railways' development, and the small fuel needs of thinly populated wheat farming and cattle-raising territory, in what- to judge from the development of mixed farming and greater population density of Manitoba- is merely an initial stage of agricultural intensification and accordant population growth. There is no useful purpose in measuring coal resource against consumption rate in the West as a whole, because the resource is but partially known, and it is difficult to believe that industrialism based upon coal utilization is in any but its infant stage of growth. Canada west of Winnipeg possesses, moreover resources of petroleum and natural gas, which, together with the power-potential in the long watershed of the eastern slope of the Rocky mountains, give to population centres such as Calgary and Edmonton a choice of energy resources that is almost an embarrass des riches.

Jan 1, 1948

By T. Marolt, J. Likar, E. Grøv, J. Žarn

"Underground structures are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, not at least nuclear facilities. When the wider area is subject to earthquake activity, underground constructions should be analyzed on seismic and static loading. Observations showed that the underground structures have significantly less seismic risk than surface structures. Available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. Simulation of earthquake loading on underground structures, in the present paper is given the various aspects of analyzing the potential damage and instability of underground facilities. INTRODUCTIONThe development of methods and computing resources used for para-seismic engineering has finetuned the evaluation of the seismic strength of buildings and equipment. Reinforcements may therefore be decided, not simply on the basis of a reassessment of the hazard, which constitutes input data for the calculation of structures and equipment, but also on the basis of developments in para-seismic engineering. Underground facilities are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, material storage, and sewage and water transport and not at least nuclear facilities. Although in the past showed that the underground structures are significantly less seismic risk than on the surface, the professional researches and their results are accessible. Seismic resistance of underground structures is analyzed from several aspects. The currently available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. For better interpretation of earthquake loading on underground structures, are given below the various aspects of analyzing the potential damage and instability of underground facilities in rock. One of the early studies which covered this are of investigation were prepared by Dowding and Rozen (1978). They grouped damages due to earthquakes in underground structures into three main categories:- damage from ground shaking- damage from fault dislocation- damage by earthquake-induced ground failures (e.g. liquefaction and landslides)."

Jan 1, 2015

By M. Fan, H. E. Wyslouzil, J. Kohmeunch

Eriez HydroFloat(TM) separators and Canadian Process Technologies (CPT) flotation columns have been developed to overcome the limitations of traditional flotation cells in recovering coarse and fine particles, respectively. The flotation column can effectively separate 30-5 µm phosphate. Several industrial-scale HydroFloat separators have been installed in phosphate and potash beneficiation plants. Industrial-scale ultra-coarse (+850 µm) phosphate separation results suggest that a more-than 40% BonePhosphate- of-Lime (BPL) recovery increase and a 37% collector consumption reduction can be achieved. The paper describes the applications of Eriez HydroFloat separators to coarse particle separation and the CPT flotation column to fine/ultrafine particle flotation.

Jan 1, 2009

By A. Shakoor, T. P. Gautam

The long-term slaking behavior of clay-bearing rocks in the field can be quite different than the short-term slaking behavior in the laboratory. To assess this difference, 12 replicate samples of each of 20 clay-bearing rocks, including 5 claystones, 5 mudstones, 5 siltstones, and 5 shales, were exposed to natural climatic conditions for 12 months. After each month of exposure, one replicate sample of each rock was removed from natural exposure and its grain size distribution was determined. Disintegration ratio (DR), defined as the ratio of the area under the grain size distribution curve of the slaked material for a given rock to the total area encompassing all grain size distribution curves of the tested samples, was used to quantify the amount of disintegration under natural climatic conditions. DR values of naturally exposed samples were then compared with the corresponding values of second-cycle slake durability index (Id2) determined in the laboratory. The relationship between Id2 and DR after, 1 month of exposure, exhibits an R2 value of 0.65 but the relationship deteriorates when DR values for 6 and 12 months of exposure are used, with R2 values of 0.63 and 0.25, respectively. However, when DR values for laboratory samples, computed from grain size distributions of slaked material after second cycle, are compared with DR values of naturally exposed samples for the three periods of exposure, the relationship improves with the corresponding R2 values being 0.61, 0.71, and 0.41. These results suggest that DR may be a better parameter for assessing the long-term disintegration behavior of clay-bearing rocks than Id2.

Jan 1, 2015

By Ali Montaser

Hauling trucks are important part of equipment fleets for large earthmoving operations such as those encountered in dams and highway construction projects. This paper presents an automated methodology for tracking and estimating productivity of hauling trucks fleet operations in near-real-time. Recent advancement in automated site data acquisition technologies made their use in tracking and monitoring of construction operations feasible. However, these technologies fail to track hauling truck fleets due to the change in the cut and fill locations from one cycle to another; making tracking and progress reporting difficult and inaccurate. In addition, there is very little work done utilizing data sensed directly from equipment, for example sensing when truck dumping bed is raised during the dumping process. The technologies deployed in the developed method are Radio Frequency Identification (RFID) and equipment control sensors. Low cost passive RFID tags are attached to hauling trucks and fixed RFID readers are attached to loaders or excavators. The read range of the used RFID tag is centimeters, to be activated only when a loader with an attached RFID reader is loading a truck. On the other hand, control sensor is connected to the truck control system and operated by the motion of its movable bed. The function of control sensors is to record the signal time when the truck operator gives order to the truck control system to raise or lower truck bed. The captured data is then transferred wirelessly from the RFID reader and control sensor to a computer housed in one of the temporary offices onsite and subsequently to the main server in the contractor?s head office. Fusing the data captured from RFID reader and control sensor is used to identify loading, travel, dumping and return time that constitute the hauling truck cycle time. The collected data is analyzed and processed automatically, without human intervention, to calculate the productivity of the hauling truck and to report it directly to onsite personnel. Relational database is developed to support the implementation of the proposed method. The developed database is used to process the data captured by the RFID and the control sensor to calculate the productivity achieved in cutfill operations in near-real-time. The developed methodology is expected to facilitate early detection of discrepancies between actual and planned performances.

Aug 1, 2013

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By R. E. Eyre

ALTHOUGH the idea of roasting zinc concentrates in suspension had intrigued investigators for a number of years, no commercial application of a process appeared successful until the development of the "Cominco" process. The efficiency and high capacity of this process may be judged by the fact that nearly all other electrolytic plants and many zinc retort plants in the world use this method. A furnace of the Cominco type can roast without special preparatory treatment and without supplementary fuel, mineral sulphides such as zinc sulphides and iron sulphides containing varying amounts of moisture at any desired rate ranging from one-half up to full capacity. The full capacity of a unit is in general about three times that of a multiple hearth furnace of the same size. The latest type of "Cominco" furnace can be built for capacities from 25 to 500 tons per day. The quality of the calcine is subject to positive control and may be

Jan 1, 1961

By J. Keith Seidler, David R. Lentz, Douglas C. Hall, Nicholas Susak

Abstract - The Ta-Nb-Zr-REE-rich McKeel Lake alkali granite pegmatite-aplite dike swarm is hosted within the late Silurian multiphase alkali granite intrusion (Welsford) near Browns Flats in southwestern New Brunswick. A steep easterly dipping series of pegmatite-aplite dikes trending 170º can be traced 150 m along strike; they are up to 40 cm wide, closely spaced (10-20 cm apart), and interconnected by narrow branching dikelets that generally trend perpendicular to the overall strike direction. The Welsford intrusion has mantle A-type affinities characterized by enrichment of Zr, Ta, Nb, Th, and rare earth elements (REE). Two separate sets of dikes have been identified: (1) an unmineralized fine-grained porphyry, which occurs at depth and seems to be the youngest intrusive phase; and (2) a mineralized pegmatite-aplite dike swarm (419 ± 20 Ma) that crops out at surface. The mineralized pegmatite-aplite dikes likely represent a late magmatic, highly fractionated phase of the Welsford intrusion. XRF and INAA data indicate that the Welsford intrusions and related pegmatite-aplite dikes show elevated levels of Ta (74-220 ppm), Nb (750-3,040 ppm), Zr (1,450-36,000 ppm), Y (540-3,070 ppm), Th (170-870 ppm), U (60-250 ppm), Ce (430-1,950 ppm) and Yb (110-290 ppm). Electron microprobe analysis of two samples identified Ta-Nb- and REE-rich phases: euxenite, fergusonite, aeschynite, (Y)-aeschynite, and a REE carbonate.

Jan 1, 2005

By P. G. Dunn, J. Fitzgerald

ABSTRACT The scheduling of underground mining activities is a complex task that must simultaneously satisfy a large number of constraints. A schedule optimization tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated through a case study. The maincomponents of the SOT include (a) a genetic algorithm that searches for optimal schedules, (b) guidance for the application of heuristic rules, and (c) sliding, which implements just-in-time development. Findings indicated that preliminary scheduling performed before invoking the SOT, intended to provide a good starting point for the search, did not ultimately lead to higher value schedules.

Jan 1, 2010

By J. L. Collins

"Une recherche debutee en 1987 tente de cerner divers éléments ayant un impact sur la productivite miniére, de facon à améliorer la planification des operations souterraines. II a été possible de recueillir jusqu'à trente variables dans sept opérations minières differentes du Nord-Ouest québécois. Cette présentation rend compte de quelques résultats préliminaires obtenus à l’une d'entre elle. Entre autres, elle montre comment une association entre une analyse de régression multiple et un logiciel d'optimisation (OPTIMUL) peut servir à une application particulière de la planification d'une opération minière du Québec. Plus spécifiquement, la présentation montre comment une quantité appropriée de ANFO et de TOVEX peut maximiser la quantilé de minerai cassé, minimiser les couts de sautage ou encore minimiser les coûts d'explosifs par tonne de roche cassée, en se basant sur une série de contraintes réalistes provenant de la mine.ABSTRACTA study, underway since 1987, tries to evaluate factors affecting mines' productivity. Information has been collected from seven underground mines in Quebec and this paper shows preliminary results from one. In particular, it shows how a combination of multiple regression analysis, mathematical programming and a set of realistic mine constraints can be used for a particular application of mine planning. More specifically, the paper shows a parallel between maximizing production of tons of broken are, minimizing explosives costs or minimizing the costs of explosives per ton of broken are by an appropriate selection of ANFO and TOVEX quantity of explosives. Finally, the paper shows that minimizing the costs of explosives per ton of broken are is the best alternative to follow providing a special optimization program can be set up."

Jan 1, 1990

By E. You

The concentrator at Kennecott Utah Copper currently has 4 lines with a configuration of one SAG mill feeding two ball mills. The slurry that reports to each ball mill will vary resulting in an unequal load of material. This configuration contains two separate sumps that receive material from a distribution box relying solely on natural slurry flow to feed each sump. The unequal split to each mill results in one mill receiving a greater amount of material. This will result in the equipment on one mill reaching limitations that may affect product quality and the operation of the equipment near maximum. The parallel mill in this condition will often have additional capacity that can be used but cannot be utilized due to the unequal split. The major consequences of this issue result in reduced throughputs and metal recovery. To resolve this condition an advanced control strategy was implemented to control the split in April of 2002 using equipment that was in place.

Jan 1, 2007

By W. B. Agocs

"IntroductionWITH THE DISCOVERY of natural radioactivity at the end of the 19th century, and the design of equipment for the detection of this phenomenon, radioactivity surveys bad their inception. Early in the 20th century it was found that almost all rocks are radioactive to a certain degree. This radioactivity is due to the nuclear disintegration of six naturally radioactive elements: potassium, thorium, uranium, rubidium, samarium, and lutecium.The radioactivity of these elements manifests itself by the emission of some concentration of alpha, beta, and gamma 'rays'. Of these, the alpha and beta 'rays' are, respectively, helium atoms and electrons, while the gamma 'rays' are short wave length x-rays generated in the nuclear disintegration by the transformation of mass into energy.The alpha and beta rays, being particles of matter, are stopped ve• easily by material barriers, but gamma rays are extremely penetrating and they will pass through a foot or more of rock or several inches of lead.The radioactivity may be detected by the causing of ionization by the radiation. The radiation detectors may be divided into four classes: ionization chambers, proportion al counters, and Geiger counters, all of which use gas for ionization, and scintillation counters, in which a solid is ionized. The basic principle of all these detectors is the same; the difference lies in the method used to measure the degree of ionization produced by the rays. Currently, the scintillation counter is displacing, the other instruments in radioactivity surveying."

Jan 1, 1955

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By R. K. Collings

Mineral wastes from the mining, metallurgical and chemical processing industries in Canada amount to about 800 million tonnes annually. Such wastes often are largely non-metallic in composition and are of interest for traditional non-metallic mineral uses and applications. Mineral waste disposal and maintenance are costly; furthermore, these wastes may pollute groundwater, rivers and lakes. These factors and an increased appreciation of the potential utility of some mineral wastes have stimulated research in this area.

Jan 1, 1984

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By A. A. Iranzadeh

The performance of a tunnel boring machine (TBM) depends on the efficiency of the cutters, which can be influenced by geological conditions and rock mass properties. In this study, a three-dimensional numerical model, based on a discrete element method, was used to evaluate the effects of joint orientation and its spacing on the fragmentation process by a TBM cutter. Several models were constructed to study the effects of variable orientation; these models incorporated different spacing, variable spacing, different orientations on the fragmentation process, and different sections of the block model. Three parameters, consisting of induced tensile stress, induced shear stress and maximum displacement, were calculated. The stress in each section that forms chips was considered as critical stress; critical joint spacing and orientation in each section were determined. Results show that the critical orientation was in the range of 45 to 60º, where there was a possibility to achieve the maximum penetration rate. The critical joint spacing was 200 mm and, by increasing joint spacing, the value of critical stress decreased significantly. Furthermore, joint orientation could influence more than joint spacing in the rock cutting process.

Jan 1, 2009

By M. Rafiee

Indoor physical security, as a perpetual and multi-layered phenomenon, is a timeintensive and labor-consuming task. Various technologies have been leveraged to develop automatic access control, intrusion detection, or video monitoring systems. Video surveillance has been significantly enhanced by the advent of Pan-Tilt-Zoom (PTZ) cameras and advanced video processing, which together enable effective monitoring and recording. The development of ubiquitous object identification and tracking technologies provide the opportunity to accomplish automatic access control and tracking. Intrusion detection has also become possible through deploying networks of motion sensors for alerting about abnormal behaviors. However, each of the above-mentioned technologies has its own limitations. This paper presents a fully automated indoor security solution that leverages an Ultra-wideband (UWB) Real-Time Locating System (RTLS), PTZ surveillance cameras and a Building Information Model (BIM) as three sources of environmental data. Providing authorized persons with UWB tags, unauthorized intruders are distinguished as the mismatch observed between the detected tag owners and the persons detected in the video, and intrusion alert is generated. PTZ cameras allow for wide-area monitoring and motion-based recording. Furthermore, the BIM is used for space modeling and mapping the locations of intruders in the building. Fusing UWB tracking, video and spatial data can automate the entire security procedure from access control to intrusion alerting and behavior monitoring. Other benefits of the proposed method include higher accuracy and robustness, more complex query processing, and interoperability with other BIM-based solutions. A prototype system is implemented that demonstrates the feasibility of the proposed method.

Aug 1, 2013

By F. A. Auld

"Traditionally deep shaft sinking from the ground surface was carried out using drill and blast methods. Although large diameter blind shaft drilling has been carried out successfully on numerous occasions previously, including as early as 1852 in Germany (Auld, 1995), little attempt has been made until more recently to mechanise the shaft sinking excavation process using down-the-hole machines. This paper reviews the development of deep shaft sinking machines from the early 1970’s up to the present day. INTRODUCTION Mechanical excavation methods can significantly improve excavation performance, in order to access natural resources faster, and labour safety is increased compared to drill and blast operations. However, shaft sinking machines need to be capable of accommodating all the basic requirements for deep shaft sinking, namely: 1. Excavation and muck removal 2. Ground stability control 3. Groundwater ingress control 4. Temporary lining installation 5. Permanent lining installation and watertight sealing 6. Ventilation 7. Secondary means of egress for personnel In addition, how the machine operates in the shaft is an important factor, either slung on ropes from a surface headgear or on its own in the bottom of the shaft. An all-embracing machine which can deal with all of the above conditions is impossible but many of these requirements can be incorporated into a single machine. Deep shaft sinking also differs greatly from normal tunnel construction which employs the use of either a roadheader arm installed within a shield or a full-face tunnelling machine for excavation. Hydrostatic pressure and ground stability problems increase with depth, whereas in tunnelling the depth is normally relatively shallow and the aforementioned factors remain approximately constant along the tunnel length. DEEP SHAFT SINKING MACHINES All the shaft sinking carried out previously in the UK was by the traditional method of drill and blast. Elsewhere, in other parts of the world, attempts have been made to mechanise the process."

Jan 1, 2019