Search Documents

By Masakazu Daté

Moisture effect has been studied for the CO oxidation over Au/TiO2, Au/Al2O3 and Au/SiO2, in the range of H2O concentration over four orders of magnitude. It has been found that the catalytic activity is generally enhanced by moisture in the reactant gas. The enhancement is as large as two orders of magnitude. Response to the moisture concentration, however, depends on the support oxide, indicating different contributions of the support to the reaction steps. The moisture effect is reversible and the activity is mainly determined by the amount of moisture absorbed by the catalyst. The apparent activation energies are not significantly influenced by moisture for Au/TiO2 and Au/Al2O3. On the contrary, non-uniform conversion curves versus temperature observed for Au/SiO2 are drastically changed, which indicates that the reaction over Au/SiO2 does not take place at low temperatures without moisture. The moisture effect may be probably attributed to the decomposition of carbonate species accumulated during the reaction, while the ?OH group might directly participate in the reaction pathways as a promoter.

Oct 1, 2003

By P. M. Solozhenkin, O. I. Ibragimova, I. P. Solozhenkin

Molecular models of complexes of poorly studied bismuth, gold, and arsenic mineral clusters and reagents were created for use in collector activity forecasting using Chem Bio 3D and ChemOffice2005, with optimization by MM2. The density functional theory approach was used to determine HOMO, LUMO, SOMO, and total energies, atomic charges, and s, p, d- populations for various compounds. The structure-based virtual screening (SBVS) and docking technique was proposed to reduce the vast number of compounds to a more manageable number for selection of potential flotation candidates. The prognosis of collector activity evaluation (PCAE) strategy was proposed as a consistent approach to estimate the interaction between a collector and a mineral cluster as the difference between the total energy and sum of cluster energy and collector energy to search the analogue of butyl xanthate. The negative relationship between PCAE and flotability was shown. The combinations of dialkylamino sulfhydryl collectors can be considered as prospective reagents for gold-bearing sulfide ore flotation. These results were confirmed by experimental data in ore flotation. The increase in recovery of gold and bismuth with the aid of a combination of reagents has been established and additional cyanidation of tailings has been avoided.

Jan 1, 2016

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

By David R. Lentz

At True Hill in southwestern New Brunswick, low-grade porphyry-style Bi-8n-Mo greisen mineralization is associated with the cupola of an epizonal granite porphyry (granite) that also exhibits three episodes of brecciation. The first episode of brecciation is an in situ, 8 m to 10 m wide transitional zone of net-veined to coarse-grained "blocky" endogranitic mesobreccia that is chloritized and greisenized and hosts weak disseminated minerali.zation. In a zone closer to the host rockgranite contact, angular fine- to coarse-grained endogranitic mesobreccia with greisenized matrix is superimposed on the earlier transitional breccia. The latest episode is fault-controlled and consists of quartz- and chalcedony-hosted sub-angular to rounded fine-grained "pebble" mesobreccias that crosscut and brecciate the other breccia types, as well as the adjacent altered metasedimentary country rocks. The first two episodes of brecciation are magmatic-hydrothermal in origin related to hydrofracturing of the granite carapace and are accompanied by greisenization and mineralization, whereas the post-mineralization, silica-hosted, "pebble" mesobreccias related to hydromagmatic, low-temperature fluid circulation and/or boiling along faults near the contact. These magrnatichydrothermal and hydromagrnatic mesobreccias are similar to those associated with W-Mo-Bi porphyry-greisen mineralization at the Mount Pleasant deposit.

Jan 1, 1994

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By B. Kruger

The Dundee Precious Metals Tsumeb Smelter has evolved over the last decade to meet the challenges and opportunities brought about by a changing copper concentrate market, technological advances, environmental legislation as well as social and political changes. The paper discusses some of the challenges, successes and lessons learnt through the expansion and modernization of its smelter complex. It considers the details and impact of the transition from slag granulation to that of slag slow cooling as well as the improvement program that was implemented to more than double the refractory campaign life of the Ausmelt furnace from around 6–9 months to 15–18 months. In addition, given the evolving world we live in, it considers the challenges that the smelter faces today, not the least of it being how to remain relevant in an age of digital and other 4th Industrial Revolution disruptions. INTRODUCTION Dundee Precious Metals Tsumeb (DPMT) Smelter is located just outside the town of Tsumeb, in the Oshikoto region of Namibia. It is the largest town in the region with a population of approximately 45,000. The smelter was built in the early 1960s to treat concentrate from the nearby Tsumeb copper mines. Construction of the site was completed in 1962 and the smelter was officially commissioned in 1963 by Tsumeb Corporation Limited (TCL). At the time the smelter consisted of a lead section (including a refinery), a copper section and plants that produced cadmium, sodium antimonite and arsenic trioxide. Production commenced in early 1964, with 3,500 tonnes of copper and 6,000 tonnes of lead being produced per month. TCL was acquired by Gold Fields South Africa in 1988, and a few years later the lead section was shut down due to reduced lead content of the mined ore. In mid-1996, all mining and smelting operations were halted due to labour strikes. Ongopolo Mining and Processing Limited (OMPL) re-opened the mines and the smelter in 2000, only operating the copper section of the smelter. At the end of 2008, all mining operations were halted by the new owner of OMPL, Weatherly Mining International, while the smelter continued to operate. The closure of the Weatherly owned mines in Namibia, the primary feed source to the Tsumeb Smelter, meant that the smelter had to transition its business model from operating as a ‘captive smelter’ to that of a ‘toll smelter’. Its Ausmelt Top Submerged Lance (TSL) smelting technology and various ancillary plants made it especially suitable for accepting and treating complex concentrates that were available on the global market.

Jan 1, 2019

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By K. Cybulski

Coal dust explosions still remain the main hazard in the coal mining sector, notwithstanding their relatively wide recognition compared to other hazards and the development of effective methods of prevention. Coal dust explosions are still the cause of numerous catastrophes, often leading to fatalities. Fortunately, they rarely occur, and it is for this reason that their hazardous impact is often underestimated. This problem in Poland is being exclusively solved by the Central Mining Institute, Experimental Mine Barbara. Here, basic research on the phenomenon of coal dust explosions and prevention methods is carried out, as well as investigations into the causes and circumstances of past accidents. After 15 years of no coal dust explosion accidents in Poland (1987?2002), a few coal dust explosions have recently occurred, with tragic consequences. These events have taken place not only in hard coal mines, where the presence of dangerous coal dust is the result of common production cycle, and safety measures against coal dust explosions are subject to specific regulations, but also in coal-fired power plants. This is of special concern because prior to 1987, such accidents had been been reported only for coal mines and not for coal-fired power plants. In recent years, two dust explosions occurred in Polish power facilities: the Dolna Odra and Turow power plants. In both cases, coal dust explosions occurred in the fuel supply system, but biomass dust was also involved. The explosions caused significant damage to the systems and buildings. This paper gives description and schematics of the regions of catastrophic coal dust explosions that have occurred in recent years in Poland, as well as the results of post-accident investigations, presenting the coal dust explosion hazard at the accident scene The results specify in detail the state of safety measures against coal dust explosions in light of the relevant regulations in force, including amount of deposited coal dust, content of incombustible matter in coal dust, free moisture content in coal dust, state of coal dust explosion safety zones, and state of explosion barriers. The conclusions from the site inspection and post-accident investigations presented enable us to determine locations of explosion initiation, probable ignition sources, range of explosion flames, and explosion barrier performance. A complete elimination of coal dust explosion hazard at the site of dust deposition is practically impossible to achieve. Similarly, a total elimination of ignition source, which may be related to the occurrence of other natural hazards, equipment malfunction or human errors, is impossible. The examples of tragic events that took place in Polish coal mines and coal-fired power plants highlight shortcomings and mistakes made in terms of assessment and prevention measures taken against the coal dust explosion hazard.

Aug 1, 2013

By J. M. Cummings

The importance of controlled sand properties to the production of quality castings has been recognized by foundry men for many years, but the maintenance of requisite standards results in a relatively high sand consumption, which in steel foundries, for instance, may range from half a ton to over one ton of sand per ton of finished casting. During the war, obtaining and maintaining adequate sand supplies became a serious problem in many foundries, owing to increased wartime production and serious 'bottlenecks' in transportation. As a result, considerable interest was aroused in the possibilities of various sand reclamation systems by which up to 85 or 90 percent of discarded sand may be returned to a usable condition. During the past five years or so, a number of sand recovery installations have been made by both ferrous and non-ferrous foundries in Canada and the United States, and have resulted in substantial reductions in sand costs in every case. The possible benefits of sand reclamation are particularly apparent in British Columbia where no suitable sands for steel and heavy iron foundries occur naturally, and where freight costs on imported sands are considerably higher than initial selling prices. This is well illustrated by the fact that silica sand, which sells for about $2.00 per ton at pits in Illinois, is laid clown in British Columbia for around $11.00 or $12.00 per ton. The operating costs quoted for certain of the reclamation schemes, i.e. $0.25 to $1.50 per ton, may actually be no higher than the cost of waste sand disposal in city-located foundries. In view of the foregoing considerations, the British Columbia Research Council has undertaken a study of the possibilities for sand reclamation, with particular attention directed to its application in local steel foundries. No commercial occurrences of silica sand are known in the Province, and, with this in view, the Council previously investigated the possibility of recovering silica sand from local impure sands. Results were definitely encouraging, but it was felt that the present market is too small to permit economical production by the method developed.

Jan 1, 1947

By M. Tanaka, Y. Sato, H. Narita, S. Alam, T. Ogata

To ensure a stable supply of rare earth elements (REEs), it is highly necessary to establish the corresponding recycling technologies for RE magnets and phosphors in inplant wastes and endoflife products. Solvent extraction using 2ethylhexylphosphonic acid mono2ethylhexyl ester (EHPNA) is often applied in the separation and purification of REEs. In this study, the equilibrium distribution ratios of neodymium and dysprosium between 1 mol/L nitrate solution and the EHPNA in an alkane diluent were measured at 298K. The experimental data were analyzed by correcting the nonideal behavior of the organic phase using the Alstad empirical equation under the assumption that a complex with a molar ratio of 1:6 (REE:extractant monomer) was formed. The model correlated well with the experimental data and the extraction equilibrium constants were obtained. The extractant equilibrium constants obtained by this methodology would be useful in the design of REE recycling processes using solvent extraction.

Jan 1, 2014

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwesternmost part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1970

By Gonzalo Díaz, Diego Mesa, Willy Kracht

"It is well known that frothers affect the amount of water that is transferred to the froth, which has an effect on both the froth stability and the water recovery. On the other hand, since non-selective recovery by entrainment is directly related to water recovery, it can be said that frothers have an indirect effect on flotation selectivity. Recent research on this subject has shown that the non-selective recovery by entrainment, which is characterized by the entrainment factor, is frother dependent. In other words, the entrainment factor is not unique, but depends on frother type.Having different entrainment factors implies that for the same water recovery, the amount of undesired particles reporting to the concentrate may vary if one changes the frother type, which suggests, as a possible explanation, that it is not only the amount of water in the froth what is affected by frother type, but also the froth structure.The purpose of the current work is to study the effect of frother type on foam structure (two phase froth). A quasi-2D cell operated with a slot sparger was used to study the foam structure in the presence of three different frothers: Methyl Isobutyl Carbinol (MIBC), OrePrep®549, and Octanol at the same gas flow rate and reagent dosage. The foam structure was studied using image analysis, and an algorithm based on textural analysis was developed to classify the foams. The results show that it is possible to classify foams according to the frother used, which proves that frothers have an effect on the foam structure.INTRODUCTIONFrothers are usually dosed paying attention to froth stability, condition that is commonly estimated by sight, according to the operator's criteria and experience. This happens because there is not an established procedure or technique for frother characterization, generating qualitative descriptions such as “powerful” or “selective” frothers, which lack of scientific thoroughness and remain under subjective factors. Nevertheless, several works have been done in this line of research. Moyo et al. (2007) classified frothers based on their water-carrying capacity, proving that this characteristic is related with gas holdup and frother type. Previously, Trahar (1981) had related water recovery and gangue particles recovery, defining the entrainment value (ENT). Nowadays it is known that entrainment affects both hydrophilic and hydrophobic because it is not a selective process. In the last decade some studies (for example the one of Konopacka and Drzymala (2010)) delved into different entrainment behaviours dependent mainly on the flotation type (batch or continuous, agitated or columnar, etc.), but there were no studies on the effect of frother type regarding entrainment, since Rahal et al. (2001) argued that the ENT factor was independent of the frother type and concentration, and froth height."

Jan 1, 2016

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By A. B. Rossetti

"THE MISSION TO Offshore Scotland was in my opinion a very worthwhile venture, as it indicated the scope of the offshore oil and gas business and how we might exploit it to the fullest here in Nova Scotia - if our offshore fields eventually become producing fields. The writer was able to attend a considerable number of lectures and as a result gained some valuable know-how on the engineering design, financing and operation of the North Sea oil industry. There are many new fields of technology that had to be developed to overcome the North Sea's hostile environment and a great deal of the same technology will have to be developed to win oil and gas from our continental shelf. The visit left me with several impressions, which in the main are:(1) The high order of investment required to develop offshore oil. The investment ranges from 10 to 20 times that required for a similar output on land. Each barrel of oil costs on the average of about $2,- 500 per barrel per day.(2) Because of the high investments required, before the first oil is produced the field must be brought into production at the earliest possible date and initial lead time from decision to production is less than four years. In the British Petroleum field, working at a depth of 450 feet will require an investment of $900,000,000 to develop a production of 400,000 bbl per day. (3) The size and complexity of equipment required is beyond anything ever imagined. Problems which must be overcome are such factors as water depth, wind velocities, wave height, wave period, long periods of darkness, low temperatures, distance from land, and fog."

Jan 1, 1973

By J. O. Wheeler

"DEFINITION OF THE REGION, ITS BOUNDARIES, AND PHYSICAL AND GE'OLOGICAL CHARACTERISTICSTHIS PAPER concerns the Western Cordilleran region, embracing most of British Columbia, the southern half of Yukon Territory and the southwestern most part of the District of MacKenzie. It excludes Vancouver Island and the Queen Charlotte Islands, which are discussed in a background paper on the Pacific Continental Shelf. The region is bounded on the south by the northwestern United States, on the west by the continental shelf and Alaska, on the north by the front of the Ogilvie Mountains, on the northeast by the axis of the MacKenzie Mountains and on the east by the Rocky Mountain Trench.The region is dominated by two mountain chains that con tain icefields and glaciers: the St. Elias, Coast and Cascade Mountains in the west; the Selwyn, Pelly, Cassiar, Omineca and Columbia Mountains in the east. The Intermontane region between these mountain chains consists of lower mountains and plateaus. In the mountains, the region above the timberline and many of the steep valley-walls provide good exposures of rock, but these areas are subject to rockslides and landslides and in winter to snow avalanches. Much of the Western Cordillera was covered by ice-sheets at various times during the Pleistocene epoch. Consequently, the larger valleys in the mountains and much of the Intermontane region contain much glacial drift and alluvium and only limited exposures of rock. This same terrain in the Southern Cordillera, however, is the most favourable for agriculture. Parts of the region, particularly in the two mountain chains, are heavily forested. Elsewhere, the forest cover is less, with grassland prevailing in the south and tundra in the north."

Jan 1, 1969

By Mark B. Thorpe

Golden Star Resources started gold mining operations in Africa in 1999 after 15 years of exploration in South America. At the time, the approach to local assistance was through "alternative livelihood" programs and the donation of infrastructure to local communities. This was initially successful with local community support. However, with time and on reviewing the implemented projects, it became evident that the success was limited and many if the projects were either poorly used or in disrepair. Through a review of the options, we decided to develop a community assistance model driven by the communities themselves, while keeping control of the finances and the actual construction of the projects. Through the formation of the Golden Star Development Foundation, we began to support community driven projects for local economic development. The evolution of economic development projects continued over the next several years with the addition of project requirements for partnerships with government, and finally an evolution to a partnered turn-key piece of infrastructure that we hand over to an agency for operation and ongoing maintenance. We are currently working with outside partners to further our economic development activities in Ghana to the benefit of our stakeholders.

May 1, 2011

By Z. D. Hora

Limestone of economic interest is widespread in British Columbia. Triassic deposits on Texada Island are a convenient 1idewa1er source of li111es1one for cemen1 and lime for 1he Pacific orthwes1. Permian limes/one near Pavilion Lake is used for quicklime, and a deposit near Kam/oops is used for cement. Quarries at Dahl Lake and Pwrmigan Creek serve local pulp and paper needs.

Jan 1, 1984

By C. A. Pickles

Microwaves are being applied industrially in a number of fields and possess a number of potential advantages that could be applied in extractive metallurgy. Microwave heating has a number of unique characteristics, which distinguish it from the conventional heating methods. In microwave heating, the absorption of energy occurs at the molecular or atomic level and therefore the heat is generated within the material itself. In conventional heating, the exterior temperature is usually higher than the interior, but with microwave heating, the temperature gradient is inverted and thus the interior temperature can be much higher than that of the surface. The energy densities in microwave systems can be relatively high and this in combination with the low thermal conductivities of oxide ores, can lead to very high internal heating rates. In this research, the application of microwave energy for the reduction of a nickeliferous silicate laterite ore has been investigated. The real and imaginary permittivities are the two fundamental properties which determine the microwave absorption characteristics of a material and these were measured for the ore, both with and without carbon additions using the cavity perturbation technique. The microwave heating and reduction experiments were performed in a 0 to 2 kW CTC microwave system. The effects of power input, processing time, sample mass and charcoal additions on the microwave absorption were investigated. Then reduction experiments were performed and the nickel grade of the magnetic concentrate and the nickel recovery in the concentrate were determined.

Jan 1, 2005