Search Documents

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By E. Esmaeilzadeh

There arc 8 primary ball mills in the concentrator plant and their task is material crushing. At the time of balls charge to mills, a lot of noise is produced. This noise would affect all grinding areas. The aim of this research was a reduction about 16 dB at source sound power level (SWL was 129.1 dB). With considering two noise control principles, noise producer sources and propagation paths were specified. For removing and reducing of noise producer sources, rubbers with a thickness of 5-20 mm were used on the all inside surfaces of charge box, ball transferring box and exit canal. For increasing transmission loss and damping coefficient of charge box body, rubber with thickness of 1 cm at outside surface of box was used. For reduction of noise propagation a secondary metal cover was designed and made. This cover includes two parts and was set around the charge box. Glass wool (75 kg/m3) with 10 cm thickness was used as acoustical absorbent between free space of two body's layers and from secondary cover side. The of the rest space was left empty. After installing of secondary cover on the ball charge box no.4, SWL showed a reduction about 16 dB. For studying of control system effect on noise reduction at points far from of charge place, measuring results at these points showed the maximum reduction 12.1 dB and the minimum 11.8 dB.

Jan 1, 2007

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By R. B. Paine, B. M. Wright

"Syncrude has entered a new era involving the use of pipeline slurries to convey oil sand to the extraction plant. Hydrotransport operations and base plant operations encounter vast performance differences when processing different types of oil sand. This paper describes the hydrotransport process, its history at Syncrude, methods of describing the source ore characteristic and plant performance. The use of this information within Syncrude and how it will be managed on an ongoing basis will also be described. IntroductionThe Syncrude Canada Ltd. site is located 43 km north of Fort McMurray, Alberta, on the Athabasca oil sand deposit. The Syncrude operation consists of mining, extraction, upgrading, utilities and other support facilities. The mined ore is sent to the extraction plant where water and solids are removed from the bitumen. The bitumen is then sent to the upgrading plants to be further processed into Syncrude Sweet Blend (a light sweet crude oil). Syncrude produced 73.5 Mbbls of Syncrude Sweet Blend in 1996 and produced 75.7 Mbbls in 1997. Prior to 1993, Syncrude moved ore from the pit to the extraction plant via four dragline / bucketwheel/ conveyor systems. These systems, supplemented by auxiliary ore crushers, satisfied the feed requirements of the extraction plant. Ore was conveyed to the control tower area and placed in the dump pocket via four radial stackers. Various blending scenarios occurred at this point, using feed from the four mining quadrants and from auxiliary feed crushers. Upon entering the extraction plant from the base mine, the oil sand passed through a series of tumblers where it was mixed with hot water and caustic. It then proceeded to one of four primary separation vessels where bitumen froth was floated off and the middlings and coarse fractions were recombined and sent to the tail oil recovery vessels, or TORs, for further processing."

Jan 1, 1999

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By John T. Ling

"This paper describes the operation of a rope haulage used as the main system of transportation in an underground coal mine. Prince Colliery, which is operated by the Cape Breton Development Corporation, has been in operation for 23 years and produces 1.2 million tonnes of coal annually. The mine extends a distance of 8000 metres under the Atlantic Ocean. All personnel and supplies are transported by means of an endless rope haulage system consisting of a train of rail cars that are operated by an electric engine on surface. The wire rope is 15 km long and weighs 63 tonnes. The system is believed to be the longest of its type used in an underground coal mine. The design of the system, safety features of the haulage, and problems encountered during the design and construction are described. IntroductionCoal has been mined commercially in Cape Breton, Nova Scotia since the 1800s. Several coal seams that are part of the Sydney coal fields, dip toward the north and northeast out under the Atlantic Ocean at angles between -4 and -15 degrees. Coal has been economically mined at depth in excess of 1200 m and more than 11 km from the coastline.Traditionally, single and double drum hoists have been used to haul the coal to the surface and also for transporting the workers and the materials required for mining up to 8 km. With the introduction of mechanized mining methods in the late 1960s, conveyor belts began to replace rope hoists for coal transportation. Improvements in hoisting system design also allowed for drums that could wind up to 6100 m of 32 mm wire rope in 15 layers.These hoists are commonly referred to as “drop hoists” because they take advantage of the gradient of the slope to assist in allowing the mine car train to reach the end of travel. The cars travel on steel rails and the rope is guided by rollers to reduce friction in the system."

Jan 1, 1999

By E. Nurminen

Thermal transport properties of copper flash smelting flue dust have been investigated. Such values of the dust are needed to correctly model the process and to optimize its heat recovery performance. Dust accretions on heat recovery boiler walls may have a significant influence on the boilers heat transfer efficiency. Measurements of the thermal transport properties have been made for industrial flue dust and for pure sulphate components. The measurements have been conducted at temperatures up to 400 °C and the effect of porosity on these properties has also been investigated. The results indicate that the flue dust and the sulphate components are effective thermal insulators and the dust build-up on the boiler walls is likely to greatly decrease the heat transfer efficiency of the boiler.

Jan 1, 2007

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

By J. E. Hawley

"The property of Francoeur Gold Mines, Limited, lies directly west of the Armfield mine in Beauchastel township, Abitibi district, and 12 miles west and slightly south of Noranda. The gold deposits are of particular interest because of their replacement character and close association with fault zones. The property was originally staked in 1923 following the discovery oi a mineralized zone near the eastern boundary. This became No. 1 orebody. Later discoveries in 1936 of No. 2 and No. 3 orebodies led to underground development and actual mining in July, 1938. A fourth orebody, No. 8, was found in 1939.The following is the production record up to December 31st, 1947:Beginning in September, 1944, ore was shipped to Noranda as siliceous flux, but late in 1946 milling of low-silica ore from No. 1 orebody was undertaken until operations were temporarily suspended in 1947.The four main ore deposits, Nos. 1, 2, 3, and 8, consist of siliceous ferrocarbonate and albite replacement bodies mineralized with fine pyrite and specularite in schistose fault zones in Keewatin volcanics. Barren to low grade quartz veins though present in some are uncommon, but small stringers of quartz are usually present wherever here and there visible gold is found. Nos. 1, 2, and 3 deposits lie in a major fault zone that extends completely across the property from west to east (over 7,000 feet) and dips N.40° to 50°, and are separated by intervals of 1,800 to 2,000 feet respectively. The fourth lies in a smaller fault zone striking east and dipping on the average 65°S.No. 1 orebody has been explored by mining to a depth of 500 feet, No. 2 to 400 feet, and No. 3 to slightly less than 300 feet . The greater part of No. 8 lies above a depth of 200 feet, but a raise has recently .been driven through from the west end of the 5th level of No. 1 to the 2nd level on No. 8 zone. Most of the ore of No. 8 zone above the 2nd level and of Nos. 2 and 3 above the 3rd levels has been removed."

Jan 1, 1954

By Peter Moser, Thoma Oberndorfer

"Within the research project “Mine Development” (Fettweis and Moser, 1990) a PC-based mine database has been built up since 1991 and so far includes detailed technical and economic data of about 150 under-ground hardrock mines in industrialized countries worldwide. These data represent about 50% of the underground hardrock mines in west and central Europe, Scandinavia, United States, Canada and Australia (Fig. 1). The mining operations included in the database have been visited directly and analyzed with respect to their deposit conditions, their general design and layout and also their operational and economic performance.The main aim of the Mine Database is to make a contribution to an improved planning of new underground hardrock mines. An analysis of current mine planning practices shows, that both personnel and company experience is still a dominant factor in planning new underground hardrock operations. Through the information included in the Mine Database the experience of a single per-son or company is supplemented by the experience of a wider group of people. The Mine Database makes the huge amount of experience that is available worldwide in the field of under-ground mining accessible for new mining projects. From that a contribution to a more reliable mine planning procedure based on the performance of existing mining operations is expected.In addition to its use in planning new mining operations, the Mine Database can con-tribute to the exchange of technical data among different mining operations, especially on equipment performance, etc. Such an information service is offered by the Department of Mining Engineering & Mineral Economics in Leoben and is already being used by different mining companies. To respect proprietory information, company specific information is not released under any circumstances.The cost of building up the Mine Database, so far, is about US$500.000 — two thirds of which is labour, and one third, travel."

Jan 1, 1996

By Silvio E. Kruger

Real time measurement of wear and corrosion provides crucial information needed to determine an optimal schedule for corrective maintenance and is a powerful tool to maximise equipment availability and reliability. It also leads to savings from optimized spare parts handling and helps to avoid costs of accidents and their negative impact on safety and the environment. This paper presents the technology of ?painted-on? ultrasonic transducers that can be integrated to structures and accurately measure the remaining thickness and therefore determine wear or corrosion losses. These transducers have a small footprint, a performance comparable to other commercially available ultrasonic transducers and can sustain temperatures as high as 400ºC. The application of this technology to mining equipments and its potential benefits are discussed.

Aug 1, 2013

In this paper, the use of electrochemical AC impedance spectroscopy (EIS) for in-situ diagnosis of high temperature PEM fuel cells is described. EIS was performed on single cell hardware, built in-house, using a fuel cell test station modified to operate up to 120°C and 30 psig. Electrode kinetics, membrane resistance, porous-layer and mass transport impedance of MEAs, assembled in-house, were measured at various current densities for the purpose of validating the test station and cell hardware, and for optimizing MEA and flow-field designs. The effect of temperature and humidity on the various impedances was investigated. Impedances obtained at lower and higher temperatures were compared to obtain insight into the issue of water management in operating fuel cells.

Jan 1, 2005

By M. Hosseinzadeh

By changing the quality of consumed refractory bricks in burner zone of sarcheshmeh copper complex anod kiln removing of carbon precipitation phenomenon was studied. For blister deoxygenation LPG is blowing in anod kiln and cause destoring microsturcture and bonding of refractory bricks. Studies are shown that in a part of the bricks which have a temperature of 800 - 1000 °C , iron content phases in magesia - chromite bricks are like catalist and cause increasing the rate of carbon precipitation reactions . In a way that in comparsion of two bricks with best and medium quality with different analysis, this problem is more critical in best quality bricks containing high iron oxide. Therefore special magesia spinel bricks suggested and installed in burning zone.

Jan 1, 2004

By Carmen Mihaela Neculita

Sulfate-reducing passive bioreactors efficiently treat acid mine drainage (AMD) by increasing its pH and alkalinity and by removing metals as sulfide precipitates, in addition to hydroxides and carbonates. However, the new mining legislation sets discharge limits based on physicochemical parameters and on the non-toxicity of treated effluent as well. In this study, toxicity was assessed for effluent from 3.5 L column bioreactors filled with mixtures of natural organic carbon sources and operated at two different hydraulic retention times (HRTs) of 7.3 d and 10 d for the treatment of a highly contaminated AMD. Acute toxicity was observed for D. magna, and a toxicity identification evaluation (TIE) procedure was performed to identify potential toxicants. To help the interpretation of the toxicity results, metal partition in the effluent was also determined by filtration and ultrafiltration, while geochemical modeling was performed for metal speciation evaluation. The 10 d HRT effluent was nonacutely lethal for rainbow trout but acutely lethal for D. magna, whereas the 7.3 d HRT effluent was toxic for both organisms. The toxicity to D. magna was eliminated by 2 h of aeration for the 10 d HRT effluent, and the TIE procedure suggested iron as a cause of toxicity. However, the 2 h aeration eliminated the toxicity of the 7.3 d HRT effluent, only if performed after the pH rising to 9.3. Data regarding metal speciation indicated instability of both effluents during aeration and were consistent with the toxicity being caused by iron. The study indicates that design of passive treatment should include sufficient HRT and posttreatment aeration to meet acute toxicity requirements. Keywords: acid mine drainage, sulphate-reducing passive bioreactors, hydraulic retention time, effluent toxicity, metal speciation

Nov 1, 2008

Operationalizing the Ruggie Framework in a Mining Context Ruggie?s 3 Pillars: The State?s duty to Protect Policies, regulation, adjudication The Corporation?s responsibility to respect Acting with due diligence to avoid infringing Addressing adverse impacts when involved in abuses Access to Remedy ??even the most concerted efforts cannot prevent all abuse.?

May 1, 2013

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014