Search Documents

By Byron S. Kutscher

This report summarizes the program to develop and construct an improved light-scattering dust monitor (ILSDM). This improved light-scattering dust monitor, which operates on the forward light scattering principle, provides instantaneous measurements of airborne dust concentrations in units of mg/m. The program was divided into two phases. Phase I involved the design of the ILSDM which was reviewed by the Bureau of Mines. Phase II included the fabrication of a prototype ILSDM based upon the design developed during Phase I. After completion, the ILSDM was delivered and demonstrated at the Bureau of Mines. A description of the final ILSDM design, operating instructions, maintenance instructions and recommendations for additional work are also included in this report.

Jan 1, 1980

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By William M. Knuth

The objectives of this study were the evaluation of the technical and economical feasibility of utilizing color and color infrared aerial photography to satisfy some informational needs for pre-mine planning, mine progress monitoring, and reclamation monitoring. Seven aerial data collection missions were conducted within a two year period over strip mine sites in Pennsylvania. Scales of 1:6,000; 1:12,000; 1:24,000; and 1:48,000 were flown on the first aerial mission. The 1:12,000 was chosen as the optimal scale for the remaining six flights. An extensive literature and legislative review and discussions with strip mine operators identified the informational parameters that could possibly be obtained from aerial photography. Interpretability accuracies were evaluated for parameters in the broad categories of land use, soils, water, vegetation, and geology. Seasonal interpretation characteristics were noted for infrared photography. Man hours for photointerpretation and costs of aerial data collection were monitored closely and incorporated into a cost benefit analysis. Those parameters that could be mapped, identified, or measured with accuracies =75 percent were incorporated into a photointerpretation training manual. An additional analysis was performed to determine the applicability of the interpretation methodologies and results developed for Eastern sites to Western surface coal mining sites. In addition, a separate aerial photographic interpretation manual was produced during this contract. It is intended to be utilized by eastern and midwestern surface mine operators and regulatory personnel.

Jan 1, 1978

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The National Institute for Occupational Safety and Health (NIOSH), through an informal partnership with industry, labor, and the Mine Safety and Health Administration, has developed and tested a new type of instrument known as the personal dust monitor (PDM). The dust monitor is an integral part of the cap lamp that a miner normally carries to work and provides continuous information about the amount of respirable coal mine dust in the breathing zone of that individual. Testing was conducted on 25 prototype instruments in the laboratory to verify the instruments’ accuracy as received from the manufacturer and after a period of underground use. The laboratory testing verified previous work; there is a 95% confidence that the individual PDM measurements were within ±25% of reference measurements. In-mine testing determined the precision, durability, and miner acceptance. Data from the mines showed a field precision of 0.078% relative standard deviation for the PDM and 0.052% for the recognized standard—the coal mine dust personal sampler unit. The PDM had about 90% availability for collecting valid information in over 8,000 hr of underground use. Anecdotal comments by miners indicated that they found the PDM more convenient to wear for sampling than currently used instruments because of the integration of the sampler into the normally worn cap lamp. The means of the instruments’ pre- and postmine accuracy verification test values were statistically equivalent. Additional data were collected to measure the equivalency of the PDM to the U.K. Mining Research Establishment sampler, as required by U.S. law. However, analysis of the data was more complex than originally anticipated because the variance with increasing concentration required use of a more sophisticated statistical model. Explanation of and results from this work will be the subject of a second publication. Under the broad range of test conditions covered in this work, the PDM functioned as well as the current sampler in terms of availability for use, accuracy, precision, and miner acceptance.

Jan 1, 2006

By Daniel Ng

The U.S. Bureau of Mines-Michigan Technological University mine ventilation mainframe program was successfully adapted for execution in a personal computer (PC). The hardware requirement can be as modest as 256 kilobytes (33) of random access memory (RM) and two floppy disk drives. A version compiled for a PC possessing 512 Kb RAM has arrays dimensioned to accommodate 512 separate mine airways and junctions, and it contains all the features and capabilities of the original version. It has successfully analyzed all the ventilation networks tested, including a very large commercial mine (404 airways, 237 junctions, and 5 fans). In all cases the PC version produced practically identical results as obtained from the mainframe computer. In all respects, the PC version performed the same as the mainframe version with the exception of execution speed When a numerical coprocessor is employed, execution time can be reduced by more than 50%.

Jan 1, 1989

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By A. E. Raddatz

In an attempt to develop technology to use domestic resources in place of imported bauxita, the Bureau of Mines investigated sulfurous acid leaching to extract alumina from kaolin. The process consists of leaching the calcined kaolin with a 30 wt-pct S02 solution at 60° C and 160 psig for 17 hours, fil¬tering the leach slurry, precipitating monobasic aluminum sulfite from the filtrate at 110° C and 60 psig, a& decomposing the sulfite in the spent liq¬uor at 150° C and 55 psig to produce crude alumina. Purification of the crude alumina was accomplished using a modified Bayer process. Results from closed-circuit tests employing the sulfurous acid process showed that overall extraction of alumina from kaolin was 67 pct. Production of 1 ton of alumina would require 3.6 tons of calcined kaolin, 0.7 ton of sul¬fur dioxide, and 8.4 tons of water. After purification by a modified Bayer process, the alumina product contained the following; impurities, expressed in weight-percent: Fa203, 0.009; S, 3.6; Si02, 0.07; Ti02, 0.002; K20, 0.017; and P205, 0.03.

Jan 1, 1981

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By Robert J. Timko

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just inby the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized pro-gram, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 2010

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

By Frederick C. Trutt

This report is intended as a reference for personnel interested in the computer anlaysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures described include the Newton-Raphson iterative technique for the analysis of normal operation as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults. During program development, strict attention has been given to the inclusion of core and/or time saving techniques such that these algorithms may be implemented on small as well as large computers. Program languages include FORTRAN IV for batch processing applications and APL or BASIC for interactive applications.

Jan 1, 1981

By Robert A. Clifton

This Bureau of Mines report discusses the mineralogy of zeolites, the properties that make them commercially valuable, the conditions of formation of both natural and synthetic zeolites, and present and potential markets.

Jan 1, 1987

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"FOREWORDFerrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade are in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory,and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the were discussed in the foreword of the first paper of this series, Report of Investigations 3606 Manganese Investigations. 1. Concentration of Manganese Ores,from the Drum Mountain District, Utah, by S. R. J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By Wilson Blake

This report presents the results of a 7-year Bureau of Mines program to review, revise, and make an effective engineering tool of the microseismic method of determining the stability of rock structures. The program consisted of developing new microseismic equipment and data analysis techniques and extensive field investigations to demonstrate the effectiveness and potential of the broad-band microseismic method. The guidelines for choosing the components of a microseismic system are presented along with approximate cost figures. Different microseismic systems are discussed, including completely automated systems. Procedures for conducting microseismic investigations and analyzing microseismic data are discussed in detail. Field situations which show the full value of the microseismic technique as an engineering tool are described.

Jan 1, 1974

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between, the Coordinating Fuel Research (C.F.R.) Committee of the Coordinating Research Council (C.R.C.) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.-4/ Further reports have been issued describing motor gasolines sold during the succeeding summers and winters to the summer of 1941 and during the winter of 1942-43 and the summer of 1943 5/ No reports were made on motor gasolines sold during the winter of 1,) 41-42 and during the summer of 1942. The present report presents analytical data for 1,356 samples, representing the products of approximately 103 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines - and each group has been averaged separately. The number of samples, items and brands comprising each group is as follows: Regular-price, 770 samples, 286 items, and 94 brands; premium-price, 537 samples, 236 items, and 72 brands; third-grade, 49 samples, 31 items, and 18 brands. The meanings of these terms as used in the surveys are as follows:"

May 1, 1944

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947