Search Documents

By P. R. Tisot

This report discusses the waxes made from shale-oil wax distillate, a specific fraction obtained- from crude shale oil. The plate wax crystals Were exceptionally well suited to solvent extraction. Methyl ethyl ketone was the preferred dewaxing solvent.' The quantity of wax recovered at 32°F was 18.8 percent of the wax distillate, or 6.6 percent of the crude shale oil. The laboratory batch processes used for separating the wax from the distillate and subsequent refining were based .upon conventional petroleum methods. Three grades of shale-oil waxes were made and designated as crude, semirefined, and fully refined. The solvent-extracted wax consisted mainly of paraffin and olefin hydrocarbons. The physical Properties of the fully refined shale-oil wax were the same as er corresponded closely to those of Billy refined petroleum paraffin wax. Inasmuch as the crude and semirefined shale-oil waxes can be separated and refined in much the same manner as petroleum waxes, the cest of manufacture should be about equal to that for making petroleum paraffin wax. The cast of making a fully refined shale oil wax will be somewhat greater than for making .a fully refined petroleum paraffin, due to the loss of the oleofinic material from the shale-oil wax by acid treatment and the increased quantity of acid required for its removal. An analytical method for the determination of wax in shale-oil dietillates, a list of the physical properties that wore determined for the waxes, and the method for testing those properties are given in the appendix to this report

Jan 1, 1950

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By F. W. Davis

For some years this subject has been of interest to metallurgists. Previous to the War some work was done in :Belgium. on the enrich.ntSnt of the blast with oxygen i.."'l. connection with the smelting of iron orei.; in the blast furnace. In the United States, the late .J. E. ,Joh."lson, .Jr., \ve.s :interested in the possible use of 0J1.:ygen for metallurgical operations ar.:i cerried on some experic:.ental work along these lines pre..,,-ious to his de.e.hft Dr. F. G. Cottrell, formerly Director of the :Bureau of Mines, De7?,H''(;:,-of,,:a:t: of the Interior, and now Direc'cor of the Fixed lifi trogen Itesearc:l-1 La -:c r;a.-o='Y, Depart­ment of .Agriculture, first directed. the Eurec:ru 1 s attention to this subject. When it first began this work, the Director of the Burea.t1. of Mines, beca11se of his interest in this investigatio:::i, asked :Mr. M. H. Roberts: Vice-President of the FraU:din Railway Supply Company to select an Advisory Corr:nittee to work with the BJ::eau on tl1is subject; it also asked Mx-. Robez·ts to act as Cha.irman of this C<)1.,_1l!lHtce. T!le personneJ. of the Comrnitee which was selected. by r. Roberts is as follows:

Jul 1, 1923

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team&apos;s protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)&apos; with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By J. M. Kuchta

The Bureau of Mines used laminar hot air jets of l/8- to 3/4-inch diam-eter to determine the hot gas ignition temperatures of various combustible vapor-air mixtures. The combustibles were n-hexane, n-octane, n-decane, a hydrocarbon jet fuel (JP-6), and an adipate ester aircraft engine oil (MIL-L- 7808). Minimum ignition temperatures occurred at a fuel to air weight ratio of about 0.5 and were not greatly sensitive to variations of fuel concentra¬tion. Moderate variations of jet velocity also had little influence on these ignition temperatures. However, these temperatures decreased with increase in heat source dimensions (jet diameter). The hot gas ignition temperatures of the combustibles were not necessarily much greater than corresponding autoignition and wire ignition temperatures when the size (,F the heat source and the ignition criterion were the same.

Jan 1, 1966

By J. J. Forbes

Ventilation is the most important safety factor in the production of coal because on it depends the safety, health, and efficiency of those who work underground. Without adequate and efficient means of supplying fresh air to the working faces, mining could not have advanced as it has. The extent of the workings, the increase in mechanization, and the increasing use of electricity are largely responsible for changes in methods of ventialtion. Ventilation in the early, days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings: Later the furnace was introduced for the purpose of increasing the quantity of air in circulation. Mines continued to become larger, their output increased, men were employed in greater numbers, and more fresh coal surfaces were exposed. Coal beds near the surface, and practically free from explosive gas became exhausted, and deeper beds that liberated methane were opened as development advanced. Mechanical ventilation became necessary and was first accomplished by disc-type steam driven fans she old-.fashioned steam driven disc fan has generally been supplanted by the powerful electrically operated centrifugal fans in use at modern coal mines. In order to be secure against gas explosions and provide ample fresh air for persons employed in large coal mines, air must be conducted through the mine to all working places and to all other unsealed parts of the mince in sufficient quantities to dilute and render harmless all dangerous and noxious gases.

Jan 1, 1929

By Charles L. Harnes

A mineral pigment is a colored substance dug from the ground, which after treatment can be mixed with a drying oil to form a paint. Not all colored earths, however, can be made into satisfactory pigment. Much depends upon the attractiveness and uniformity of the color and the ease of purification. Mineral pigments are distinguished from chemical pigments by a difference in origin and treatment. Chemical pigments are not found ready-made in the earth but must be synthesized or otherwise obtained from other compounds or elements; for example, cadmium yellow, a chemical pigment, is precipitated from a solution of cadmium chloride, hydrochloric acid, and sodium sulfide.

Jan 1, 1942

By Kung-Lee Wang

This Bureau of Mines study illustrates the economic significance of the Florida phosphate industry to the State and to the Nation. Environmental considerations related to phosphate industry activity are discussed briefly. Based on forecasts of Florida phosphate production in 1975, and using 1972 dollars, regional and national output value, income, and employment created by the phosphate industry were estimated for 1975. State and Federal government tax revenues generated by the phosphate industry, are also measured. Further, the concentrated impact of the phosphate industry on certain Florida areas and on regional industries is examined. Finally, the phosphate industry&apos;s importance to the U.S. balance of payments, U.S. agricultural production, and the Frasch sulfur industry is considered, in addition to byproduct fluorine, and potential byproduct uranium from fertilizer manufacturing.

Jan 1, 1974

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By Oliver Bowles

The exingencies of a world war have brought home to the American public, especially the people of the. Eastern States, the urgent need for conserving fuel. Transportation problems in the East have created an unprecedented situation wherein fuel-oil supplies are greatly restricted, and the consequent increase in demand for coal further complicates the problem of transporting and storing that commodity. People should awaken to the need for utilizing every possibly means of conserving to fuel, even to the extent of reducing the temperature in their homes.

Jan 1, 1942

By G. St. J. Perrott, N. A. Tolch

"The testing of explosives for permissibility for use in coal mines was begun by the technologic branch of the United States Geologic Survey in February, 1909, and continued by the United States Bureau of Mines from July, 1910; this testing has been carried on from year to year as the explosives were submitted by manufacturers. As a result of these many years of testing for permissibility a large amount of data has accumulated regarding the characteristics of permissible explosives. The manufacturer expects a sample of explosive submitted for test to meet the requirements for permissibility, otherwise the sample would not be submitted. However, in spite of the careful regulation and preparation of the formulas a certain percentage of explosives fails to pass the gallery tests. It is therefore interesting to note the proportion of failures at the gallery for a given composition of explosive. The fact should be emphasized that this discussion deals with all explosives submitted for test, both those which passed the tests and those which failed to pass. Explosives that failed to pass the tests were never designated as permissible explosives and have never appeared on any list of explosives permissible for use in coal mines.The Bureau of Mines classifies permissible explosives in two ways, according to the quantity of poisonous gases produced and according to the characteristic ingredient of the explosive.4 In this paper only two types of the latter classification are considered, as follows:"

Dec 1, 1929

By H. H. Dewing

The U.S. Bureau of Mines characterized Hg-containing wastes and used a thermal-desorption process to remove and recover the contained Hg. The wastes were generated by an electrical-parts plant engaged in the assembly of Hg-containing switches and contained phenolic resins and paper insulating materials mixed with soil. The average Hg content was 396 ppm. Numerous characterization tests showed the Hg was tightly absorbed and could not be removed or concentrated by leaching or gravity separation techniques. Laboratory retort tests showed the Hg content reduced to < 16 ppm in 2 h at 400 °C; rotary-kiln, thermal-desorption tests required 4 h at 450 °C. Airflow through the retort im¬proved thermal-desorption efficiency, but vacuum operation only slightly reduced the temperature needed for thermal desorption. Offgases from decomposition of organic materials were burned in a high-temperature afterburner and subsequently cooled in a heat exchanger to condense water vapor. Finally, the Hg vapor was condensed and absorbed from the offgas by activated charcoal. Mercury recovery was over 99.99 pct of the desorbed Hg. Thermal-desorption processes have had wide application to many Hg-containing wastes, and historical experience in Hg mining has demonstrated its potential cost effectiveness.

Jan 1, 2010

By BUREAU OF MINES

Atentative Draft of a standard smoke abatement ordinance has been prepared by a joint committee made up of representatives of the American Society of Heating and Ventilating Engineers, the Stoler Mamufacturers Association, the American Civic association, and the Fuels Division of the American Society of Mechanical Engineers. The Committee is desirous of obtaining helpful criticism and suggestions about this ordinance, which should be mailed to the chairman, Dr. O. P. Hooi, Bureau of lines, ashington, D. C. Te personnel of the committee is as follows: Dr. O. P. Hood, chairman, and Henry Kreisinger, representing the Fuels Division of the American Society of Mechanical Engineers; P. J. Dougherty, representing the American Society of Heating and Ventilating Engineers; Lloyd R. Stowe, representing the Stoker Mam- facturers Association; Everett L. Hillard, representing the American Civic Ascociation; and Osborn Monnett and Harry 3. Meller, members at large.

Mar 1, 1930

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968