Search Documents

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By E. L. Rawlins

A previous report4 has explained that pipe lines for the transmission of natural gas should be buried to minimize temperature fluctuations because when excessive the latter decrease accuracy in measuring gas volume and increase leakage of gas due to expansion and contraction in the pipe joints. These effects are governed by the rapidity of the temperature fluctuations and by the total variation over a period of time. The temperature of gas flowing through a pipe line depends to a large extent, upon the temperature of the ground adjacent to the pipe; hence, fluctuation of the ground temperatures at various depths determines the economic depth at which pipe lines should be buried. Scope and Purpose of Report This report covers a record of the daily atmospheric temperature fluctuations at Bartlesville, Okla., for 12 months and a-similar concurrent record of the temperature variation 1, 2, 3, and 4 feet below the surface of the ground.

Jan 1, 1928

By Oliver Bowles

From the most remote periods of civilization, stone Las been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns) or single markers to great obelisks and pyramid or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1050 at a cost estimated at a: high as $50,000,000, and it is today an object of unusual attraction for travelers. Other magnificent memorials, both ancient and modern, are to be found in many lands. Memorials of varying design have characterized the passing centuries and have found an important place in the New World. In early days, monuments were chiefly imported into America, but gradually an extensive memorial stone-manufacturing industry developed on this side of the Atlantic. Sales value of domestic memorials, f.o.b. quarry or mill, attained a maximum of $17,488,755 in 1920, and retail sales, of course, reached a much higher figure. Modest markers and tombstones are to be found in almost every rural community in the United States, and there are many elaborate and costly monuments in and near urban centers.

Jan 1, 1938

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

By Ann G. Kim

The Bureau of Mines estimated the methane content of a coal, which depends primarily upon rank and pressure, from the adsorption equation V =kpn, where k and n are constants related to rank. By incorporating corrections for moisture, ash, and temperature, and estimating pressure and temperature as a function of depth, the methane content of coal in place can be estimated from the following equation: [ ] Values calculated with this equation generally are in reasonable agreement with direct determinations. By assuming a standard moisture and ash content, and using the hydrostatic head to estimate pressure, a graph of rank and depth versus gas content was constructed. Although estimated values were consistently high for several high-volatile bituminous coals from an area where the pressure is known to be less than hydrostatic, the estimated methane content for most coals shows reasonable agreement with values determined by the direct method.

Jan 1, 1977

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremo1ite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

By C. O. Hawk

As an exploratory effort to produce useful products from coal by a new path, the Bureau has made a few experiments on the fast heating of finely ground coal particles by irradiation with a flash of high intensity light. The flash was produced by an electrical discharge at high voltage through a xenon-filled tube. The flashes lasted from 2 to 3 milliseconds. The reaction took place in small sample tubes, ½ inch-dimeter by 4 inches long, and with small amounts of coal (total amount charged 0.1 gram, probable effective amount not more than 20 milligrams). Average particle size of the coal, estimated on a numerical basis, was 20 microns. Temperatures reached were evidently quite high, because all products obtained in quantity were characteristic of high temperature pyrolysis. Apparently, conversion of the coal was extensive where isolated particles received the full benefit of a flash. It seems particularly significant that acetylene was present in appreciable amounts--comprising almost 3 percent of the total gaseous product in one case. This is good evidence of a short heating period to very high temperature (well above 1,000° C) followed by rapid quenching. Although the results are interesting, they do not suggest any immediate practical application.

Jan 1, 1963

By I. O. Salyer

This research was conducted with the objective of suppressing the respirable dust in coal mines by foam application. A formulation was developed for making a water-based, high-expansion, and limited stability foam. A horizontal boring machine was used as a laboratory coal mining model for generating coal dust. A modified laboratory foam generator was built. Foam was applied directly to the point at which dust was being formed by the cutter of the boring machine working against a block of coal. Coal dust was sampled with an impinger and analyzed for the particle count and particle size distribution. Coal dust suppression test results on freshly generated dust have demonstrated very clearly that in laboratory scale experiments over 90% of the respirable coal dust can be suppressed by foam. These tests were run when initial coal du t concentrations were 10 and 70 million particles per cubic foot (mppcf).

Jan 1, 1970

By G. A. Apell

Completion of 18 churn-drill holes totaling 2,218 feet and 3 diamond-drill holes aggregating 421.5 feet of drilling in the M.C. mine area, near Truman, Wis., provided information indicating the existence and trend of a zone of zinc mineralization extending for 1,000 feet west of the old M. C. shaft.

Jan 1, 1949

By Fred N. Kissell

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By James A. West

The South Asian countries of India, Pakistan, Afghanistan, Ceylon, Nepal, Bhutan, and Sikkim arc to varying-degrees just beginning to achieve significant economic and industrial development. These countries are richly endowed with certain mineral resources, and development of these resources is being accelerated. In 1965, the mineral industry remained a relatively small sector of the region's economy, accounting for only about 1 percent of its estimated gross national product of $62,528 million. Nevertheless, the estimated $630 million total value of minerals produced in South Asia during 1965 represented an increase of nearly 15 percent t over that of 1964. India continued as the dominant mineral producer of the region, accounting for 85 percent of the total value of all minerals produced ill 1965. India increased its output of iron ore, manganese, mica, coal, and petroleum. Pakistan accounted for 13 percent of the value of the region's output and recorded increased output of iron ore, chromite, coal, natural gas, and most other minerals. The small mineral industry of Ceylon attained remarkable growth in the production of ilmenite, graphite, and gem stones. The mineral industry of Afghanistan remained relatively insignificant, although development of large known resources of natural gas was continued, Nepal, Bhutan, and Sikkim produced no commercially significant quantities of minerals in 1965.

Jan 1, 1967

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

By B. H. Eccleston

Experimental data were obtained from two medium-duty diesel engines derated to qualify for use in underground mines. Gaseous and particulate emissions from these engines were measured and results provide information on the effect of exhaust treatment devices on the emissions. The devices in the study were a catalyst, a particulate trap, and an exhaust gas cooler of the water scrubber type. Emission levels of carbon monoxide and hydrocarbons were observed to be very low in comparison with emission levels of comparable engines in full-rated operation. Oxides of nitrogen and benzo(a)pyrene content of the exhaust also were found to be somewhat low in comparison with previous findings. For particulate reduction, the combination of a particulate trap and a scrubber was observed to be the most effective combination tried; in some cases, over 60 pct particulate reduction was effected by the trap-scrubber combination.

Jan 1, 1981

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all minerals to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of forces applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective.

Jan 1, 1932

By Frank J. Wiebelt

The Mohawk lead-zinc mining in San Bernardino County, Calif., was examined by D. W. Butnor, an engineer or the Bureau of Mines, at the request of Dunton, Ray, and Greenwood, leaseholders. Current operations were on a marginal economic basis, and government aid was sought in an endeavor to outline ore reserves so that production might be maintained.

Jan 1, 1949

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974