Search Documents

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine's heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By Van Zyl Brink

A longwall-based coal mine in Australia, referred to in this paper as AusMine Colliery, experienced windblasts resulting from goaf falls. Windblasts were the cause of serious injuries and threatened the continued operation of the mine. A microseismic early warning system was installed and a significant success rate in providing early warning of large roof instability resulting in high velocity windblasts, has been achieved. Early warning of goafing is accepted as an operational tool on the mine. Severe demands are placed on the operator in terms of 'real time' interpretation. The development of an expert system allowed for a probabilistic approach to achieve automatic alarms. This paper will quantify the success, failure and false alarm rates achieved by manual operation and automatic expert system-based decisions making, respectively.

Jan 1, 2002

By A. C. Beaulieu

CITY OF EDMONTON Rate of Growth The City of Edmonton has been classed by some economists as being the most progressive City in Canada since the early 50's. The high rise buildings that are changing Edmonton's skyline, the rapidly expanding sewer and water network, and the proposed rapid transit system all indicate the requirements of an ever expanding City. Edmonton, the core of Canada's Energy Empire is the country's seventh largest metropolitan area. Bisected by the 22 mile long park of its magnificent river valley, it sits in the midst of the 50,000 sq miles of riches that have created it. Underneath the City, however, extending down for thousands of feet and encircling it for a radius of scores of miles, lies a fabulous store of petroleum wealth. By the early 1940's, based upon the needs of the farming areas, accompanied by some small exploitation of coal and timber, Edmonton grew to 100,000 people. Then in a short space of 20 years Edmonton shot up to be a city of 450,000. Figure 1 (Slide No. 1) indicates the population growth in the City of Edmonton and the Census Metropolitan Area from 1906 to 1971.

Jan 1, 1997

By P. K. Ackerman, F. F. Aplan, G. H. Harris, R. R. Klimpel

Fourteen reagents that are potentially capable of chelating with a metal ion on the surface of the major copper sulfide minerals and pyrite were evaluated for their effectiveness in floating these sulfides. The reagents studied fall into the classes of mercaptobenzole mutations, thiouronium, thionocarbamates, thiourea, imidazole mutations, oximes, hydroxyquinoline and xanthogen formate. The best overall copper sulfide collector was an imidazoline (1-Hydoxyethyl - 2-Heptadecenyl), but it also proved to be an excellent collector for pyrite. Its potency as a pyrite collector can be reduced by structural alteration, but at some loss in its collecting power for the copper sulfides. The effectiveness of many of these potential collectors can be changed by minor alterations to the collector molecule and, to a lesser extent, by pH adjustment. The general order of mineral floatability with these reagents is chalcopyrite = chalcocite > covellite =bornite >> pyrite. The flotation of malachite is generally similar to that of the copper sulfides, indicating the special effectiveness of copper in the crystal lattice for collector attachment.

Jan 1, 2000

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By Gretchen K. Hoffman, George S. Austin

Soil amendments or soil conditioners generally carry the con- notation of being useful for problem soils or soils needing special treatments to produce maximum yields. Many different materials have been utilized, both inorganic and organic. Only the most commonly used and those that appear to have potential to become commonly used will be discussed. Soil productivity depends on many factors. Soil amendments mainly modify physical characteristics and microbial action, and/or change the pH of a soil, rather than directly supplying plant nutrients. They give soil the needed physical properties to allow plant growth, fight erosion, or save water. Some soil amendments provide nutrients in addition to altering the physical, biological, or chemical characteristics of soil. The term "soil amendment," as it is used by Soil Science Society of America, allows soil amendments to be materials other than those used primarily as fertilizers (Anon.,1987). Soil amendments as fertilizers of any type will not be considered here because this aspect is more relevant to the previous chapter entitled "Agricultural Materials: Fertilizers" in this volume. Several inorganic soil amendments have been used since the early 20th century to alter the character of soil: limestone, lime, and similar calcium-rich carbonates and oxides for acid soils, and calcium sulfate (gypsum) and native or uncombined sulfur for alkaline soils. The use of these amendments (limestone, lime, gypsum, and sulfur) or their equivalents has been studied and documented in many basic soils tests (McCaslin and Boyle, 1980). Perlite and vermiculite are considered in separate chapters and only a brief statement of their use as soil conditioners will be made in this chapter. Peat is the principal natural organic soil amendment, but manure, both as a fertilizer and soil conditioner, is used in every part of the world. In less-developed countries, manure is the primary soil fertilizerlconditioner. An organic-rich material designated as "humate" has been marketed as a soil amendment for many years and will be addressed in this paper. Other materials are discussed by the Soil Science Society of America in its Special Publication 7, "Soil Conditioners" (Stewart, 1975). They include bitumen emulsion, polyacrylamide, polyvinyl acetate, polyvinyl alcohol, bentonite, nonionic surfactants, and natural mulches. Zeolites can be added to the list of miscellaneous soil amendments (McCaslin and Boyle, 1980), as can calcium chloride (Pressler and Pelham, 1985), sulfuric acid, ferric and ferrous sulfate, aluminum sulfate, ammonium polysulfide, calcium polysulfide, and ammonium bisulfite (Stromberg and Tisdale, 1979). Sludge will not be considered as a soil amendment because it has properties more consistent with fertilizers. All these "other materials" account for a very small amount of the volume and value of soil amendments used and will be only briefly discussed.

Jan 1, 1994

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By C. B. Manula

The total systems model for underground coal mine planning and design (Master Design Simulator) is a set of computer programs which encompasses a realistic reproduction of the interaction among the geological, environmental, equipment, methods, and the health and safety aspects of the mining plan (Manula, Rivell, and Ramani, 1975). The total system includes nine major subsystems: geology and reserves, methane generator, roof support, subsidence, production, rail haulage, cost, water generator, and ventilation (Fig. 1). The subsystems themselves are divided into two categories based on the frequency with which they are executed: (1) event-oriented subsystems are executed either independently or at discrete intervals when certain specific events occur; and (2) dynamic subsystems function interactively during the production cycle, transferring data to or requesting data from event-oriented subsystems only when specific events occur (Fig. 2). Each subsystem has been tested and validated independently (Ramani, White, and Sutton, 1974; Ramani and Owili-Eger, 1974; Manula, Mozumdar, and Jeng, 1974a; Manula, Mozumdar, and Jeng, 1974b; Manula, et al., 1974; Manula, Rivell, and Sanford, 1974; Ramani, McClay, and Burgos, 1975; Manula and Owili-Eger, 1975; and Ramani, Owili-Eger, and Manula, 1975).

Jan 1, 1979

By M. M. Ragin, B. J. Scheiner

The US Bureau of Mines (USBM) has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. It was found that at a given polymer concentration, there were an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By Dick Lewis

The Misima deposit is on Misima Island in the Lousaide Archipelago, 240 km east-southeast of the Papua New Guinea mainland, and 600 km east of Port Morseby. Misima is a narrow mountainous island 40 km long and up to 10 km wide. The highest point is 1035 m above sea level. Gold mineralization is restricted to the eastern and less rugged third of the island. The Melanesian population lives in coastal villages. Subsistence agriculture is the main activity, although copra and cocoa are grown in plantations on the eastern and southern coasts. Prior to 1950, mining was important in the economy of the island. Climate is tropical, with little seasonal variation in temperature or rainfall. Tropical cyclones occur about every 10 years (Fig. 1).

Jan 1, 1990

By J. Stachurski, N. A. Abdel-Khalek

Laboratory Potation tests were carried out on six Polish coal samples of different rank. Each coal sample was screened into seven size fractions. The floatability of size- by-size for various size ranges for different samples was investigated as well as for the original samples. The results showed that in flotation of size-by-size, the intermediate sizes varied with the rank of the coal. Entrainment was shown to be an important mechanism in the recovery of fine particles in flotation of the original samples.

Jan 1, 1991

By Daniel McConvey

Who is the Investor? -Mainly institutional, including resource funds, other mutual funds and pension funds. -Some hedge funds. -Retail investors. -How important is the reserve disclosure to these investors? -Do these investors know the difference between a reserve and a resource?

Jan 1, 2003

By R. L. Pozzo, A. S. Malicsi, I. Iwasaki

The electrochemical nature of mineral-grinding media interaction in the wet grinding of one and two sulfide mineral ores was investigated with regard to the flotation behaviors of the minerals. Two iron sulfides (pyrite and pyrrhorite) and mild steel were used to represent the sulfide minerals and the grinding media, respectively. Galvanic currents in two- and three-electrode combinations under abrasive and non abrasive conditions were correlated with the floatabilities of these minerals under corresponding conditions.

Jan 1, 1991

By Daniel Hodouin, Claude Bazin, Sami Makni

A method is proposed to perform on-line data adjustment and inference of unmeasured variables, using measured flowrates and on-stream assays in mineral processing plants. The algorithm minimizes a weighted sum of squared residuals of the measured variables and squared species imbalances around the flowsheet nodes. The method is based on a trade-off between the material transient accumulation, evaluated by the imbalances, and the data inaccuracies, evaluated by the residuals (i.e. the adjustments brought to the measured values). A recursive algorithm is developed for on-line implementation of the method. It is a real-time extension of the hierarchical method for balancing steady-state data for bilinear mass conservation constraints. An illustration for a simulated flotation circuit is provided.

Jan 1, 1995

By K. N. Han, Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions was investigated using a rotating disc. Oxygen was used as an oxidant. The effects of the alloy composition, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics were studied. Three silver/copper alloys (containing 76.7, 46.9 and 24.1% silver) were used in this study. The rates of dissolution for these alloys were compared to that of pure silver and copper under the same testing conditions. Emphasis was given to the galvanic effect on the overall dissolution rates.

Jan 1, 1995

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By K. Wangerud, B. S. Caruso

A water-balance model with deterministic and stochastic components was developed and used for the Gilt Edge Mine Superfund Site in South Dakota. The model was developed to evaluate the risks of contaminated runoff discharging to surface waters based on assumed water treatment plant (WTP) rates, for different remedial alternatives. The objectives of the modeling were to use a stochastic approach for the analysis of precipitation based on historic records and to make a probabilistic estimation of annual and monthly runoff from disturbed/mining activity areas that now require, or will need, treatment at the WTP, water storage and changes in a major pit, and risk of contaminated water bypass of the WTP to a downstream drainage. Subareas/source areas generating contaminated runoff requiring treatment were delineated. A simple water-balance model was used based on precipitation inputs and evapotranspiration and groundwater losses. Annual and monthly precipitation records for Lead, South Dakota, were used to estimate precipitation at the mine site. A lognormal distribution was estimated for monthly precipitation. The stochastic software package/ Excel add-in "@Risk" was used to generate random monthly precipitation values using a Monte Carlo method based on the distributions. The average annual and monthly distribution of pan and lake evaporation and of groundwater losses were also estimated for the site. Stochastic outputs from the model for the end of each month and year included contaminated runoff requiring treatment, water storage in mine pits and the risk of WTP bypass given different assumed WTP rates. The probability of the time required to dewater the pits was also modeled.

Jan 1, 2003

By J. D. Miller, C. L. Lin

A PC, image-based, on-line instrument for measuring coarse particle size on a conveyor belt is under development. The hardware and software required to implement such a system are discussed, including the interface for the special image-acquisition hardware. The system concept is given with examples to illustrate the step-by-step procedure for the implementation of image-processing algorithms.

Jan 1, 1994

By R. L. White

Classification of Mills Mills may be classified under four categories that relate to the type of action utilized to grind the material: Tumbling. The most important of these to the minerals processing industry are tumbling mills. Grinding media is actuated in a free¬form pattern in a rotating drum causing it to tumble, material being ground passing through the tumbling media. Work is done by a combi¬nation of attrition and impact. Impact. Grinding media is actuated in a distinctive pattern so that it impacts the material being ground. Work is done by impact. Roller. Grinding media is actuated in a distinctive pattern, mate¬rial being ground passing under or between the media. Work is done by compression. Fluid Energy. There is no grinding media as such. Energy is imparted to the material by transfer of kinetic energy from the fluid to the material. Grinding is accomplished by interparticle impact and attrition. Tumbling Mitts The main physical arrangement consists of a lined cylindrical drum mounted on trunnion bearings driven by a ring gear and pinion, in turn connected directly or through a reducer to the electric motor. Variations to this general arrangement include: (1) Drum mounted on rollers instead of trunnions. (2) Bearings on the drum directly, not on trunnions. (3) Utilization of multiple pinions on the gear. (4) Trunnion-type drive arrangement through a gear reducer with¬out the use of a ring gear. (5) Motor rotor mounted directly on the drum with stator around the drum, thus eliminating the gearing. The drum consists of a shell and heads lined with replaceable liners of various types and configurations. Various types of tumbling mills are tabulated; illustrations of some are shown. The types are so designed for specific purposes. Media utilized include steel rods, balls, or rock of the same material as being ground or of special material in the instance where iron contami¬nation is detrimental (see Figs. 9 and 10 and Table 2). Impact Mills Although there may be some overlapping of interpretation of terms, impact mills are considered those in which the media is actuated in a distinctive manner, at relatively high speed, impacting the material to be ground. There is an overlapping also in what may be considered to be crushing equipment rather than grinding equipment. Hammer Mill or Impactor. Material is fed into the equipment; inside hammers of impactors revolve at a high speed, breaking the material on impact with the hammers (see Fig. 11). Material is also thrown against the periphery of the mill, causing impact grinding to occur. Equipment is normally lined with replaceable abrasive resis¬tant metal; hammers are also

Jan 1, 1985