Search Documents

By F. Leschhorn

A computer model for long-term production scheduling is presented. By combination of different operations research algorithms it has been possible to design a system which is able to solve difficult long-term planning problems. The practical application of the model by a west-german hard coal mine is shown. It is proven that the EDP-model provides substantial support to the planning engineer by solving complex optimization problems.

Jan 1, 1989

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By D. Butler

Lateral density changes in the subsurface cause a change in the vertical pull of gravity at the surface. By very accurate measurement of gravity and the practical application of common sense, a microgravity survey can sometimes detect natural or man-made voids, bedrock profiles, and geologic structures of engineering interest. This paper will give some practical guidelines for the application of microgravity surveying. Emphasis in many papers (Blizkovsky, 1979, Fajklewicz, 1983) has been on the anomaly size: herein emphasis will be placed on detectability and signal-to-noise ratios. First, some easy to use curves for anomaly valuation are adapted from Arzi (1974). Secondly, the predictable noise sources are discussed. Thirdly, representative models of abandoned underground workings are evaluated for microgravity surveying given the probable noise in the survey results.

Jan 1, 1988

By E. B. McNew, J. M. Barnes, A. E. Torma

The applicability of biosorbent materials for the removal of uranium and other heavy metals from synthetic and actual uranium mil 1 tailing (UMT) solutions has been investigated. The biosorbent materials used in this study were barium loaded beads of alginate, alginate-dextran sulfate, alginate-carrageenan, and alginate-xanthan gum. These studies were performed in stirred vessels and packed columns. It was observed that 100 percent of the uranium could be removed from a synthetic solution following 2 hours of contact time in a stirred vessel, and 80-100% of U, V, Mo, Mn, Sr, and Zn could be removed from a UMT effluent solution with a packed column. Kinetic evaluations were performed, using a generalized rate equation, on the biosorption of uranium with these barium loaded beads.

Jan 1, 1992

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

By Bruce B. Redpath

Single-charge cratering tests can provide a direct measure of the powder factor necessary for achieving a desired effect in conventional blasting. If a desired blast effect, such as fragmentation or mound velocity, is produced by a single point-charge at a particular scaled depth of burial, then the cube of the reciprocal of that scaled depth is the appropriate powder factor for duplicating the effect in a conventional array of blast holes. Scaling formulas are presented that provide a link between point-, line- and plane-charge geometries, and which can be Apparent crater used for blast design. Mound and burden velocities from several sources are compared and several examples of blast design are given.

Jan 1, 1977

By K. Biswas

A finite-element algorithm was developed for an axisymmetric heat-transfer problem involving phase change. The finite-element treatment of the phase-change problem was dealt with by using the enthalpy method. The finite-element algorithm was subsequently applied to model the heat exchange between mine ventilation air and frozen ground in the presence of roof bolts in an underground mine with permafrost. This paper analyzes a single bolt in the problem domain with the convection boundaries at the roof level of the mine airway. A short-term study, comprising the evaluation of roof bolting (friction-anchored type), was conducted, and recommendations were made regarding the applicability of roof bolts as a support system for a given thermal condition.

Jan 1, 1996

By David Royston

Conventional straight-radial SAG mill pulp lifters suffer from incomplete discharge of the rock portion of the charge. The resulting backflow of undischarged rock limits pulp lifter performance and is the major source of wear in pulp lifters. Backflow is increased in pulp discharge cone systems where multiple channels converge towards the central diversion cone. This paper covers recent experience with pulp lifter and discharge cone design supported by a single particle motion model that illustrates the discharge and backflow characteristics of pulp lifters, including the impact of discharge cone configuration.

Jan 1, 2005

By S. K. Kawatra, S. T. Bagley, T. C. Eisele

The use of the bacteria Thiobacillus ferroxidans to catalyze pyrite dissolution in coal is well known, and recent investigations have shown that T. ferrooxidans are also capable of rapidly altering the pyrite surface to facilitate its removal from coal by froth flotation and oil agglomeration. However, the effect of reactor design on the bacterial leaching rate is poorly documented, and the ability of bacteria other than T. ferrooxidans to affect pyrite flotation has been unknown. In this study, the effect of a number of different microorganisms on the flotation of unoxidized pure mineral pyrite has been investigated, and it was shown that organisms other than T. ferrooxidans are also capable of depressing pyrite flotation. In addition, comparative studies of leaching in shake-flasks and pachuca tanks have shown that the pachuca tanks allow leaching to proceed to a greater degree and at a significantly accelerated rate.

Jan 1, 1989

By Patrick Linzer

The majority of existing models describing (methane) gas transport within, and liberation from, coal structures treat these as continua wherein two main gas flow modes (diffusive and Darcy permeable) prevail, and use finite difference techniques to generate solutions to the resulting multivariate parabolic partial differential equation(s). Isotropy and homogeneity in the physical and geometric coal structure properties are often assumed, and the existence of fundamental random fluctuations in these proper- ties is not catered for. The model proposed herein does not suffer these inadequacies, and its efficiency is enhanced by the replacement of the diffusion equation by an accurate approximation. Dynamic mining activity, gas contributions made by the geology surrounding the mining seam, goafing of overlying strata and the effects of induced strain are all taken into account.

Jan 1, 1995

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

By K. S. E. Forssberg, M. I. Hallin

In many cases, the reuse of process water in flotation plants is desirable both for plant operating reasons and for environmental protection. The main advantages are better housekeeping of fresh water and process chemicals together with the reduction of polluting species to the environment. There are however a number of problems involved in the use of recycled process water. The main problem is that recycling sometimes has a deterious effect on the process and can occur months after the start of water recycling. The Division of Mineral Processing of Luleå University of Technology has been conducting experiments on recycling of process water at various sulphide plants in Sweden for over ten years. The experiments have been carried out in pilot- and full industial scale, in collaboration with the mining companies operating the plants. Until 1988 investigations were carried out in four different sulphide plants. The objectives of the experiments were: first to document differences in the composition of the process water during recycling; secondly to investigate any changes in the pulp chemistry of the flotation circuits wich may be due to the influence of recycled water; and lastly to establish critical levels, if any. of the parameters measured. While conducting experiments of this kind several things have to be kept in mind. Normally, recycling is done by using tailings pond water as process water. This means that time effects are important, because of the time lag between water input in the tailings pond and the reclaim of that water back to the plant. As will be shown, the

Jan 1, 1989

By B. C. Flintoff

In general, process control systems in solid-solid separation have not evolved to the same level as in flotation circuit control. Perhaps one of the more significant contributing factors in this regard is the lack of suitable on-line analytical instrumentation. In spite of the obstacles, some interesting work has been done. This paper presents a review of current industrial control strategies in ore sorting, dense media separation, gravity separation and electrical and magnetic separation.

Jan 1, 1986

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

Building aggregates, basic materials for the construction industry, must be produced according to socio-economic and environmental sustainability principles, i.e. the three fundamental components of Sustainable Development. On this subject, an introductory discussion about the interpretation of these concepts in the field of mineral production and construction industry is first presented. As for the socio-economic aspect, aggregates are then illustrated as being essential resources for the development of the society, underlying that it is possible to understand their fundamental socio-economic role only through the analysis of the whole product life cycle, from production to end use and beyond. The same has to be done on the environmental side to assess the environmental impacts of aggregates: one should look for, not in the quarry phase only, but also in all the downstream activities of the construction process, including the use phase and beyond. Based on this approach, in the second part of the paper, the results of some investigations focused on eco-profiles of building aggregates, gathered through the application of LCA methodology are presented and discussed. In such a context, strengths and weaknesses of LCA indicators will be discussed, as well.

Jan 1, 2007

By T. Ruff, J. Steele

The lack of visibility near earthmoving equipment results in an average of five fatalities in U.S. surface mines each year. These accidents occur when a piece of equipment either strikes another vehicle or worker, or travels over the edge of an embankment. Researchers at the National Institute for Occupational Safety and Health have evaluated off-the-shelf proximity warning systems that sense obstacles near the equipment and provide an alarm to the operator. Limitations of existing systems have necessitated the development of new systems designed specifically for mining equipment, including a GPS-based proximity warning system and a computer-assisted stereovision system.

Jan 1, 2004

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By Mark D. Cocker

Georgia?s Coastal Plain contains important sediment-hosted deposits of kaolin, bauxite, heavy minerals, sand and gravel, silica sand, carbonate rocks, and fuller's earth. Genesis, location, size, and quality of these deposits are related to terrestrial, marginal-marine, and shallow-marine depositional environments that evolved during development of the southeastern North American continental margin. From the Cretaceous to Eocene, kaolin and aluminous sediments, which contained mica and feldspar, were deposited in marshes, ponds, and bays located in deltas or behind barrier islands or spits. In the Cretaceous sediments, subsequent, intensive, in situ chemical weathering converted mica and feldspar to kaolin. Kaolin eroded from deeply weathered granitic rocks in the Georgia Piedmont was deposited in Paleocene to Eocene sediments. Subaerial exposure during the Paleocene and Eocene desilicated kaolin sediments to form bauxite. Sand and gravel, silica sand, and heavy-mineral deposits are found in Cretaceous to Eocene fluvial and shoreline sediments, some of which are associated with the kaolin and bauxite deposits. Source areas, intensive chemical weathering in the source areas, transportation by the major river systems, and deposition of these clastic sediments in similar or nearby depositional environments are common elements in the genesis of these resources. Eocene fuller's-earth deposits are opaline claystones in near-shore to shelf-marine sediments, which overlie the kaolin-bearing strata. These claystones consist of montmorillonite and opal/ cristobalite derived from alteration of diatom frustules. Favorable ocean currents provided nutrients for extensive planktonic growth. Oligocene and Miocene carbonate rocks were deposited principally in shallow-marine embayments. Miocene fuller's- earth deposits in south-central Georgia and adjacent parts of Florida contain palygorskite that formed through alteration of montmorillonite/bentonite clays. Deposition and subsequent alteration occurred in shallow, brackish-water lagoons under relatively high temperature and subtropical conditions. Middle and late Miocene phosphorites were deposited on a shallow carbonate-shelf platform and were concentrated proximal to anticlinal highs. Numerous marine transgressions and regressions since the beginning of the Pleistocene resulted in shoreline detrital deposits containing aggregate sand, silica sand, and heavy minerals on the Coastal Plain and on the Continental Shelf. Major river systems transported sand and heavy minerals from source areas in the Piedmont and Upper Coastal Plain. Deltaic deposits of heavy minerals were redistributed and concentrated by longshore currents, shoreline processes, and aeolian processes. River-terrace sediments, correlative with the Pleistocene shoreline deposits, contain sand-and-gravel and silica-sand deposits. Aeolian dune sands are associated with both Pleistocene fluvial and shoreline detrital deposits.

Jan 1, 1999

By Malcolm Scoble, Sean Dessureault, Scott Dunbar

Budgets are key financial and behavior drivers for most businesses, including mining. Budgets are used to link strategic objectives to tactical decisions, to measure performance, and to provide basic financial planning. More accurate and pertinent budgets should result in improved strategic decision making and performance measures. This paper discusses how a process based production and cost database, based on activity based costing models and the one year production plan, can be used to create the annual budget for an operating mine as an Activity Based Budget (ABB). A case study is used to compare budgets derived from traditional methods and an ABB approach. It is evident that the ABB method is more accurate.

Jan 1, 2002

By J. K. Whyatt

A microcomputer controlled data acquisition system has been developed for automatic monitoring of underground instrumentation from a remote location. The system has been used extensively by Spokane Research Center personnel for monitoring rock instrumentation in shafts, drifts, and stopes in hardrock and coal mines, especially where instrument access is limited. Ruggedness was a major consideration in designing the underground portion of the system and it has performed satisfactorily under extreme environmental conditions, including temperatures to 1100 F, 100% humidity, and falling water. The major advantage of the system is that it multiplexes the data from 16 channels through a single twisted pair cable to the receiver, significantly reducing cabling requirements. This receiving station can be as far as 8,000 ft from the instruments without the addition of line drivers. The receiver maintains a data buffer with the latest scans, which is periodical 1 y accessed by a micro- computer, either locally or through a modem, that automatically records and reduces the data. Utilities allow on-site plotting of data and uploading of data to mainframe computers.

Jan 1, 1986