Search Documents

By Alan R. Grant

Interpretation of presently available geological information indicates that most of the periods of significant metal deposition in the Washington Cascades Range are, at least in part, genetically related to late Cretaceous -Tertiary intrusive episodes. Chemically, the most favorable environment for base metal deposition is high in potassium. Characterizing the advanced stages of these chemical alteration conditions are the silicate mineral assemblages orthoclase and/or secondary biotite. Wall rock alteration includes both deuteric and hydrothermal processes, the intensity of which primarily depends upon the degree of fracturing in the country rock prior to the introduction of secondary material. Broadly speaking, the primary physical controls for the distribution and concentration of sulfides appear to be a series of structural couples involving both northwest (paralleling regional trends) and northeast--striking systems. Meaningful base metal exploration in the Washington Cascades demands a basic understanding of the various geologic factors related to the distribution of the sulfide deposits. Any geologist contemplating Cascade work should be well grounded in the fundamental concepts of petrology and structure.as these constitute two of his most beneficial aids. The acquisition of the detailed data necessary for this understanding may seem a bit academic, yet it has been demonstrated in numerous instances that a fair economic appraisal of a particular property or mining district depends primarily upon the ability of the geologist to recognize the subtle environmental differences which could lead to the discovery of a major ore deposit.

Jan 1, 1971

By R. S. C. Rogers

Semiautogenous milling was the subject of 18 papers presented at the SME Fall Meeting in Albuquerque, NM. The process design and scale-up of SAG mills was discussed in several papers. These included a review of testing methods for the sizing of SAG mills by Barrett and Allan. Austin et al. presented an improved simulation model for SAG mill grinding, with model validity demonstrated against pilot plant SAG mill test results. Rogovin et al. presented some pilot plant results relating to the charge motion, hold-up, and particle size segregation in SAG mills. A number of papers described improvements achieved in operating SAG mill circuits. These included presentations by Dailey concerning mills at the National Steel Pellet Co., by Brown and Pipke concerning the Island Copper grinding circuit, by Lovering of Afton Mines Ltd., and by Bartrum et al. of Kidston Gold Mines Ltd. Bush and Hegerle of Amax also discussed SAG mill operations at the company's Henderson mill. They addressed the topics of SAG mill grinding economics. Other papers addressed the topics of SAG mill control (Vanderbeek et al. and Pennington), grinding media (Meulendyke et al.), liners (Kjos), and fabrication (Carr and Utley). The 1985 AIME Annual Meeting in New York featured four technical sessions concerning size reduction technology and practice. Papers involving fundamentals included one by Hinde describing simulation model usage for quantifying the classification and concentration of heavy minerals in grinding circuits. Another, by Rogers et al., discussed simulation models that were used as a design aid in evaluating screens versus hydrocyclones for fine grinding circuits. Arbiter discussed dimensional considerations in grinding mill design, and Schwechten and Schonert proposed the use of a high pressure roll mill as a means for reducing energy requirements in fine grinding. Internal classification in tumbling mills was the subject of a paper by Hogg and Rogovin. The mechanism of internal classification were identified and their effects illustrated. Simulation for the process design of ball mills was exemplified in a paper by Rogers, Austin, and Brame concerning phosphate grinding in laboratory to large diameter mills. The incorporation of liberation into size reduction models was the subject of papers by Austin et al., Herbst et al., and Choi et al. Gupta used simulations models to further investigate zero order fines production in ball and rod mills. Of the published literature, many articles on size reduction were published in various publications in 1985. Articles concerning ball mill grinding included an analysis of interstitial gas effects in dry grinding by Cottaar et al., an analysis of mill grinding noise by Watson, studies of factors affecting breakage rates in dry milling by Gupta et al., and in wet milling by Tangsathitkuchai and Austin. Austin and Klimpel presented two papers concerning ball wear and ball size distribution effects. Koka et al., and Gotsis et al., described recent developments concerning the Szego mill. A model for hammer milling circuits was described in papers by Gotsis et al. and Gotsis and Austin. Heim et al. reported on wet grinding in Perl mills, and Kuga et al. presented findings concerning pulverizing in a screen mill. Studies of grinding effects on particle surfaces were published by Meloy and Hofmann et al., and Scieszka proposed a technique to investigate pulverizing properties of coals. Austin and Rogers discussed factors of powder technology of significance in industrial size reduction in mills and crushers. (Space limitations preclude listing of references. A complete list is available from author.)

Jan 5, 1986

By G. R. Green

The centre of the mining operations of the International Nickel Company, Ontario Division is Sudbury, a city of 160,000 population located 240 miles northwest of Toronto (Fig. 1). Within thirty miles of this city and located around the rim of the geological formation known as the Sudbury Basin are the ten underground mines and one open pit operated by the Company (Fig. 2). There are also four developing mines, three in the Sudbury area and one at Shebandowan, near the city of Thunder Bay, Ontario and approximately 150 miles north east of Duluth, Minnesota. In 1971 the mines produced 22,800,000 tons, 20,600,000 tons from underground and the balance from open pits. Also located in the Sudbury District are facilities to extract and refine the metals contained in the ore. There is a nickel refinery located at Port Colborne on Lake Erie. An additional nickel refinery is under construction near Sudbury. Fifteen elements are recovered from the Sudbury ores, nickel, copper, iron, sulphur, gold, silver, cobalt, tellurium and the six platinum group metals, platinum, palladium, iridium, rhodium, ruthenium and osmium. In 1966 a major expansion program was undertaken to meet increasing market requirements. Coinciding as it did with a severe

Jan 1, 1972

By D. C. Panigrahi

The paper presents the application of Object Oriented Programming approach for the development of a network simulation model based on nodal pressure method using linearised flow equations. The convergence and computational efficiency of the algorithm have been investigated. Finally the paper re- ports the validation of this algorithm in actual field conditions.

Jan 1, 1996

By Xu Xiaohe, Zhou Jiandong, Luo Shihui, Zhang Liqun

Recently, the research and applications of ES (Expert Systern) have been put forward actively in many mining fields in China. After various ES applications or instances are introduced, the paper has especially focused on the exclusive properties of a mining system different from any other system and the problems of the existing mining ES applications. And a synthesis methodology has been introduced in order to develop a applicable ES application

Jan 1, 1996

By S. L. Zhu, Brij M. Moudgil, J. L. Pinault

Prompt neutron activation probe (PNAP) was evaluated to determine chemical composition of phosphate rock slurry in-situ. The technique was able to precisely analyze Ca, Si and H using a 252Cf source. Direct measurement of P and Mg was not accurate due to interference by the rare earth elements associated with the Florida Phosphate Rock. The solids loading, particle size distribution and flotation reagents present in the slurry had no significant effect on the accuracy of the measurements. The technique was found to be reliable also under industrial conditions.

Jan 1, 1993

By P. W. Johnson, H. Fan, S. B. Patton, T. Novak, R. L. Sanford

A computer model is presented that quantitatively uses the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasitication on the ventilation system in a longwall panel.

Jan 1, 1995

By J. W. Merks

Applied statistics provides scores of powerful tests and techniques that are widely used and abused in science and engineering. The variance is the basic measure for variability, precision and risk. The formulas for the variances of the arithmetic mean and the weighted average are derived from the variance of a general function, as defined in probability theory. The requirement of functional or mathematical independence in probability theory translates into the concept of degrees of freedom in applied statistics. Geostatistics is the only variant of statistics in which functional dependence and degrees of freedom are irrelevant. This paper examines whether such basic elements of probability and statistics can be ignored with impunity.

Jan 1, 1998

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992

By J. E. Chilton

Methanometers with catalytic heat- of-combustion sensors used in coal mines today will read low for flammable gases when oxygen (0,) concentrations are low or when methane (CH,) concentrations are greater than 10%. Thus, these methanometers may not be reliable during operations such as fire fighting or recovery of sealed mines. The U.S. Bureau of Mines developed a total flammable gas detector (TFGD) to measure CH, at concentrations up to 100% and to measure flammable gases in low 0, concentrations. This paper describes the operation and construction of the TFGD and discusses measurements of flammable mine gases obtained from a mine in western Pennsylvania.

Jan 1, 1992

By A. W. Deurbrouck, W. W. Agey

Introduction The modern wet concentrating table is a rectangular or rhomboid shaped normally rimed-deck operated in essentially a horizontal plane (Fig. 23). A drive mechanism imparts a differential motion to the deck along its long axis while water flows by gravity along the short axis. Tables are currently employed for processing large tonnages of coal and lesser tonnages of barite, beach sands, chrome, glass sand, garnet, iron, manganese, mica, phosphate, potash, tantalum, tin, tita-

Jan 1, 1985

By Chris Mark

In the wake of the Crandall Canyon mine disaster, the U.S. Congress asked the National Institute for Occupational Health and Safety (NIOSH) to study the safety of deep cover pillar recovery operations in the US. The legislation defined ?deep cover? to be greater than 1,500 ft, but NIOSH is also evaluating mines at depths greater than 1,000 ft when multiple seam interactions are encountered. By these definitions, there about 35 active mines that engage in deep cover pillar recovery, in the states of UT, CO, VA, WV, and KY. To date, NIOSH has documented ground conditions and ground control experience at nearly all of them. This paper provides an overview of current deep cover pillar recovery practice. Specific ground control issues that are discussed include: Pillar and barrier pillar design, ? Coal bumps, Thick seam pillar extraction, and ? Multiple seam interactions.? INTRODUCTI

Jan 1, 2009

By Louis W. Cope

INTRODUCTION Various methods for sampling placer deposits have been mentioned by Wojcik in Chapter 2. Here, a brief description and comparison of these methods will be given as related to bulk versus drill sampling. The advantages and disadvantages inherent to each will also be given. The means of sampling can be grouped into bulk or drill samples. As a generality, drill samples over a five-foot length will run from I/,, to 1 /, cubic yard, depending on the diameter of the drive shoe on the drill casing. Bulk samples can be expected to be in the range from one to many cubic yards each. SAMPLE METHODS Bulk Bulldozer-dug trenches and dozer or front-end loader pits are two methods to excavate large bulk samples. Smaller bulk samples can be obtained by digging small dimension shafts through the deposit, by hand or caisson-like drills. It is not recommended to split samples by alternate bucket-loads or by other means, as the effect of a nugget falling into one or the other fraction will seriously alter the sample.

Jan 1, 1992

By B. Amadei, A. Squassabia

This paper introduces the Rock Mass Median (RMM) index, a statistical measure of the mechanical quality of a rock mass thus is obtained through a mechanistic interpretation of the Poisson stochastic process. This process is the theoretical foundation of the Exponential Model, a probability distribution successfully used in practice to describe the spacing of discontinuities in rocks. Building on the Exponential Model, a simple method to compute RMM based on a widely accepted mechanical quality index is also presented. Verification is per formed through the analysis of two sets of core samples. Hypothesis testing at the 5% level of significance supports the validity of RMM for these samples.

Jan 1, 1994

By E. Topuz, M. J. McPherson, I. M. Konduri

Theoretical investigations and laboratory experiments demonstrated that there is a great potential for the use of jet fan ventilation in mines. This paper summarizes research that consisted of laboratory-scale model tests, full-scale mine model tests and underground coal mine entry tests. The laboratory model used water as a fluid medium and simulated a typical 25-m- (82-ft-) long heading having a 1.5 x 6-m (4.9 x 19.7 ft) cross section. The effects of various nozzle positions and designs were investigated by using still photography. It was also found that the use of jets in combination with line curtains enhanced the overall ventilating effect in the model entry. Flow measurements in the full-scale mine model and in the coal mine entry were conducted to evaluate the effectiveness of the jet fan. It was concluded that the designed jet fan ventilation system was an effective means of ventilating blind airways.

Jan 1, 1998

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990's. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990's for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By Thomas P. Meloy

A brittle solid broken by crushing or impact, results in a mass size distribution curve having a straight line segment when plotted on log-log paper. Depending on the mineral, the slope of this straight line segment ranges from a maximum of one for materials like glass and quartz to values of one half or less. Theoretical derivations of the size distribution, such as the Gaudin-Meloy model, yield a slope of one and only one. When the Gaudin-Meloy model is modified to assume that not all cracks terminate on a preexisting surface, the new model predicts that size distribution slopes, depending on the type of brittle solid, will be less than one. There is a measurable physical parameter that will predict the slope. In addition the model predicts that particles from such a size distributions will have negative corners and peaks - indentations. Moreover the model predicts that particle shape will systematically change with decreasing particle size. Finally, this new physical model of comminution may be experimentally tested.

Jan 1, 1995

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By Wojciech Suwala

The transition from centrally planned to market economy affects methods of economic analysis. The models which were used in the past are riot valid presently, however they we're the seed which initialized the development of methods and applications. There is more than twenty years of experience in modeling of coal mining development. The first attempts were devoted to select the moment of mine construction commencement in order to meet planned output. In Poland significant development of such models began in 1986. Within the Central Research and Development Program there has been a continuous development of models. These models from econometric to optimization ones, were a certain sequence which, in accordance with changing economy system, led to the last version of the model. It is the most suitable one for contemporary problems of coal mining in present Polish circumstances.

Jan 1, 1992

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985