Search Documents

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By R. Hogg

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most closer met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80 percent of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50 percent of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1971

By R. Brändle, R. Luis-Fonseca, R. Cornejo, G. Fischer, G. Von Rickenbach, J. Jarufe

Rock damage around underground excavations has been an important hazard in mines and tunnels. Rock dilation generates buckling that needs to be contained before it causes damage to equipment or safety concerns to mine workers. In seismically active mines, rockburst occurrence has been widely recognized as one of the most important hazards in deep mines and tunnels. While there is a wide range of cases where rockburst hazard can be mitigated through dedicated excavation sequences, reentry procedures or exclusion zones, there are still many situations where large unexpected rockbursting may occur, relying only on rock support as the last mitigation measure to prevent production and safety losses. Considering the previous situations, surface support as mesh, plays a major role containing the failed/ejected rock and providing a safe working environment to the underground operations. While there have been considerable achievements in improving mesh resistance, with more than 26Kj/m2 of energy dissipation capacity, there is still a lack of research in the overlapping mechanism and load transfer between contiguous mesh elements. This paper presents the state of the art in static and dynamic analysis of welded and rolled mesh overlaps, based on experimentation carried on by Geobrugg in their Research Center, leaving clearly established that the difference in meshes is not only in levels of energy absorption, but also concluding that in the case of high resistance rolled meshes overlapping is not necessary and the transmission of stresses can be fully guaranteed by using suitable connecting elements. All these characteristics, supported by operational advantages as light weight and mechanized mesh installation, provides a considerable improvement in safety and productivity, improving the economic value of the project

Apr 26, 2022

By C. Flores

It is well known that manganiferous silver ores containing manganese intimately associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily for recovering copper from oxidized and oxide-sulfide ores. A new alternative process combining segregation roasting followed by flotation to recover silver from refractory manganiferous silver ores, was studied using a 23 factorial experimental design. Laboratory investigations have been conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/ton silver to study the effects of additives salt, coke and copper oxide on silver recovery. Results indicate that 79.3% silver recovery can be attained in the absence of copper oxide and 88.4% when the copper oxide content is 1.5% at &apos;750°C, 2% salt and 1% coke and 30 minutes of roasting time. It was concluded that doping with copper oxide improves silver recovery.

Jan 1, 1994

By E. A. Barrett, L. L. Rethi

Throughout all segments of the United States mining industry, 163 independent contractor employees were fatally injured between 1990 and 1997. Factors that contributed to these injuries were identified after reviewing descriptive information contained in Mine Safety and Health Administration fatality reports for each of the incidents. Thirty-three unique contributing factors were identified and multiple factors were noted for each fatality. Those most frequently discerned were "failure to follow `standard operating procedures"&apos;, (35% of the fatalities), "poor positioning of employee" (26% of the fatalities) and "failure to maintain equipment" (23% of the fatalities). Contributing factors were then associated with the accident and job classifications of the victims. Factors having the highest frequencies in the top five accident classifications where most fatalities occurred were as follows: powered haulage - "failure to maintain equipment"; machinery - "poor positioning of employee"; slip/fall of person - "inadequate fall protection" and "failure to wear safety line"; electrical - "equipment contact with power line"; and falling/rolling/sliding rock - "poor positioning of employee. " Among the job classifications in which most fatalities occurred, leading contributing factors were as follows: truck driver - "failure to follow standard operating procedures" and "poor positioning of employee"; laborer/utility man/pumper - "poor positioning of employee"; mechanic/ repairman and welder - "failure to follow standard operating procedures." Recommendations for utilizing contributing factor information as a basis for safety training are proposed. Training programs may be developed that inform independent contractor employees of factors which, in the past, have contributed to fatal injuries in their job classifications. Then, by combining this information with contributing factors identified in "related" accident classifications, a truly focused training intervention that addresses very specific workplace hazards may he developed.

Jan 1, 2002

By Jose F. T. Agapito

The mining engineer must be able to predict the structural behavior of the rock around underground openings so that he can answer questions relating to safety and economics. With the present status of rock mechanics knowledge, exact predictions cannot be attained and approximate idealizations are made. As a first approximation, structural design makes use of theory, laboratory testing of rock properties, and available experience from excavations in similar rock formations. However, realistic design can usually be obtained only after in-situ observations and measurements are made. After all the information is collected, judgement and experience play a most important role in the final formulation of the design. This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator, The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale, The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver (Figure 1) . Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River Formation at a depth of 600 to 850 ft, Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek, The distance from the mine to the side of the mountain varies from 500 to 1,200 ft, and its height above the stream floor is approximately 700 ft.

Jan 1, 1974

By H. J. Hutson

BRS, Inc. has utilized Carlson&apos;s Natural RegradeTM software to design the reclamation and stabilization of abandoned open pit uranium mine spoils, AML Project 16N, located in the Gas Hills Uranium District in central Wyoming. This work was completed for the State of Wyoming&apos;s Abandoned Mine Land Program (AML) on preSMCRA (Surface Mining Reclamation and Control Act) sites for which no reclamation obligation existed. The project successfully stabilized an eroding spoil dump, enhanced the local view shed, created habitat diversity and provided a significant source of fill material for open pit highwall hazard mitigation efforts. Additionally, the project served to evaluate innovative reclamation design methods, engineering software and grade control technology. This project was nominated for a National Association of Abandoned Mine Land Programs award by the State of Wyoming. The results of this project will be presented as a case history of the Natural RegradeTM approach to surface mine reclamation. Based on the successful application of this new mine reclamation technology on the AML 16N Project, reclamation designs for spoils associated with planned underground uranium mine operations at the Velvet Mine in the Lisbon Valley Uranium District of Utah for Uranium One USA, Inc have been prepared and will be presented. Critical elements will be the encapsulation of unsuitable materials, long term hydrologic stability, and sequencing and staging of ore and mine waste for final reclamation surface construction. The goal of the Uranium One Velvet Project will be to apply best available technology to reclamation planning and fully integrate the reclamation design with the mine planning. Benefits of the approach should include improved public and regulatory perception of the project, facilitate mine permit approvals and the eventual timely release of reclamation bonds, as it is anticipated the stable landform created through this process will result in more rapid stabilization of the site to pre-mine geomorphic conditions. NATURAL REGRADETM CASE STUDY AML Project 16N, D-9 and K Pit Reclamation Project, is located in an intensely disturbed area of the West Gas Hills Uranium Mining District in Fremont County, Wyoming. The overall design calls for the placement of approximately 7 million cubic yards of backfill materials in the D9 and K Pits, imported from adjacent mine spoils including the Central Spoils, and from local highwall excavation. Figure 1 shows the location of the Central Spoils excavation area, as well as the D9 and K Pits fill area. The entire project is located on public lands administered by the Bureau of Land Management, Lander, Wyoming District Office. No access controls are in place at the abandoned mine sites. The public lands are administered under a multiple use land policy including grazing of range land, public recreation, active mining and exploration, and oil and gas. The project site is located along Fremont County Road No. 5, which is a moderately well traveled road. Reclamation of the numerous and large abandoned open pits in the Gas Hills Uranium District has reduced the risk of death or injury to the public. Site History and Background The Gas Hills Uranium District was mined by multiple companies during the period from 1955 to 1981. The uranium was hosted in the Wind River formation, a sequence of soft sedimentary layers of interbedded sandstone, clayey shales, and conglomerates. Uranium was precipitated out of ground water in classic roll front deposits, which are found from very near surface to depths greater than 400 feet. Prior to the enactment of the Surface Mining Control and Reclamation Act of 1977 (SMCRA), very little reclamation work was performed when mines were abandoned or closed. The State of Wyoming Abandoned Mine Lands Program has worked to mitigate hazards associated with large open pits, control migration of unsuitable materials and restore watershed functionality of lands in the district. Additional reclamation is being performed by mining companies on bonded lands. Figure 2, Gas Hills Uranium District aerial photograph, shows the extent of the mining disturbance in the district. [ ] Project Hazards and Concerns The purpose of AML Project 16N is to mitigate hazardous conditions and risk to the public associated with open pit highwalls and toxic, acid forming, and /or radioactive mine waste materials. The D9 and K Pits are contiguous open pits characterized by an 8,800 foot long hazardous highwall that averages over 200 feet tall. In addition to the physical hazard presented by the highwall, the project addresses

Jan 1, 2009

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By R. R. Klimpel

This paper describes four new families of flotation products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1992

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By G. Ofori-Sarpong, A. -S. Adam, R. K. Amankwah

"In the application of the BIOX® technology, high tailings grade (2-16 g/t) may be generated with a decrease in overall gold recovery, which sometimes make it economically unattractive. This paper investigated the causes of the high tailings grade by using samples from the Bogoso BIOX plant. Partial chemical analysis, diagnostic tests and cyanidation optimisation studies were conducted to invoke understanding into the high tailings grades. Diagnostic study on the tailings showed 48.34% of gold in carbonaceous matter, 17.12% in quartz, 13.40% as liberated gold, 11.51% imbedded in sulphides and the remaining 9.65% in carbonates. Optimum cyanidation recovery of 90.4% was established for the BIOX concentrate at 7 kg/t NaCN, 40-50 g/L activated carbon and residence time of 40 hours. The recovery was sensitive to carbon and cyanide concentrations but additional cyanide was not economical. High preg-robbing indices of 72.7% and 64.4% were recorded for the BIOX product and the flotation concentrate respectively. This confirms the inability of the BIOX process to deactivate carbonaceous matter, which remains a serious precursor for low overall gold recoveries and high CIL tailings. INTRODUCTION Gold ores may be broadly classified as refractory and non-refractory. Non-refractory ores are easy to treat but refractory materials require complicated flowsheets for metal extraction (Hausen and Bucknam, 1985; Schmitz et al, 2001; Marsden and House, 2006). As near surface non-refractory gold deposits are getting depleted, the increasing price of gold and increasing demand for gold, have encouraged many gold producing companies to treat refractory ores for gold recovery. The refractory behaviour of these ores may be due to the presence of sulphides, tellurides, cyanicides and/or carbonaceous matter. Refractory ores do not respond well to conventional cyanidation as the gold is either occluded by or in solid solution in sulphides, or is in association with cyanicides (Marsden and House, 2006). Further, carbonaceous matter preg-robs gold during leaching (Osseo-Asare et al, 1984; Hausen and Bucknam, 1985; Schmitz et al, 2001). The two major causes of refractoriness are the presence of sulphides and carbonaceous matter, and these render the ore double refractory (Nyavor and Egiebor, 1992). Oxidative pre-treatment processes such as high pressure leaching/oxidation; biological oxidation, ultra-fine grinding and roasting are required to render refractory ores amenable to conventional cyanidation (Marsden and House, 2006). Biological oxidation, however, has become the preferred pre-treatment route because it is more environmentally friendly and convenient even where only partial oxidation is required. Comparative tests have demonstrated that bioleaching can achieve the same or better results than roasting or pressure leaching in terms of gold recovery (Yannopoulos, 1991; Brierley, 1997). Further, biological treatment processes are more cost-effective, environmentally friendly and safer."

Jan 1, 2017

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By John Murray, Daniel Ebin, Robert Gould, Yiming Sun, Lizan Gilbert

The Atlanta Plane Train Tunnel West Extension is being constructed at Hartsfield-Jackson Atlanta International Airport using the Sequential Excavation Method (SEM). The tunnel has shallow ground cover and mixed-face conditions and passes underneath the SkyTrain and MARTA stations and airport terminal buildings. It includes a twin tube Bifurcation with a span of over 45 feet and ground cover of 12 feet. A flat roof is being constructed at the Bifurcation to maximize rock cover and minimize surface settlements. This paper focuses on design and construction challenges for the Bifurcation and tunneling beneath the world’s busiest airport, while minimizing impacts to operations.

Dec 1, 2022

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By R. Benemelis

The existence of resins in some coal deposits in various parts of the world has been known for many years. These resins vary considerably in chemical structure and properties. The resin that is found in Utah coal, however, is rather unique, and has properties particularly attractive for the manufacture of printing ink mastics and adhesives. This resin is a rather dark, very high melting point, low molecular weight hydrocarbon resin. Its typical properties are shown in Table I. Its largest use by far, has been in the printing ink industry. The history of Utah coal resin is interesting, but unfortunately one of disappointment and failure.

Jan 1, 1990