Search Documents

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By A. D. Hammond

Vanadium is a transition metal, ductile, silver-gray metal. It is harder than most metals and steels and it has a good resistance to corrosion, it is stable against alkalis, sulfuric and hydrochloric acids. Vanadium is oxidized in air about 660 °C, although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states 2-5. In aqueous solution the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called, roscoelite K(V3+,Al,Mg)[(Si,Al)4O10](OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world's vanadium mine production comes from magnetite-hosted deposit and to a lesser extent, in sedimentary-hosted sandstone. Vanadium is also present in bauxite and in fossil fuel deposits such as crude oil, coal, oil shale and tar sands. In crude oil, concentrations up to 1,200 ppm have been reported. A significant vanadium production comes from the processing of petroleum residues, fly ash and recycling spent catalysts. In 2011, metallurgical applications accounted for 93% of the use of vanadium. Here, an alloy called ferrovanadium is utilized to strengthen steel to be used as rebar in the construction industry, in the manufacturing of axles, crankshafts, gears and chassis in the automotive and transportation industries and in the manufacturing of high-speed tools. In the aerospace industry, vanadium is utilized as a titanium alloy in the manufacturing of airframes and jet engines. The reason for the wide use of vanadium as alloy is its high strength-to-weight ratio, the highest of any engineered material on earth. The major non-metallurgical use of vanadium is in the production of catalysts for the chemical industry. The most commercially important compound is vanadium pentoxide (V2O5), which is used as catalyst in the production of sulfuric acid.

Feb 23, 2014

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014

By A. L. Hornbaker

Colorado has recorded more than 100 years of industrial mineral production. Much of the state's history, culture, and economy is based in mining, but the industrial minerals and construction materials comprising the nonmetallics sector of the industry very often are overlooked or overshadowed by mineral fuels and the metals. Indeed, many of these materials find use in seemingly unimportant industrial applications essential to our economy and life style and yet are not so recognized by the consumer. Unlike many other mineral resources, the numerous industrial minerals occur in many different and often exotic geologic environments, some of which are characteristic only of the western states. In Colorado only a few of these minerals have continued production through the years; many saw only "boom" periods or other critical times of need, such as the world wars. The changing needs and demands of our society in the 1980s will stimulate yet another era of intensive activity in our industrial minerals storehouse. Researchers are finding new uses and applications for these materials in dealing with the energy crisis and fuel shortages, the need to develop domestic mineral reserves of all kinds, and the goals of reuse and recycling. Some of Colorado's little-used and unused industrial minerals hold extraordinary promise in solving some of these problems on the regional and national levels. In this paper we will look at the history of development of Colorado's more prominent nonmetallics and especially at current research on and future potential of several other commodities among which Colorado contains the largest known reserves.

Jan 1, 1980

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By W. D. Macleod

This paper describes a mineral dressing process for the upgrading of tin ores. The process described is called 'agglomeration' and. is similar in many respects to flotation. Many variables have been examined experimentally both on batch and continuous operations and are reported upon herein... Using a Mt. Pleasant tin ore, assaying 0.5% Sn, an upgrading to 8% Sn, with a recovery of 95% could be obtained by this process.

Jan 1, 1966

By Herbert F. Nyberg

The Black River Falls Mine is owned and operated by Jackson County Iron Company, a wholly owned subsidiary of Inland Steel Company. It is located in vest central Wisconsin, seven miles east of the city of Black River Falls. This is the first taconite plant in the state of Wisconsin. Iron mining started in this area in 1856 but soon failed due to the low grade ore and crude methods of mining and transportation. Inland Steel Company acquired the property in 1939. Some drilling and test work was done in 1940, but the economics of developing the property at that time were not favolable. Improved methods of concentrating and pelletizing in the 1960's made it possible to build the present plant. Due to the limited ore reserve of 45,000,000 tons with expected recovery of 33% it was necessary to limit the capacity of the operation to 750,000 TPY with a life of 20 years. There was some concern about an operation of such limited capacity. A million ton operation was considered the minimum size plant for a profitable operation.

Jan 1, 1976

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By Chris Lynagh, Collin Schroeder

Determining the best excavation method is a critical step in successful tunnel construction. In rock tunneling, several factors can dictate the excavation method, such as: (1) rock characteristics, (2) tunnel size and length, (3) nearby utilities/infrastructure, and (4) contractor’s preferred means and methods. This paper discusses the various rock tunnel excavation methods utilized on the Doan Valley Storage Tunnel Project (DVT), a project constructed as part of the broader Project Clean Lake in Cleveland, Ohio. The differences between each method’s initial and final lining, geology, and cycle sequence will be analyzed and compared.

Jun 13, 2023

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

By B. G. White

Traditional interpretations of vein ore deposits in the Coeur d' Alene Mining District, such as the view that these deposits formed in a transcurrent tectonic regime during the Precambrian, are being supplanted by the view that the deposits (1) formed in low-grade metamorphic shear zones similar to those that host an important type of gold deposit, (2) display features, such as wall rock carbonate zoning and vein zoning, that are common to ore deposits elsewhere, and (3) are probably Mesozoic and possibly related to emplacement of the Idaho batholith. In recent years, new interpretations have led to major ore discoveries that are likely to extend the life of the district for decades.

Jan 1, 1998