Search Documents

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By V. Rajaram

The Metropolitan Water Reclamation District of Greater Chicago (MWRD) imposed a no-blasting specification (blasting is restricted to the construction shaft and shaft bottom or boot) on the Deep Tunnel project in 1988. This was prompted by numerous complaints from the residents in the vicinity of the project, and controversies experienced on previous projects from blasting the rock overlying the tunnel. This paper will describe the methods utilized by two major contractors who are driving 20 km (12.5 of tunnel along with drilling over 36 shafts under this restrictive specification. The impacts on design, construction, schedule, cost, and the environment are detailed.

Jan 1, 1991

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

By K. E. Harrison

The acid rain legislation has passed into law. This new law has caused the power generation community to investigate alternative methods to obtain compliance with the new legislation. One thing all of the power companies have concluded is the answer is not easy. Do we switch fuels to burn all low sulfur compliance coal? Maybe possibly only partial desulfurization by means of a dry sorbent system? Or, finally, maybe a wet scrubber system? Whatever the choice, the power community needs to investigate all of the alternatives. In 1988, ICF Kaiser Engineers, Inc. (ICF KE) responded to a request by the U.S. Department of Energy for the engineering development of advanced physical fine coal cleaning. ICF KE responded and was awarded a contract to conduct a multi-task program to develop an advanced flotation system to eliminate pyritic sulfur and retain as much energy as possible. ICF KE assembled a team that included members of industry, academia, and industry research organizations to conduct this multi-task program. The program includes sixteen (16) tasks. This team had personnel to help solve some of the anticipated problems and to provide industry prospective on the viability and commercial potential for any concepts proposed. The primary team consists of a major coal producer, Babcock and Wilcox, Eimco Process Equipment Company, and Virginia Polytechnic Institute and State University.

Jan 1, 1992

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

3.1 INTRODUCTION The final subsidence basin discussed so far is that developed long after mining has stopped. In a supercritical final subsidence basin, the central portion subsides uniformly. Thus any structures located there are not subjected to any final permanent surface deformation. But this statement is only true for the final subsidence basin. When the face is moving, the structures are subjected to dynamic deformations associated with the dynamic subsidence basin. For instance the house in front of a moving face (location 1 in Fig. 3.1) is subjected to the maximum tensile strain and the maximum positive curvahue. When it falls behind the face in location 2, it is subjected to the maximum compressive strain and the maximum negative curvature. When the house is far behind the face in location 3, it returns to its original condition with only uniform subsidence. However, the magnitude of the dynamic deformations may be sufficiently large to damage a structure in locations 1 and 2 before it reaches location 3. Therefore it is very important to study the characteristics of the dynamic subsidence basin. Under normal conditions, when the face has advanced for a distance approximately one-sixth to one-third of the seam depth from the setup entry, depending on the seam depth and the physical properties of the overburden strata, the movement of the over- burden strata reaches the surface, whereupon the surface also be- gins to deform. Thereafter, the surface point where the movement initiates is always located at a fixed distance ahead of the face. The angle between the vertical line at the faceline and the line connecting the movement initiation point on the surface and the face- line is the angle of advance influence, w. The angle of advance influence can be used to determine the distance, [ 1], which is the influence zone ahead of the face. w is approximately 20O to 35 O for the northern Appalachian coalfield (Peng and Geng, 1984). The movement of each surface point is a relatively complicated process both in time and in space, because the relative position between the faceline and each surface point varies continuously, so that the direction and rate of movement for each surface point differ. In the following sections, the movements of each surface point on the major cross section are illustrated. 3.2 DYNAMIC SURFACE MOVEMENTS Dynamic surface movements include dynamic subsidence and displacement. The movement of each point on the subsidence basin is different as the face advances from 1 to 6 (Fig. 3.2). Surface points A and B, being far in front of the moving face, subside and displace toward the face (i.e., from A to A' and from B to B'). Point C, which is quite near but in front of the moving face, subsides continuously but displaces initially toward the face and then turns to pure subsidence ending up at C'. Point D, which is behind the face above the gob, subsides continuously, but displaces initially toward the face when it is in front of the face and reverses to follow the moving face when it is behind the face, with the amount of displacement toward the face being larger than that following the face. As a result the net displacement is toward the center of the gob (i.e., from point D to D'). The same statement is true for point E. For point F, the net displacement is zero, i.e it appears to have dropped down vertically to F'. For points G to I, the net displacements are in the direction of face advance except the magnitudes are increasing in sequential order. Point 1, has reached the final dynamic position of 1'. In other words, the face has passed sufficiently away such that it does not affect the movement at point I. All other points (A to H) are still within the face influenced area. 3.3 DEVELOPMENT OF DYNAMIC SUBSIDENCE PROFILES When the face has moved for a distance of h/6-h/3 from the setup entry, surface subsidence reaches the surface. At this time the surface subsidence basin is very mild (S, in Fig. 3.3), and it is symmetrical about the center. As the face continues to advance, the maximum subsidence continues to increase, and its location moves with, but falls farther behind the face. When the face has advanced a sufficient distance, e.g., (0.9-2.2)h, away from the setup entry, the maximum subsidence reaches the maximum possible value (curve S,). At this time, the dynamic subsidence profile is fully developed. Thereafter both sides of the dynamic subsidence profile become stabilized. The subsidence profile on the face side moves with the advancing face in an orderly manner (curves S, and S,). When the face stops, the face side of the profile continues to subside and becomes stabilized (curves;) sometime after. Curve S; is the final subsidence profile (see Fig. 2.22). 3.4 DEVELOPMENT OF DYNAMIC DISPLACEMENT AND SLOPE PROFILES The dynamic displacement profile moves with the advancing face (Fig. 3.4), but changes according to some specific rules. When the face has advanced to A, the surface begins to move and its dynamic displacement profile has two maximum values (curve Ua): one positive near the setup entry moving toward the face advancing direction and the other negative on the face side also moving toward the face advancing direction. As the face continues to advance, the positive maximum displacement on the setup entry side increases and moves toward the face continuously. The same statement is true for the negative maximum displacement on the face side. When the opening increases to the critical size, both the maximum positive and negative displacements reach the peak values and remain constant thereafter. Notice that when the opening becomes critical in size, the point of zero displacement no longer moves with the advancing face. Rather it spreads into an area of zero displacement (curve Ue) and expands as the face advances. When the face stops, the displacement on the face side continues until it becomes stabilized (curve Úe). Curve Úe is the final displacement profile. The ratio of maximum dynamic to final displacement ranges from 60 to 75%. The dynamic slope profile follows the same patterns of change. The ratio of maximum dynamic to maximum final slope ranges from 50 to 80%. The maximum slope decreases with in- creasing rate of face advance (Peng and Geng, 1984). It must be pointed out that except for those near both sides of the profiles, each point on the displacement and slope profiles is subjected to a cycle of positive and negative displacements and slopes depending on its relative position with respect to the face.

Jan 1, 1992

By Donald R. Williamson

The Cyprus Pima Mining Company's open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. At that tine reserves were law - volume (+10 million tons) and high grade (+1.5% Cu). Several periods of growth have brought the operation to its present production level of 55,000 tons per day of ore and +125,000 tons of waste. Over the years, a number of attempts to refine and polish the ore reserve figures have been made using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Other refinements were tried using adaptations of established methods combined with computer modeling techniques. The resulting mine-model ore blocks were an improvement but they still tended to show too match tonnage of mill feed, often at too low a grade. One attempt at Kriging had only limited success. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons thus far between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results. A new, better procedure for estimation of ore reserves apparently has been developed for the Cyprus Pima deposits. The specific procedures seem likely to have direct application to other, similar operations. The methods used to develop the procedures could be of value to still other operations.

Jan 1, 1976

By Neely H. Bostick

The primary and secondary organic matter in sedimentary rocks changes markedly when it becomes heated as a consequence of thick sediment accumulation and normal geothermal gradients, high geothermal gradients, hydrothermal fluids, or igneous events. Contact zones adjacent to small igneous dikes allow sampling of a single sedimentary bed that has been exposed to temperatures in a range as great as 30-500°C. Dike-heated rocks are, therefore, good sites for research on thermal effects because variation of the original organic matter is minimal, the range of heating is great, and the history of rock heating in a dike zone is relatively well established. In rare cases, such as at the dike near Wolcott, Colorado, described in this paper, the rock samples are sufficiently unweathered to allow analysis of secondary bitumens generated by the heating. We show by optical microscopy, scanning and transmission electron microscopy, and geochemistry the kinds of solid organic constituents in sedimen¬tary rocks and in ore deposits and the effects of heating. The primary phytoclasts that make up kerogen In sedimentary rock and in some ore deposits (pollen, resin, charcoal, humified woody remains, etc.) change in ways that are familiar to coal specialists. Progressive loss of moisture and other volatile matter yields residual kerogen that Is relatively higher in carbon and lower In oxygen and hydrogen, and has greater molecular or polymer ordering. In our contact zone examples, atomic H/C ratios of kerogen decrease from 0.8 (one case from 1.4) to 0.4, the hydrogen index from Rock-Eval pyrolysis decreases from 70 to 5, and the transformation ratio from Rock-Eval pyrolysis increases from 0.06 to 0.5 with increased heating. The visible effects of heating seen by scanning electron microscopy and light microscopy include formation of vesicles and flow structure, the development of optical anisotropy and mesophase, change of color, and increase in the refractive index, absorption, and reflectance. Some of these changes In primary organic matter are observed also in secondary organic matter, for example, in solid bitumens in sedimentary gold ores or In lead-zinc deposits. Quantification of color or absorption changes is difficult because it Is hard to make thin sections of organic matter with uniform thickness. However, natural objects with uniform thickness can be used. We show the colors of pollen In rocks from the Salton geothermal field at temperatures ranging from 100 to 300°C, and of pollen heated in laboratory bombs from 150 to 400°C. Measurement of vitrinite reflectance is a practical way to quantify thermal changes of kerogen and minerals of most sedimentary rocks because vitrinite is fairly widespread In sedimentary rocks of Devonian age and younger. For example, the reflectance of vitrinite rises from the regional level, as low as 0.4 % Ro, to more than 5% Ro adjacent to dikes that cut sedimentary rock. This is equivalent to the rank change from subbituminous coal to extreme meta-anthracite. The rise is most abrupt near thin dikes, but when the distance from the igneous contact is expressed as a ratio of dike thickness the reflectance rise is similar for all dikes. Controlled heating of vitrinite-bearing rocks In the laboratory provides a means to assign known temperatures to vitrinite-reflectance values. The derived plots of temperature In dike contact zones have the same shape and level as those predicted by heat theory, and the temperature lines extend toward dike contact temperatures that are about half those of most magmas, as expected if the intrusions did not flow past the sedimentary rock for a long time. The globular submicroscopic structure of vitrinite and Its heterogeneity, which we show by means of transmission electron microscopy, pose some problems In selecting a uniform type of vitrinite for measurement of thermal changes. At present, routine reflectance values of vitrinite dispersed in rocks have a relative uncertainty as great as 10%. Thermally caused chemical changes in the primary kerogen, especially decrease in the oxygen and hydrogen contents, lead to formation of secondary products in the contact zone. The measured changes of secondary organic products in these rocks include formation of peaks In concentration of total extractable organic matter and in hydrocarbons, and in the saturated/aromatic hydrocarbon ratio over the interval where primary organic hydrogen decreases most rapidly--then destruction or expulsion of these products at high temperatures. The odd carbon-number predominance of the C25-C31 n-alkanes In samples far from the dike disappears by about 1.3% Ro whereas the 13C: 12C ratios of the saturated and aromatic hydrocarbons increase over most of the thermal range. The saturated aromatic hydrocarbon ratio at first increases, corresponding to thermal generation of saturated hydrocarbons, then decreases in the most altered samples. One use of organic petrography, in addition to identifying organic fades or thermal alteration, is recognition of sample contamination such as the solid organic additives used in some drilling muds which may contaminate geochemical samples.

Jan 1, 2013

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984

By P. Somasundaran

Three major types of solution chemical equilibria involving flotagents (Le. flotation reagents such as collectors, frothers and modifiers), minerals and solution play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various flotagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1990

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Eric Sitorus, Septian Prahastudhi, Roy William, Wieda Azani

In July 2020, massive slope failure occurred in the southeast corner Grasberg open pit. This was the final episode in the breakthrough of Production Block 2 South (PB2S) of the Grasberg Block Cave to connect to the surface. This breakthrough had been rapidly evolving during the first half of 2020 and occurred as expected with no adverse impacts to safety or operations. To manage and safeguard the exposure to the workforce and operations, numerous hazards were identified and anticipated. The failure of the sill pillar between the open pit and PB2S cave was identified as the main area of interest and was closely watched during the failure process. This paper reviews the systematic approach developed to convert monitoring data into information around the collapse of the GBC PB2S cave sill pillar. The data that was interpreted consisted of micro-seismic, piezometric, ground-based radar and observational inspections. Geological structures on the boundary of the PB2S cave were clearly involved in the breakthrough process. As the cave propagation reached these structures and triggered instability, the resulting acceleration and breakdown were clearly shown by IBIS radar units associated with high movement in the slope. The focus of this paper is on the evolution of changes seen in the micro-seismic data and how it was used to understand the rapidly changing conditions of the sill pillar. The seismic parameters evaluated were event distribution, Es/Ep value, and the seismic moment tensor inversion. The changes of breakthrough indication seen in these parameters were substantiated by Shear Wave Splitting (SWS) analysis that showed a close correlation with the fractured zone above the PB2S cave as indicated by the increasing anisotropy.

Jan 1, 2022

By James E. Lawver

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve platting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plats are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples. An overview of the flow charting of the system is provided in the addendum.

Jan 1, 1978

By H. M. Ray

The discovery of the New Lead Belt in the mid-'50s began a search for mill design criteria that is continuously updated. The opportunity to design, construct, and operate four new mills in the span of 20 years provided fertile areas for new concepts. The central theme for design parameters encompassed simplicity, functional, and economic consideration. Ore characteristics for each plant remained relatively constant, providing stable criteria for grinding circuits. Bond index nominally 10-12. Flotation circuit parameters were based upon power application with 10-20% excess capacity built-in to protect recovery. Newer equipment exhibits greater power application efficiency lowering horsepower requirements per ton. Instrumentation was installed to stabilize circuits, protect equipment, and improve products. With ever increasing requirements of higher quality products, environmental considerations, and operating cost pressures, the upgrading of operating procedures is in a constant state of flux. Installation of more efficient equipment, chemical processing, or any other technique would be considered as feasible. Current practice is for St. Joe to design and engineer in-house its own plant design. The exception being detailing of structural steel. It is felt that familiarity with past design criteria serves as a valuable foundation to incorporate changes. Also, direct contact with operator provides specific data, and feedback for constructive criticism that is utilized for defining and correcting problems. The results are in reality an operator's plant with the benefit of advancing technology that meets the demands for improved products without sacrificing the economies of throughput or recovery.

Jan 1, 1977

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014