Search Documents

By S. P. Singh

In order to simulate the operation of coal extraction machines, a portable workability instrument has been designed. Initially, the tests were performed with the instrument on modeling material, which were followed by in situ tests on coal in underground mines. The peak and mean cutting resistance and work done to cut a unit length of coal were determined for coal as well as modeling material. In addition, rebound strength and dynamic penetration tests were also performed in situ. On the basis of the cutting characteristics of coal, a "Workability Index" has been developed and its role in the judicious selection of coal cutting machines has been discussed. With reference to prior works and the strength characteristics of coal, it was found that the coal plow may not be suitable for the seams under investigation and the shearer seems to be the only choice. It has been observed that peak cutting resistance and the "Workability Index" in the case of coal as well as modeling material depend upon compressive strength. The peak cutting resistance exhibited certain dependence upon the Schmidt rebound hardness and dynamic penetration strength of coal in situ.

Jan 1, 1984

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By John G. Holmes

The generation of low cost power is but one phase of the TVA program for regional development. During the 36 years since TVA began, growth in its generation of electric power has necessitated a shift from a predominantly hydroelectric power system to a combination steam and hydroelectric system. The addition of steam-electric power plants to TVA's generating system was necessitated by the rapid increase in the traditional and defense demands for electric power in the 80,000-square-mile area served by TVA, the need to firm up the hydroelectric power, and the fact that all available sites for sizeable hydroelectric projects had been developed. At present TVA owns and operates 40 power plants--29 hydroelectric and 11 steam-electric plants. The total generating capacity of the hydroelectric plants is 3,105,430 kw, and the capacity of the steam plants is 13,951,135 kw. This provides a total generating capacity of 17,056,565 kw for the plants operated by TVA. Individual capacity of the 112 hydroelectric units ranges from 10,000 to 67,500 kw, and the individual capacity of the steam-electric units now in operation ranges from 60,000 to 950,000 kw. In addition to this generating capacity, TVA distributes the power from 6 U. S. Army Corps of Engineers hydroelectric plants on the Cumberland River. These plants contribute an additional 725,000 kw. Also, under an agreement with the Aluminum Company of America, TVA directs the stream flows and generation of their 423,715-kw system on Tennessee River tributaries and shares with Alcoa in the increased generation resulting from this coordinated operation.

Jan 1, 1969

By K. F. Clark

Some 30 years ago Stevenson (1940) underscored the fact that most of the world's molybdenite production came from the Cordillera that comprise the western part of North America, and that the northern extension of the Cordillera into British Columbia is not essentially dissimilar to the United States section. Therefore, in view of the successful development of molybdenite resources in the United States, he concluded that prospecting in the Canadian section f the Cordillera should be encouraged. However, as recently as seven years ago Schneider (1963) remarks that no large economic deposits have been brought into production in British Columbia, although one important property was being evaluated. World production f molybdenum ore was sporadic until 1900. Among the very early producing areas in North America were Arizona and New Mexico in the United States. World War I provided the stimulus that brought the Climax deposit into production, and in 1920 Questa, New Mexico followed, although the ore came from fissure vein deposits at that time. In the early part f this century high grade deposits in various parts f the world containing 5-20 percent MoS2 were exploited. In Canada most production during World War I came from Quebec and Ontario. With the build-up of world tension and the inception f hostilities in 1939, British demand was satisfied by United States producers (Schneider, 1963).

Jan 1, 1970

Flotation of dolomite from apatite was investigated, using dodecylamine hydrochloride or sodium oleate as the collector, in the absence and presence of inorganic modifiers such as sodium chloride. Separation of dolomite from apatite was anticipated from the single mineral experiments under various pH and collector concentration conditions. Flotation selectivity in the mixtures, however, was found to be limited. Attempts to control the flotation response of these minerals by addition of salts such as NaCI and KCI indicated that selectivity is possible. The presence of sodium chloride was determined to depress apatite flotation using sodium oleate leaving dolomite flotation unaffected (Moudgil and Ince, 1989). In this paper, conditions for optimum separation and the effect of major parameters on the desired selectivity are discussed.

Jan 1, 1990

By R. R. Young

Good afternoon gentlemen. It is always a pleasure to talk about a subject dear to our hearts--the high speed transfer of bull; materials. Specifically, today we will be reviewing the engineering approach to an age old problem of ship loading and unloading. You may be puzzled by the title of this paper and we will attempt to explain this for you--particularly the use of the words "New Era", since high speed automated facilities are nothing new to the material handling engineer. The new era in material handling designs refers to an all out concerted effort to provide custom engineering tailored to specific operations and economic requirements of the client. It shuns hardware type of engineering wherein existing machines and devices are dusted off and reapplied. It provides automation when automation can be justified and it exemplifies the application of systems engineering to solve specific problems.

Jan 1, 1967

By John H. Bassarear

By 1968 Cyprus Pima was milling 38,000 tpd of copper ore using a conventional flowsheet consisting of three stages of crushing rod mills and ball mills. A 15,000 tpd expansion was put on stream late in 1971 using primary crushing, semiautogenous mills, and ball mills. Identical ore is treated in both concentrators. This paper shows the weight and life of each individual liner for each crusher and each mill over a four year period from 1974-1977. Power and media consumption are shown for the same period and a comparison is made between the two reduction methods.

Jan 1, 1980

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

By Robert Charles Alfred

Evolution is continuing in the field of rock drilling, Campbell Limestone Company is experimenting in the higher air pressure phase of drilling, It has been determined that there is a definite relationship between Air Pressure, Penetration Rate, Bit & Tool Wear and Life, In our drilling we have determined that &e higher air pressure gives a better penetration rate with less bit wear per foot. Drilling with 180 to 200 PSI air pressure, instead of 100 PSI for air and/or churn drills, has decreased our primary costs by approximately one half.

Jan 1, 1963

By S. C. Carniglia

Bayer-process alumina hydrate becomes in turn the source of a host of special products in addition to the calcines that feed aluminum reduction cells. Though relatively smaller in tonnage, specialty aluminas serve important industrial markets in an exciting and growing variety. Production methods and applications are discussed for: (1) trihydrate as flame retardant in organic materials; (2) high-surface-area transition aluminas as desiccants and scavengers, catalysts and substrates; (3) calcines for industrial ceramics, refractories, and abrasives; and (4) tabular alumina for refractories, bed supports and other uses.

Jan 1, 1977

By Norbert Steiner, Roy Norcross

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O2 instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O2 with SO2 yielding H2SO4 up to 70% strength, depending on off-gas tem­perature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentra­tion, residual SO2 concentrations of less than 20 mg!Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O2 process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By John J. Dran

Large mining companies use a number of sophisticated analytical techniques for introducing the element of risk into the valuation of mineral reserve sites. These methods include, but are not limited to, sensitivity analysis, computer simulation, conditional probability, and portfolio theory. Such techniques enable the managements of these large companies to have an awareness of the many possible ramifications of their investment decisions. On the other hand, small mining companies and individuals in the mining business, due to limited financial and technical resources, still rely primarily on single point estimates of the value of mineral reserves. These small miners introduce the aspect of risk only through the application of an appropriate "speculative" discount rate. This paper illustrates the application of a technique for the introduction of risk into investment analysis. The method appears to be most suitable for use by small mining companies and individuals contemplating a large investment in a new mineral reserve site.

Jan 1, 1974

By H. E. Rutherford

Monterey Coal Company has begun a geologic monitoring program in order to better understand our in-mine geologic conditions and to apply the knowledge gained to our mining operations. Two methods are used to collect information. The first is a monthly examination of conditions throughout the mine using a rapid mapping technique. The second is the detailed mapping of specific events encountered during mining such as faults and roof falls. The data gathered from both methods is correlated with operational statistics to create a geologic/production database. From the database, a monthly evaluation of mining conditions is made. Also, the database has proved useful in such areas as forecasting roof conditions and examining how faulting has affected mining operations.

Jan 1, 1984

By L. Bernoth, I. Firth, S. Rhodes, P. McAllister

As biotechnologies emerge from laboratories into main-stream application, the benefits they offer are judged against competing technologies and business criteria. Bioremediation technologies have passed this test and are now widely used for the remediation of contaminated soils and groundwaters. Bioremediation includes several distinct techniques that are used for the treatment of excavated soil and includes other techniques that are used for in situ applications. They play an important and growing role in the mining industry, for cost-effective waste management and site remediation. Most applications have been for petroleum contaminants, but advances continue to be made in the treatment of more difficult organic and inorganic species. This paper discusses the role of biotechnologies in remediation and pollution control from a mining-industry perspective. Several case studies are presented, including the land application of oily wastewater from maintenance workshops, the composting of hydrocarbon-contaminated soils and sludges, the bioventing of hydrocarbon solvents, the intrinsic bioremediation of diesel hydrocarbons, the biotreatment of cyanide in water from a gold mine, and the removal of manganese from acidic mine drainage.

Jan 1, 2000

By Lloyd W. Trevoy

Commercial production of heavy minerals from plant tailings streams is undergoing study by Syncrude Canada Lrd. When tar sand from an open pit mine is processed and up- graded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate consisting of a mixture of ilmenite, leucoxene and rutile, could be utilized as recovered or could be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for utilization.

Jan 1, 1981

By A. Acar, E. T. Tuzcu, Y. O. Vural

"In order to sustain the operations in chromite processing plants, due to concentrate selling cost, plants are in need of optimization in terms of capacity and recovery increase. In this study, DAMA Engineering carried out a methodological study for the purpose after a detailed sampling campaign in a plant which is situated in one the main chromite zones in Turkey; 1 The current status of the plant was investigated quantitatively with the bottlenecks, Plant overall efficiency in terms of recovery, Efficiencies of the particular equipment (mill, screen, gravity circuit), 2 A new circuit was proposed with the available equipment, 3 The new circuit that is product of modeling and experimental effort, was evaluated quantitatively as if it is a running plant, After 4-5 months continuous effort, the capacity of the plant was almost doubled (37 tph to 70 tph) and the plant overall recovery was increased from 48% to 63% by grinding adjustments and additional shaking tables theoretically. It was shown that the plant may move into profit with the minimum amount investment using readily available system. INTRODUCTION TO THE CURRENT PLANT The objective of the study is to increase the capacity and recovery of the chromite plant owned by Kurmel Group, Akmetal Inc. The complete study is given elsewhere (DAMA, 2016). The plant is situated in one of the main chromite zones in Turkey; Aladag. The current capacity of the plant is around 35 tph and the overall recovery declared by plant engineer is around 47 %. The chromite plant mainly has 3 units; crushing, grinding and gravitational circuits. The crushing circuit has 3 stages; a jaw crusher, a secondary cone crusher and a tertiary cone crusher operating in closed circuit with a vibrating screen with the aperture size of 15mm. In grinding circuit, a rod mill (2.44 6m x 3.6) and a ball mill (2.13 x 2.3m) are used for primary and secondary grinding, respectively. Derrick screens are used for the size separation. Additionally, for the size classification of the system, hydrosizers are used and each size fraction is sent to the shaking table sets. The middling product of the tables is subjected to re-grinding with a ball mill with the dimensions of 2.1 x 2.9 m. The capacity and the recovery are affected by several bottle necks; hydrosizers’ pure classification, primary/secondary mill power vs capacity problems, re-grinding product’s high slime content and so on. These combined factors made the plant to run in low recovery and capacity. Hence, DAMA was asked to make a study to investigate current status of the plant and propose a new solution to increase capacity and recovery of the plant. The conceptual flowsheet of the circuit is given in Figure 1 below."

Jan 1, 2017

By T. J. Harvey, W. van der Merwe, J. Joubert

GeoBiotics, LLC and Kumba Resources (Pty) Ltd are jointly developing the GEOCOAT® heap bioleaching technology and downstream processing technology for recovery of zinc from tailings at the Rosh Pinah Mine in Namibia. This paper outlines the development of a computer simulation for the bioleaching of sphalerite and the downstream processing. Computer modeling has shortened the product development cycle by allowing many flowsheet scenarios to be analyzed negating much of the expensive and time consuming laboratory testing. A model was developed using the Limn® system which is an Excel® Add-In flowsheet drawing and solution engine. Given that most engineers are familiar with Excel® this software is extremely easy to use and has less hidden calculations making model verification much easier.

Jan 1, 2003

By Daniel E. Collins

Massive banded Fe-Zn-Cu-Pb sulfide deposits in the Bagdad are associated with metamorphosed eugeosynclinal mafic volcanic and intrusives rocks Precambrian age. The geologic environment is very similar to that of the Jerome-Prescott area which lies 70 km. east of Bagdad. Mining of massive sulfides deposits began in 1917 on the Copper King mine in spite of its early discovery and the discovery of the Old Dick mine in 1882. The first shipments of zinc ore from the Copper King were hand sorted and averaged 46.89% Zn, 5.7 oz. Ag, 3.58% Pb and 1.68% Cu. Oxidized copper was first produced from the Old Dick mine in 1943~ In all, five deposits of massive sulfide ores have been mined in the Bagdad for a total production of nearly 2 million tons with an average grade of 12.0% Zn and 3.6% Cu. The largest deposit, the Bruce mine is currently closed because reduced metal prices and has produced a total of 823,000 tons of Zn-Cu ore to date. Mining of massive sulfide ore in the Bagdad area is presently idle. However, the potential for locating yet undiscovered ore bodies is good. Exploration for new ore bodies is difficult at best due to the complex geologic history of the area, the small size of individual ore bodies and lack of understanding as to the formation of massive sulfide deposits. The purpose of this investigation was to obtain a better understanding of the host rock formations through detailed geologic mapping, petrography and chemical analysis.

Jan 1, 1977