Search Documents

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By H. Zhu

Qualitative and interpretative information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system pro-vides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data.

Jan 1, 1989

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By A. Griffiths

The? use of hydrogen peroxide to detoxify gold mill waste waters containing cyanide and other toxic substances is already an established technology. Recent advances have extended the range of application of hydrogen peroxide treatment to include the removal of complex iron cyanides, the simultaneous removal of cyanide and toxic metals down to very low levels and treatment of barren bleeds, CIP' pulps and tailings pond discharges. Three treatment plants are described here. Each was installed at a gold mine in North America in 1987 and each illustrates a different application of hydrogen peroxide. The need for individual design of the detoxification plant to fit particular requirements is shown by the examples chosen.

Jan 1, 1988

By P. Bevilacqua, M. C. Williams, T. P. Meloy

We will bet you that, without prior programming within 10 minutes, we can design and simulate a 10,000 unit operation separation circuit. We will even do it at your place. We do it all the time. [ ] There are no tricks; we do it in a spreadsheet. We do it in those user friendly spreadsheet such as Quattro Pro. Spreadsheets must be user friendly. Accountants use them as do managers, business men, lawyers, doctors and salesmen. What these users seldom realize, is how powerful a mathematical tool a spreadsheet is. Among their other capabilities, spreadsheets can do a finite element analysis. That is why they are useful for accounting. That is also why they are more useful to engineers in the mineral industry. Spreadsheets are ideally suited for the engineering problems in the mineral industry. We have used then for solving problems in: a) mine ventilation; b) circuit design and optimization of dense media, flotation and sizing; c) comminution circuit design; d) shaking tables; e) Humphrey spirals; f) sluice ways and channel flow; g) lock particle and liberation problems; h) tunnel and shaft stress problems; i) cascadograph simulation; j) complex heat transfer problems; k) flow in porous media; and sheet flotation (Figure 1). Mineral industry problems presented on or with a spreadsheet are an excellent teaching instrument, problem statement and solution tools and sales devices. Spreadsheets answer easily, quickly and reliably many mineral industry engineering problems. What makes spreadsheets so useful to the mineral industry. The short answer is: they are easy to use; mineral industry problems fit the spreadsheet format. Those reasons are part of the answer. The real answer lies with the structure of the spreadsheet itself. Essentially, a spreadsheet is a "finite element analysis" form of computer software. Many mineral industry problems are readily solved by finite element analysis techniques. While some in the mineral industry may think they have never heard of finite element analysis, most use it weekly if not daily. Any profit and loss statement is essentially a finite element instrument. In fact, any array of numbers where one number is related to another may be construed as a finite element analysis product. Finite element analysis is a common daily activity. To get an appreciation of a finite element analysis, think of a monthly sales forecast for the next year. For each product and for each month, there exists a dollar figure for the forecasted amount of sales. In the forecast statement, for a given product in a given month, there is a "box" where the forecasted figure is presented. The forecast figure in that box was arrived at through some type of formula. The formula probably required some information from other neighboring boxes in the master forecast statement. Voila, one has a finite element analysis. Today the analysis would be done in a spreadsheet. A typical mineral industry problem is ventilation in an underground mine. Think of a rectangular room and pillar mining operation. Each room has air entering at a given pressure and velocity and air leaving at another pressure and velocity. During steady state, the air entering and leaving the room is determined by conditions in the adjacent rooms. One can readily model the room and pillar mine layout in a spreadsheet, and then find the flow in and out of each room at steady state. Change the flow by moving a brattice cloth or blocking off a path way and one gets a new air flow profile. Change the numbers on the spreadsheet that reflect

Jan 1, 1993

By Hans Smit

The face of mining as we know it is set to change in the very near future as mining companies all over the globe realize the implications of accessing the vast mineral wealth contained on, and under, our ocean floors. With some land based mineral deposits being fully exploited across the world, deep sea mining is set to revolutionize global approaches to the search for precious metals and other sought after minerals. [ ] Previously, the financial implications of deep sea mining outweighed the benefits of access to the mineral rich deposits identified all around the world. The process of marine diamond mining off the west coast of southern Africa started in the late 1950?s by a Texan, Sammy Collins, and subsequently continued by De Beers to the present day, has proven to be an excellent proving ground for the development of technology and mining systems that ensure a sustainable and financially viable business. [ ]

Jan 1, 2008

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By J. F. Childs

"INTRODUCTION Comprehensive overviews of the world-class talc deposits and related prospects in Montana were published by Olson (1976) and by Berg (1979). Both of these compilations include detailed descriptions and maps of the talc deposits and occurrences and were followed by a regional map and summary descriptions of the talc deposits published by Van Gosen et al. (1998). More recent publications, descriptions and field guides for some of the deposits include Underwood et al. (2014), Cerino et al. (2007), and Cerino (2002). The present paper focuses on some of the more recent ideas regarding talc formation that have developed since the publication of the earlier overviews. Olson (1976) reported that talc production from the deposits in southwestern Montana was over 200,000 tons in 1974 and that talc production had doubled between 1969 and 1974. The last year for which the U.S. Geological Survey published production records for talc by state was 1993. Production in Montana in 1993 was 350,000 tonnes (Virta, 1994). Remaining reserves are substantial at all three of the producing mines in the district. Minerals Technologies Inc., the parent company of Barretts Minerals Inc., stated in its 2014 annual report that it has reserves of 2,791,000 tons of talc. Imerys stated in its financial report for 2014 that it had 19,638,000 tons of proven and probable talc reserves at its North American mines. Although the Imerys reserves were not reported by individual mines or states, a large proportion of the total reserves would likely consist of the reserves at the Yellowstone mine, located south of Ennis, Montana. Talc mined in southwestern Montana is of high purity and is the quality used in a wide variety of applications including paints, ceramics, plastics, rubber, coatings, agriculture, cosmetics, and pharmaceuticals. GEOLOGIC SYNOPSES FOR MAJOR MINES AND COMMENTS ON REGIONAL DISTRIBUTION OF TALC OCCURRENCES The general geology of southwestern Montana is shown in Figure 1along with the locations of the three producing talc deposits in the area and the extent of pre-Belt marbles that host all of the talc mines and prospects. The term “pre-Belt” is used in the present paper because zircon and other radiometric data developed in recent years indicates that the metamorphic rocks that form the crystalline basement for the middle Proterozoic Belt basin in the Dillon Tectonic Block of southwestern Montana includes both Archean and Paleoproterozoic rocks (O’Neill et al., 1996; Foster et al., 2006; McDonald et al., 2012). An envelope or “corridor” has been superimposed on the geology in Figure 1 which encompasses all of the talc deposits that have a significant resource. This “talc corridor” will be discussed in later sections of this report. The more important talc deposits are discussed in this report section."

Jan 1, 2016

By Ehsan Moosavi, Kamyar Tolouei

In open-pit mines, the long-term production scheduling optimization problem (LTPSOP) is a complicated problem that contains constraints, large datasets and uncertainties. Due to its dimensions and NP-hard nature, it is usually difficult to find an ideal solution to the LTPSOP. The optimal schedule generally restricts the ore, metal and waste tonnages, average grades, and cash flows of each period. In this paper, to synthesize grade uncertainty into the strategic schedule, a stochastic integer programming (SIP) framework is presented to LTPSOP. The objective function of the SIP model is to maximize the net present value and minimize the risk of deviation from the production targets considering grade uncertainty simultaneously while satisfying all technical constraints and operational requirements. Instead of applying one estimated orebody model as input to optimize the production schedule, a set of equally probable orebody realizations is applied to synthesize grade uncertainty in the strategic schedule and produce a more profitable and riskbased production schedule. To solve the LTPSOP, the hybrid approach with the augmented Lagrangian relaxation method, the Harris Hawks optimization, the Random Forest method and Monte Carlo method was proposed. To indicate the applicability of the model, a case study on a gold mine was implemented. The framework displays the capability to minimize risk and improvement in the expected net present value and financial profitability .

Jun 25, 2023

By E. Zahl, J. Whyatt, H. Lawson

The U.S. Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03 in April 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB P09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2013

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By T. L. Carstensen

The Miami In-situ mine of BHP Copper is located in Globe-Miami, Arizona. The mine leaches mineralized leach capping over a supergene enriched sulfide deposit, and has produced over 500 million lbs of copper during the last 50 years. The Miami unit has identified several opportunities to enhance and expand in-situ production. A computer block model consisting of strict geologic controls, mineralogy, and metallurgical data was developed to assist in the determination of the leachable copper resource. An understanding of the accessibility and solubility of the resource to leaching solutions and the integration of hydrogeologic and hydrometallurgical information was necessary for completion of this project.

Jan 1, 1997

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

According to the Balandin's (1) "multiplet theory of catalysis", adsorption can occur only if atoms of the reactant molecules are congruent with surface atoms of the catalyst. Such a condition calls for certain definite geometrical relationships between the reactant molecules and the atoms at the surface of the catalyst. If such a match or geometrical 'fit' is not provided, the surface reaction will not take place. An appropriate analogy to this may be the lock and key theory that enzymes should fit a substrate just as a key fits a lock. Similar geometrical considerations in adsorption studies were made in connection with the flotation of minerals. Gaudin(2) and Gaudin and Preller (3) proposed that if the dimensions of collector ions are in registry with the mineral lattice, an ordered layer of adsorbed species is formed. They explained that the structural fit is one reason for good flotation of galena with xanthate. In another study, Bachmann (4) attributed the selective flotation of KC1 from NaCl with amine to the fact that the lattice parameter of the amine collector is closer to that of KC1. Schubert(5) investigated the flotation of various nonmetallic minerals with amine and pyridine, and related the dimensions of the collector ions with the anion distances of the mineral surface. He concluded that good flotation is obtained when the tolerance is within 20%. The geometrical theory has also been used by Groszek (6) to explain the preferential adsorption of n-paraffin onto the basal plane of graphite. The geometrical theory has thus been found useful in explaining adsorptive properties of an adsorbate relative to the substrate structure. The purpose of the present work is to examine the possibilities of a geometrical fit between sodium dodecyl sulfate and Cu(OH)2 surface, and to construct a crystallographic model of the surface compound.

Jan 1, 1974

By J. Bartrum

Kidston Gold Mines is a 14 000 tonnes per day rated operation located 280 kilometers west of Townsville in Queensland. The principle shareholder is Placer Development Limited. Kidston's orebody consists of 44.2 million tonnes graded at 1.79 g/t gold and 2.22 g/t silver. Production commenced in January, 1985, and despite a number of control, mechanical and electrical problems, each month has seen a steady improvement in plant performance to a current level of over ninety percent rated capacity.

Jan 1, 1985

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By J. P. Golightly

The structure and occurrence of nickeliferous laterite profiles are described and explained in terms of mineral solubility and drainage conditions. Complete profiles, from top to bottom, include: limonite zone; nontronite or silica zone; and saprolite zone. The middle zone is present only where drainage is sufficiently slow to allow saturation conditions to build up with resulting quartz or smectite precipitation. This precipitation may occur in any climate at a water table or in tropical climates with a long dry season. The degree of serpentinization of the laterite parent rock is important in determining the nature of the saprolite zone. Unserpentinized peridotite produces saprolite ores with hard residual rock cores, nontronitic or amorphous saprolitic rims, and fracture fillings of garnierite and quartz. Ser-pentinites yield relatively homogeneous serpentine saprolite, with minimal quartz or garnierite.

Jan 1, 1979

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.