Search Documents

By C. V. Deutsch, D. A. Silva

The geologic modeling of multiple domains is required for the prediction of mineral resources and reserves. In general, explicit methods have wide acceptance among modelers due to the ability to manually add deemed important trends and geological features into the models. As an alternative, implicit geologic modeling techniques are increasingly adopted to reduce professional time requirements. These methods aim for objective, repeatable and flexible models by replacing the manual time-consuming interpretation of sections with the interpolation of signed distance values. These techniques, however, have been developed for the binary case of two domains at a time. The current paper presents an algorithm that extends the binary case to multiple domains. The method is able to transfer large-scale geological features from data to geologic models. A case study illustrates the benefits of the algorithm and practical implementation considerations.

Jan 1, 2016

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By C. Basilio

Thermodynamic calculations based on a rigorous mass balance technique have been carried out for the chalcocite-potassium ethyl xanthate (KEX) system. The results of the calculations are used to: i) construct Eh-pH diagrams for KEX additions ranging from 0 to 10-4 M, ii) determine the amounts of cupric ions and copper xanthate formed at different Eh and pH values to make three-dimensional diagrams, and iii) determine the minimum KEX addition required to form CuX and CuX2.. This allows prediction of the optimum conditions for flotation and comparison of this with microflotation test data. In addition, voltammetry experiments have been conducted on chalcocite electrodes at pH 9.2 and pH 6.8 in order to gain information on the role of metastable species in flotation. On the basis of these experiments, possible reaction mechanisms are discussed and comparisons are made with what is expected on the basis of thermodynamics.

Jan 1, 1985

By Peter Halbach

Cobalt-rich ferromanganese crusts are one type of the two oxidic metallic mineral resources in the deep ocean that incorporate metals supplied and transported from both land (aerosols, continental run-off) and sea sources (oxygen-minimum zone, hydrothermal alteration of the oceanic crust). The substances directly precipitate from cold seawater under more or less oxic conditions and form thin layers (2 up to 25 cm thick) on hard substrate rocks like volcanic hyaloclastites, weathered basaltic rocks and/or carbonate-fluorapatite; in the crusts many metals therefore exist in the highest state of oxidation. Deposits of the Co-rich ferromanganese crusts are found throughout the global oceans on the flanks, terraces and summits of seamounts and submerged volcanic mountain ranges and platforms, where the ocean currents have kept the seafloor more or less free of sediment for millions of years. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical and surface-chemical mechanism. Elements in seawater may occur as dissolved hydrated ions or as inorganic as well as organic complexes which in general have either a positive or a negative surface charge depending on the pH of the respective aqueous environment. Those complexes may form hydrated colloids that interact with each other and with other dissolved hydrous metal ions. Hydrated cations such as Co, Ni, Zn, Sn are, for example, attracted by the negatively charged surfaces of colloidal hydrous Mn-oxide particles, whereas hydrated anions (e.g. oxyanions) and elements forming larger complexes with low-charge densities (e.g. U, As, Th, Hf, REE) are attracted by the slightly positively charged hydrous Fe oxihydroxide particles.

Jan 1, 2008

By M. R. Rosen

A technique is presented for simple characterization of the performance of flocculents in various mining applications. The method utilizes three key parameters obtained from raw settling data and combines them into a single athematical parameter called the desirability coefficient. The first two parameters are the timesrequired for the slurry-supernatant interface -to fall to two selected fractions of the starting height, and the third is the clarity of the supernatant liquid. The relative values of the three parameters may be assigned different weights in order to make them correspond with laboratory and field performance requirements of a particular industry. Provision is also made of an, internal comparison of test flocculant data with that of a control.

Jan 1, 1980

By Myron W. Mellor

Much has been published concerning the subject of coal preparation as related to electric power generation however it is always a most vital topic for both utilities and coal producers, It also constitutes a field of study that is never finished since new concepts and changing demands continually require altered perspectives. One graphic illustration that has been used to emphasize the rapidity with which times are changing is the fact that during World War I, a station that consumed 1000 tons per day was looked upon as a large central station, while today some single generators require 1500 tons during the same period, For further emphasis, at that time a 20,000 horsepower turbo-generator was a mighty large machine; today, a unit of this size is planned for driving the boiler water feed pump required for a single large main unit. During the past ten years alone, electric utilities have more than doubled their percentage of coal consumed as compared to the total market. They now account for approximately 40% of the United States consumption and one-third of all production including export, Conversely, approximately 70% of all U. S. steam electric generation is by coal and this percentage is expected to increase. It is further predicted that utility consumption will increase from the current 160,000,000 tons per year to between 400 and 500 million tons in 1975 which is approximately equal to todays total production

Jan 1, 1959

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980

By James E. Jones

The coal mining industry is being called upon to vastly increase production in the coming years. Many mining operations will have to prepare an environmental impact report of some kind and all will have to comply with various types of environ- mental regulations. Therefore there is a great need within the industry for access to environmental data, information, and literature. This paper discusses the informational resources available, the current lack of access to these resources, and the Environmental Data, Information and Literature (EDIL) Bank of the Kentucky Institute for Mining and Minerals Research. The bank's major emphasis concerns the environmental, social and economic aspects of producing clean solid, liquid, and gaseous fuels from coal. The data bank promotes information interchange between other related governmental and private projects and the energy development community.

Jan 1, 1976

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the important parameters influencing gold recovery. The model was used to direct modifications to plant operating practice. The cyanide-dosing strategy was changed to reduce gold losses from preg-robbing and to cut reagent consumption. A finer grind was achieved without capital investment. The density in the carbon-in-leach circuit was lowered, and tighter control was exercised over the plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz ($9.64/g) gold, and concomitant reagent cost savings of $55,000/ month.

Jan 1, 2000

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By R. L. Bonomi

Developing a mining venture in a foreign country, particularly in South Africa, can be a real challenge to those involved in the operation. The mining division of Southland Energy Corp. was asked to offer consultative support to the New Union Gold Mine, located in the Giyani District, Transvaal, Republic of South Africa, to aid in their expansion from an approximately 65 tonne per day exploration- exploitation project into a full scale mining operation of 300 tpd by January, 1987 with further expansion to 600 tpd by mid-year. This paper ad- dresses the development of the expansion plans, which are presently being implemented. History. Located in the Northern Transvaal, Republic of South Africa, the New Union Gold Mine is part of what is known as the Klein Letaba gold fields. Gold prospecting in the Klein Letaba gold field area dates back to the earliest years of European prospecting activities in the Transvaal where, reportedly, gold was discovered as early as 1887 (figure 1). The claims com- prising the present New Union Gold Mine have been explored by a number of individuals and relatively small mining groups since the early 1930's. The work done by these entities was aimed at recovering as much gold as possible in the quickest and cheapest manner possible and, as a result, the area was not explored in a systematic fashion. The long-term potential of the area, therefore, was not known until very recently.

Jan 1, 1987

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today's coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

By BEN WANG, HAORAN LI, YALI FENG, JINRONG JU

Acidic wastewater is at present directly neutralized with lime or limestone, which wastes resources such as titanium, scandium and iron and generates a great deal of solid waste. This study proposes a novel approach for the separation and recovery of titanium, scandium and iron from acidic wastewater, and utilization of red gypsum. The proposed process not only recovers valuable metals from acidic wastewater but also treats the red gypsum that has previously been dumped.

Aug 1, 2022

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By R. L. Beatty

Bond International Gold's Colosseum gold mine was discovered in 1865. No recorded production occurred, however, until the 1930s, with production of about 19 kg (615 oz) of gold. The mine was closed in 1942 as a nonessential industry during World War II. The property was acquired by Dallhold Resources in mid-1986. Construction of a 1.1-million Mt (1.2-million st), carbon-in-pulp (CIP), cyanide mill began in November 1986 and was completed in September 1987. Minable reserves are estimated to be 9.5 Mt (10.5 million st), with an average grade of 2.1 g/t (0.061 oz per st). This article describes the general process flow and plant equipment. And it looks at the maintenance and operational problems encountered in the first six months of operation. Process description Ore is direct hauled from the open-pit mine 1.5 km (1 mile) to the crushing facility. There it is crushed to -152 mm (-6 in.) with a single- stage, 1.5-m x 1.2-m (60-in. x 48-in.), 186.5-kW (250-hp), Fuller-Traylor jaw crusher. The ore is then stockpiled in a 31.7-kt (35,000-st) reclaim ore pile. Lime is added to the crushed product as it is conveyed to a single 6.4-m x 4-m (21-ft x 13-ft), Hardinge semiautogenous grinding (SAG) mill, followed by a single 4.3-m x 7.3-m (14-ft x 24-ft) Hardinge overflow ball mill. After grinding, the slurry is thickened and then preaereated for three hours. Following preaereation, the pulp is leached with NaCN at a pH of 11, also for three hours. The slurry then goes through a seven-stage CIP circuit for 21 hours. Then the tailings slurry is preaereated for three hours before cyanide destruction using the Inco process. Loaded carbon is eluted using an Anglo American strip, followed by electrowinning on stainless steel wire. The stainless steel wire is transferred to refinery cells where the gold and silver is plated on stainless steel plates. Following electrore-fining, the gold-silver foil is removed, melted, and poured into dore bars for shipment. The crushing, milling, refining, and maintenance processes require 37 people. Crushing The crushing area required changes and modifications following start-up. Several areas are of specific note. Structural failures Rubber support cushion blocks located under the coarse ore bin failed. These were replaced with heavier, more durable blocks and have since appeared to be satisfactory. A severe structural vibration was encountered in the entire crushing facility. A mechanical engineer, brought in by the contractor, determined the structure needed more support and cross-bracing.

Jan 1, 1989