Search Documents

By M. A. Reyes, L. Yan

Heat and humidity buildup withn refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a lifesustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ.

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) is used in the mining industry for early fire detection. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) have developed a direct method to calculate the fire heat release rate (HRR) when a mine fire is close to the AMS sensors, but this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire HRR using AMS sensor data at any location downstream of the fire. The method was validated using a full-scale diesel fire test conducted in the Safety Research Coal Mine at NIOSH’s Pittsburgh Mining Research Division.

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Heather Dougherty, Ted Klemetti, DYKE MARK VAN, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

By William Gleason

The Dulles Corridor Metrorail Project is a $3-billion project that will link Dulles International Airport with the downtown center of Washington D.C. by way of a single seat train ride. The project is mostly above ground, but it does include two short, yet complex, tunnels through the area of Tyson?s Corner. The project is being completed in two phases. The Dulles Transit Partners (DTP), led by Bechtel, was awarded the first phase, a $1.6-bil-lion phase that includes 17 km (11 miles) of track with five stations. At Tyson?s Corner, the project includes twin 730-m- (2,400-ft-) long, 6-m- (20-ft-) diameter tunnels. Bechtel is self-performing construction for the $1.6-billion design-build job. Gall Zeidler Consultants was hired by DTP as designer for the NATM tunnel portion of Phase 1, and Beton-und-Monierbau was hired as tunnel subcontractor. Tyson?s Corner is an affluent and congested area that sits 152 m (500 ft) above sea level. To get through the area, it was decided that tunnels would be the best option with the least amount of disturbance to the surrounding areas. However, with extremely shallow groundcover above some points as well as soft soil throughout, the tunnels are also the most complex aspect of Phase 1. About 213 m (700 ft) was constructed utilizing the cut-and-cover method. The remaining 518 m (1,700 ft) is being constructed using the New Austrian Tunneling Method, which integrates the principles of the behavior of rock and soil masses under load, and monitoring the performance of underground construction during construction. ?The tunnel only falls 2 m (7 ft) from one end to the other and we pass through two soil conditions, they are both soft ground,? said Dominic Cerulli, tunnel task manager for Bechtel. ?Soft ground is very tricky because you have to close the ring in a timely manner to minimize settlements at the surface. If you don?t close the ring quickly to achieve a round structure that?s good in compression, the tunnel could start necking and squatting and the ground above it will settle. We are under major roadways, so excessive settlement would be a bad thing.?

Jan 1, 2011

By Yong Pan, SRIVATSAN JAYARAMAN SRIDHARAN, Purushotham Tukkaraja

The block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found to be beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate the gas dilution situation when the source is located in the extraction drifts.

Sep 1, 2022

By Frederick T. Graybeal

Silver Bell is located about 56 km (35 miles) northwest of Tucson, AZ. It is a classic porphyry copper deposit containing enriched disseminated chalcocite ore in altered porphyritic rocks with chalcopyrite in adjacent skarn zones. The discovery of Silver Bell was an evolutionary process that occurred over a 75-year period. Recorded mining activity began about 1865 on Boot Hill east of El Tiro pit (see Fig. 1) where outcrops of altered limestones were found to contain 425 to 482 g (15 to 17 oz) Ag mixed with copper oxides. By 1874, the Young America Copper Co. was mining shallow occurrences of 30% Cu along the north side of the present Oxide pit. The ore was shipped by wagon to Yuma, AZ, and then by boat to San Francisco for smelting. By 1881, the district supported several mining companies, two small smelters, and was being favorably compared to Bisbee in local newspapers. Most of the ore mined in the period 1865-1903 came from pods of massive sulfide or their oxidized products which were distributed in an unpredictable fashion through a large skarn zone in Paleozoic limestone east of El Tiro pit. Ore grades varied from 5 to 10% Cu.

Jan 1, 1991

By S. S. Mauney

Natural and synthetic colors are used in almost every facet of our daily lives as a means of communication and expression. Natural ochres, umbers, hematites, and magnetites were once used in their crude or semi-processed state for their pigment value in construction products and low-end coatings applications, while yielding, in recent years, to synthetically produced iron oxides for more sophisticated products. Today, through innovative mining, processing, and marketing techniques, natural iron oxide pigments are once again gaining strong inroads into products and markets requiring precise chemical and physical characteristics. With our focus on environmental consciousness and resource conservation, value added natural iron oxides provide an economical and responsible alternative to our color needs.

Jan 1, 1993

By David A. Holmes

Zeolites are crystalline, hydrated aluminosilicates of the alkali and alkaline-earth metals. Their crystalline framework is based on a three dimensional network of SiO4 tetrahedra with all four oxygens shared by adjacent tetrahedra. The alkali and alkaline-earth cations are loosely bound within this framework structure and may be exchanged, to varying degrees, with other cations or molecular water. Most zeolites can be reversibly dehydrated. At present, close to 40 natural zeolite minerals have been identified and over 100 zeolites have been synthesized. Zeolites are a family of hydrous aluminosilicate minerals whose physical properties provide unique features for a wide variety of practical applications. Zeolites have been known for more than 200 years, but it was not until the middle of this century that their economic potential and widespread occurrence in sedimentary rocks were known. Since 1950, literally thousands of articles and patents have appeared in technical literature, and commercial pro¬duction of natural zeolites may now exceed 1 Mt worldwide an¬nually. In the past 40 years, the zeolite mineral group has changed from that of a museum curiosity to one of an established industrial mineral commodity. According to Breck (1974), zeolites are characterized by the following properties: 1) High degree of hydration, 2) Low density and large void volume when dehydrated, 3) Stability of the crystal structure of many zeolites when dehydrated, 4) Cation exchange properties, 5) Uniform molecular-sized channels in the dehydrated crys¬tals, 6) Ability to adsorb gases and vapors, 7) Catalytic properties. All zeolites are molecular sieves, but not all molecular sieves are zeolites. Activated carbon, activated clays, alumina powder, and silica gels are also molecular sieves. Molecular sieves are materials that can selectively adsorb molecules on the basis of their size, shape, or electrical charge (Clifton, 1987). Commercial application of zeolites is based on the following physical properties: molecular sieving, ion exchange, adsorption, and catalysis. Potential commercial utilization includes hundreds of possible applications. The principal uses at this time, however, are as fol¬lows: -Ammonium-ion removal in waste stream treatment, sewage treat¬ment, pet litter, and aquaculture, -Odor control, -Heavy metal ion removal from nuclear, mine and industrial wastes, -Agricultural use, such as soil conditioner and animal feed supplement. An estimated 800 kt to 1 Mt of natural zeolites were produced and consumed worldwide in 1991. Eight small operators reported collective production and consumption of an estimated 18 kt of natural zeolites in the United States during 1991, mostly for feed additives and for odor control, aquacultural, agricultural, catalytic, and ion exchange applications (Eyde, 1992).

Jan 1, 1994

By R. F. Kovar, R. N. Torbin, R. E. Gundersen

I have to express my .surprise and must send a note of warning concerning the use of polyurethane foam as described in a paper by R.N. Torbin and R.F. Kovar, entitled "Innovative Shaft Lining Method," published in your February 1989 edition. In September, 1986, 177 miners lost their lives when they were exposed to fumes downwind from a fire in a tunnel lined with polyurethane foam. Whilst polyurethane exhibits reasonable fire retardent properties in small-scale tests, mass use in a tubular configuration, exacerbated by the furnace effect of cross-radiation, can lead to a rapid, uncontrollable conflagration. I do not wish these comments to detract from the engineering achievements of the authors but rather to sound a loud warning as to the application of the system. Any shaft designed for human access- be it for transport or shaft work - and any intake airway, should not consider the use of polyurethane foam. It only needs a slip with a cutting torch or an electric fault to initiate a disaster. Many countries have banned or restricted the use of polyurethane foam in the workings of a mine and maybe alternative foams (e.g. phenolics) can be used or developed

Jan 1, 1991

By C. C. Muir

At the outset, I believe reference should be made to comparatively recent world developments in copper which have an important bearing upon the Canadian position. COPPER SITUATION No one can doubt the marked change for the better compared with not so long ago when less than adequate attention was paid to marketing and to uses of the metal. I need not show you graphs of world copper prices, which except for relatively brief periods and war conditions were, until about three years ago, not unlike the topography of the Canadian Rockies. There remain, of course, some non-industry factors who yearn for the old days of "roller-coaster" copper prices.

Jan 1, 1964

By D. Gu, B. Lin

Discussion of concept Breakage of rock by machine is one of the major methods of excavation. With the development of modern engineering techniques, the advantages of using this method have become even greater. Improving efficiency and reducing the cost of rock breakage is the main goal of mechanizing the rock-breaking operation. For a given stratum, the efficiency of a machine excavation depends, to a large extent, on the design and method of application of the tools used. In a planetary cutter head, the subcutter heads move like planets around the main drive shaft. The general structure of the cutter head is shown in Fig. 1. As shown in this illustration, the main drive shaft (1-1) is connected to the tie bar (1) and, thereby, to a gear (5) that meshes with a fixed-gear ring (2). The subcutter head (4) is rigidly connected to the gear (5) by the subcutter-head axis (2-2). When the main drive shaft (1-1) rotates, the subcutter head (4) rotates around the axis (2-2), under the action of the tie bar and with the help of sleeve pipe (3). At the same time, axis (2-2) also rotates around the main shaft (1-1). As shown in Fig 1, [a] is the angle between the main shaft and the subcutter-head axis. This angle determines the shape of the drilling face. If [a] equals zero, the drilling face will be a flat surface (Fig.1 (a) ), and if [a] is greater than zero, the drilling face will be a spherical surface (Fig. I (b)). For a planetary cutter head, the most important design parameter is the transmission ratio (i), which is defined as [i = (0210)1(1)] Where [(a] is the angular speed of rotation of the subcutter heads around their individual axes, and [o] is the angular speed of rotation of the subcutter-head axes around the main shaft. In Eq. (1), i is positive if the direction of rotation of a subcutter head around its axes is the same as the direction of rotation of the subcutter-head axes around the main shaft (see Fig. 1(b)). Conversely, i is negative when the two directions are opposite (see Fig. 1(a)). When i is positive, the cutters on the subcutter heads form epicycloid paths on the drilling face, as shown in Fig. 2(a). Conversely, if i is negative, the paths will be hypocycloid, as shown in Fig. 2(b). It should be noted

Jan 1, 1996

By H. A. von Schonfeldt, H. Douglas Dahl

INTRODUCTION During the past decade, significant pro¬gress has been made in applying rock mechanics principles to mine design problems by a great number of researchers. Some of these new techniques have found their way into the engineering and planning offices of the operating mine. In spite of these advances, however, the application of rock mechanics in the day-to-day mine planning and design of our domestic coal mines is rela¬tively rare. There are a number of reasons responsi¬ble for this relatively slow progress, not the least of which is the question of how to measure the success or cost effectiveness of a sizable rock mechanics effort in an opera¬ting mine. Firstly, the properties of geologic materials generally vary over a wide range and it is, therefore, difficult to assess whether an improvement in the mining conditions is due to a design change or due to a change in the geologic conditions. A second reason for the slow acceptance of rock mechanics in engineering thinking is the fact that some of the concepts are quite difficult and that physical evidence of their validity to mine design is still rare. Thirdly, com¬munication between research, engineering and applications oriented people appears to function only intermittently. In our view, however, the most important impediment lies in the "state-of-the-art." Exactly how much can rock mechanics help the mine operator? The best that rock mechanics can do at present is determine whether one approach is better than another when weighed against some design objective (stress, strain, deformation). We cannot determine the abso¬lute best ground control design -- only what is better. If ground control is lost, the statement that "it's the best one we looked at" means very little to the harried operator. While the "state-of-the art" has advanced a great deal, it has certainly not been reduced to an engineering matter in that design hand¬books are available -- they are not. The success of a rock mechanics program, there¬fore, can be determined only over a long period of time of continuous effort.

Jan 1, 1977

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By D. Legg

This is the first in a series of studies commissioned by the European Environment Agency that aim to raise awareness of the use of economic instruments and assess their effectiveness. The emphasis is on sharing good practice and increasing knowledge and understanding across European countries in this emerging policy area. A methodology for evaluating the effectiveness of economic instruments has been developed and this will examine whether the inclusion of economic instruments in complex policy packages can improve the overall performance, particularly as a prevention tool in terms of resource use and waste generation The focus for this initial study is the use of aggregate taxes in four EU countries which include the Czech Republic, Italy, Sweden and the UK so that a range of experiences (e.g. geographical, political etc.) can be included. The findings will be used to inform and influence future policy development in other EEA countries. The methodological approach is divided into two main sections: - Technical analysis, which covers quantitative and qualitative analysis. - Process design, i.e. who should be involved when, where and how. Process design is essential if the full learning benefits are to be gained from the technical analysis, which is the ultimate objective of these evaluations.

Jan 1, 2007

By Erik Sundström, Magnus Nygren

The study explores the influence and consequences of safety initiatives on the development of safety cultures in the Swedish mining industry. It involves interviews with experts from four mining organizations, highlighting themes such as organizational structures, safety leadership, feedback, and communication.

Nov 1, 2023

There are many risks associated with the storage of nuclear or other toxic wastes. One of the major risks is the escape of material from the repository. No matter how well a storage facility is engineered, the potential escape of dangerous material must be studied. This kind of study will include some estimation of the "travel path" of the particles. The travel path of a radio-nuclide particle will depend on the geological and hydrological parameters of the surrounding rocks. These parameters must be estimated from a limited number of samples available within the study area. Any estimation will -of necessity -contain a certain amount of uncertainty or "estimation error". This uncertainty will be carried through to the analysis of potential movement of particles, so that the estimated travel path itself will be subject to some error. This paper discusses an approach which may lead to a quantification of the uncertainty on the predicted travel path.

Jan 1, 1989

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

By Yong Yuan, Wenhao Xiao, Luc Taerwe

"The static shear stiffness of an immersion joint subjected to combined compression and shear forces is investigated by experiments in a test set-up. To explore the performance of the immersion joint, the compression-shear loads, which are applied on a specimen according to test protocol, are determined based on real design situation. In this test, the main focus is on the steel shear keys and the rubber sealing. For the applied loading schemes, different levels of axial force, corresponding to the water depth of the joint, are considered as well as the changing amplitudes of the shear force. The force-displacement curve is obtained and the hysteresis is observed during the whole test. The joint‘s static shear stiffness is calculated, showing to increase linearly with respect to the magnitude of the axial force. Moreover, it is found that the rubber sealing has a significant influence on the shear behavior of the joint. INTRODUCTION An immersion joint is the connecting part between two adjacent elements of an immersed tunnel. Compared to that of the bulk elements, the stiffness of the immersion joint is relatively small. When it is subjected to shear actions, whether resulting from vertical foundation settlement or horizontal earthquake movements, shear-resistance of the joint is the main concern for a safe and reliable water-proof design. A flexible immersion joint, which normally consists of a rubber seal and shear keys installed at an element end is a common solution in practice. The way in which the shear keys and the rubber seal behave in the joint together is of vital importance to a comprehensive understanding of the shear behavior of the joint. However, in literature very few experiments on the shear behavior of immersed joints are available although the flexible joints are applied in practice for more than 50 years already. O. Kiyomiya (2004) carried out both a 3-dimensional experiment and a finite element analysis for a new type of flexible joint referred to as the Crown Seal. The results indicated that this new type of joint can be applied in practice because of the effective reduction of lateral deformation. A linear model was found in the paper of Anastasopoulos et al. (2007) to describe the behavior of the shear keys, which consider that the stiffness of the shear keys tends to infinity. R.S. van Oorsouw (2008) discussed the shear capacity of concrete shear keys in segmental joints, by analyzing the influences of reinforcement and friction force between shear keys."

Jan 1, 2016

By J. Gauntt

Calcium carbonate is one of the most widely used industrial minerals in applications like cement, lime, agriculture, power plant fluegas desulfurization (FGD) and construction aggregates. Most applications are generally high-volume and low value ($9/t or $10/st) or less free-on-board (f.o.b.) mine site) uses of this material. Specialty uses of ground calcium carbonate (GCC) are typically referred to as ?performance mineral? or ?extender and ?ller? applications. Primary specialty markets for GCC include paper and plastics as well as a number of construction applications including joint compounds, carpet backing, paint, and adhesives, caulks and sealants (ACS). Other important specialty applications for GCC include rubber, food and personal care products. A new and growing application for GCC is in nonwoven fabrics, where this mineral replaces a small percentage of the polymer. Typical specialty applications for GCC are color sensitive and require extremely white/bright materials. Although deposits of limestone are located in most states, high brightness resources are relatively rare and controlled by a limited group of suppliers.