Search Documents

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By Theodore Balberyszski

The gradual depletion of high-grade sulphide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of non-sulphides possible, although in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulphidize the surface of the relevant oxide mineral and thus make it amenable to flotation. (1) (2) (3) In recent years, Bautista and Sollenberger(4) have investigated the conversion of a number of oxides to sulphides by reacting them with molten sulpur. This paper presents the results of investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulphidized minerals. It is divided into two parts; Part I describes the sulphidization of a number of oxides and a silicate, and Part II presents the flotation behavior of the products of sulphidization.

Jan 1, 1968

By Thomas Pollard

It is truly remarkable how the image of longwall as a method of mining has changed. Between 1920 and 19609 viewed on a world wide basis, longwall was regarded as a' system for difficult and deep conditions and associated with intensive labour extraction. Today the world looks on longwall in the hope that it can produce the next really big break through in productivity, Three correlated machinery developments have made this possible, but it is not only the machinery developments, interesting though these be in themselves, but together with developments in control systems of these machines that longwall now looks so much more attractive, The machinery concerned is, of courses:- 1. The Anderton Shearer Loader - A miner that takes a narrow strip off the, face at rates acceptable to modern mining engineers. 2. An Armoured Flexible, Conveyor which can be kept in close contact with the face and still convey coal as it is snaked over to the faces 3. Powered support systems which can be mechanised and controlled with reliability at any distance from the individual support itself.

Jan 1, 1964

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By Kenneth S. Johnson

Oklahoma is a region of complex geology where a mobile belt of Paleozoic geosynclines and uplifts on the south abuts against the margin of the North American craton to the north. The state contains many classic areas where fundamental concepts of sedimentation, stratigraphy, structural geology, historical geology, mineral investigation, and petroleum exploration have been formulated through the years. In the southern Oklahoma mountain belts, there are exposed a great variety of igneous and sedimentary rock units seen at few other places in the Midcontinent area. Major geologic provinces of Oklahoma (Fig. 1) include: (1) the cratonic and relatively stable northern shelf areas, including the Ozark uplift; (2) the Ouachita geosyncline (now the Ouachita Mountain belt) and associated Arkoma basin in the southeast; and (3) the southern Oklahoma aulacogen (geosyncline), comprising the area of Anadarko, Ardmore, Marietta, and Hollis basins, as well as the Arbuckle and Wichita Mountain uplifts. The three principal fold belts, the Ouachitas, Arbuckles, and Wichitas, all originated from a series of Pennsylvanian orogenies (about 300 million years ago) in the two Paleozoic geosynclines.

Jan 1, 1999

By J. M. Stewart

The incidence of heat stroke in the South African gold mining industry is today small (less than 1 in 10 6 shifts worked). Acclimatization and selection procedures have been developed and applied throughout the industry, underground working conditions have, and are being improved, and personnel are to-day made more aware of heat stress and its consequences than ever before. Although these actions have, over the years, brought about a steady reduction in the incidence of heat stroke (see Figure 1) the small incidence of heat stroke which persists indicates that heat stress is still a problem. This realization provides the stimulus for the work presented in this paper, which has as its primary objective the development of reliable heat stress limits for men working in South African gold mines. [ ] In keeping with recent trends3I4 the approach followed in this paper is based on the physical principles of heat transfer. Detailed studies of heat transfer from humans have been undertaken,5-l1 and certain of the results form an important aspect of this Paper -

Jan 1, 1980

By R. Hogg, L. G. Austin, R. C. Klimpel

Slurry densities and holdup were measured for open circuit grinding tests in a laboratory overflow ball mill of 0.3 m diam by 0.6 m long, by emptying and drying after stoppage of the mill. Contrary to some other results in the literature, there was negligible variation of slurry level in the mill as a function of flow rate over a range of increase of flow rate of about 5 to I. However there was a gradual increase of solid holdup at higher flow rates because the slurry density in the mill increased. Equations are given for holdup and slurry density in the mill as a function of over flow diam, ball load, and feed slurry density. The average level of slurry necessary to give over flow was found to be much higher than that necessary to fill the mill to the overflow level at rest. The total level of balls and slurry was only increased slightly by ball loads higher than the overflow level. The overflow diam appeared to be the major controlling factor in determining the mill holdup.

Jan 1, 1990

By Thorvald Wetlesen

Computer controlled drilling is now proven technology. It was first introduced by the development of the Furuholmen system for a prototype three boom tunneling jumbo in Norway in 1978. Now, 13 rigs with this concept are in operation in Europe, 3. in mining in England and. 10 in tunneling elsewhere in Europe. The system is also adapted to roadheader guidance. Practical experience has shown that the computer control system makes it possible to drive tunnels with a more accurate contour thus reducing the total amount of rock excavated, and where a full concrete lining is required a reduction in concrete volume is achieved. The total tunneling economy is improved. In the future we expect to see a wider range of instrumentation on jumbos, from the simple direction instruments to computer guidance systems for monitoring only, as well as fully automatic drilling to a programmed drilling pattern. More compact and reliable electronics will be available. Systems with low power consumption will fit easily into flameproof applications. Cabling complexity will be reduced by connection of sensors to serial signal lines.

Jan 1, 1989

By Noris Del Be1 Belluz

Drilling underground in the Grasberg dewatering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are used. Pilot holes probe ahead of the tunnel development to intersect aquifers ahead of the face. And dewatering holes dewater rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, static pressures of >8.3 MPa (> 1,200 psi) have been recorded with flows from a 100 mm (4 in.) HQ core hole measured at 5,700 L/min (1,500 gpm). The waterflows can be slightly acidic, necessitating the use of stainless-steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early on to deal with these conditions. PT Freeport Indonesia (PTFI) established procedures to maintain the safety of the drill crews, to enable coring of the rock, and to maintain the safety of the miners driving the drifts. The collar gear controls the waterflows because these drill holes are a vital source of water for the concentrator.

Jan 1, 1998

By Hasan Sevim

A computerized heuristic model for an efficient and economic design of belt haulage networks in underground coal mines is discussed. The model is versatile, easy to use, and is valid for all mining methods singly or in combination. It may be used to design new networks or to analyze existing networks. The input data required are 1. maximum production rates from a section, 2. probabilities of production rates, 3. equipment costs, and 4. data necessary for network coding to represent different cases. The objective function is the "expected minimum cost per ton of coal hauled" while meeting production requirements. The output includes belt width, motor horsepower, bin size etc. and also values of operating parameters for each belt such as belt speed, effective tension, power consumption etc. A detailed account of the cost involved is also provided for each unit as well as for the entire network. Description of the model and an example of the design of a belt network in a mine with two longwall and four development sections are presented.

Jan 1, 1986

By A. E. Hall, K. R. Mutama

The wind tunnel has been used extensively for mine ventilation research and continues to be a valuable tool. The advent of the powerful personal computer has reduced the use of wind tunnels because several flow problems car be simulated and investigated quickly. This paper describes the recent design and construction of a wind tunnel which is now being used for mine ventilation aerodynamic research and teaching purposes. The wind tunnel has a square cross section measuring 900 by 900 mm and is 8485 mm long from the entrance to where it joins the fan. The tunnel was designed as an open circuit suction type and is attached to a 7.5 kW variable pitch axial flow fan capable of producing over 6 m3/s of airflow. The entire length of the wind tunnel can be used for flow investigations and all activities are visible since the sides are made of plexiglass. Results are presented from the test program to show that even without honeycombs and screens air flow symmetry is achieved.

Jan 1, 1993

By R. E. Johnson, J. E. Dutrizac, B. R. Palmer

Silver sulphide (acanthite) and lead sulphide (galena) dissolve relatively rapidly in FeCl3 media with the formation of elemental sulphur and soluble silver and lead chlorides. Parabolic kinetics are observed, and the leaching rates are controlled by the outward diffusion of the AgCl and PbCl2 reaction products through the constantly thickening elemental sulphur layer formed on the sulphide. Hence, both leaching rates are strongly dependent on those variables which affect the solubility of AgCl or PbCl2 at the reaction interface. The rates therefore increase with increasing temperature and total chloride ion concentration, but decrease in the presence of elevated concentrations of AgCl or PbCl2. By contrast, neither sulphide is significantly attacked by ferric sulphate media, even at high Eh values. Although the reasons for the refractory behaviour of Ag2S in sulphate media remain unknown, the low rate of PbS attack is attributable to the passivating layer of PbSO4 and elemental sulphur formed on the surface of the galena.

Jan 1, 1993

By O. Alvarez-Campos

Two porphyry copper orebodies, the North and Central MM orebodies, have been found through regional and structural geologic works, about 5 Km south of Chuquicamata, under a gravel bed of approximately 100 m and in the west side of the West Fissure. The mineralization is emplaced in a coarse granodioritic porphyry, predominantly with sericitic alteration. In the North MM ore-body, with 200 million metric tons of 1.0% Cu, the mineralization is mainly chalcopyrite, bornite, digenite and molibdenite. In the central MM orebody, with 700 million metric tons of 1.3% Cu, there are large veins of enargite, chalcocite and bornite, the last one increasing in depth, separated by chalcopyrite and pyrite zones; in these veins there are interesting gold and silver values. Both orebodies have an upper enrichment of chalcocite and covellite, with pyrite envelope. According with these characteristics, the MM orebodies could he the upper part, with sericitic alteration, of the Chuquicamata porphyry copper system, displaced by the West Fissure system movements, but we couldn't eliminate the possibility that MM can be a new orebody, different of Chuquicamata.

Jan 1, 1993

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By Leonhard Schmid

INTRODUCTION In the region of Zurich several of the Swiss Interstate Highways meet and have to be linked to form a continuous network. The subalpine glacial topography with hills, ridges and lakes requires the construction of many tunnels (Figure 1). The Milchbuck Tunnel forms part of the inner arterial highway system of the city of Zurich. It passes underneath the ridge separating the Limmat and Glatt valleys. In its final configuration the tunnel will consist of two parallel three-lane tunnels (Figure 2). For the time being only one tunnel is constructed. This tunnel will be operated with two outbound (climbing) lanes and a single inbound (descending) lane (Figure 3). The owner, the Canton of Zurich, awarded the contract for the construction to a joint venture with the following three contractors: Locher & Cie AG (leader), Prader AG, A. Brunner's Erben, all located in Zurich. The actual freezing was performed by subcontractor Philipp Holzmann AG, Mannheim, West Germany. Electrowatt Engineering Services Ltd, Zurich, was design engineer and performed the construction supervision.

Jan 1, 1981

By J. A. McKeown, B. M. Sanders, A. Dadgar, R. H. Sergent

This paper describes the leaching of gold with Geobrom® 3400 from a very rich (6.2 kg/tonne) black sand concentrate and its subsequent recovery by ion exchange resins and solvent extraction. The dissolution of gold from black sand ranged from 94 to 96%. Gold loadings and recoveries of nearly 100% were achieved by both ion exchange and solvent extraction methods. The kinetics and equilibrium of loading gold onto ion exchange resins and its elution from the resin were studied. The commercial ion exchange resins PAZ®- 4, DOVEX®- 21K, and Amberlite® XAD- 7, and Great Lakes Chemical experimental GLR-30 were evaluated in this work. Diethylene glycol dibutyl ether was used in all the solvent extraction work for gold recovery from Geobrom leach solution. The consumption of Geobrom was about 130 kg per tonne of the concentrate processed. Therefore, the cost of lixiviant to extract 3.11 x l0-2 kg of gold from the black sand was only about $1.00. Based on the electrochemical regeneration of bromine, the economics of bromine process vs. cyanidation were investigated.

Jan 1, 1990

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995