Search Documents

By Manuel Arnáiz, Pedro R. Sola, Rogelio Baudot, Manuel Herrera, Carlos S. Oteo

The aim of this paper is to describe and analyze the ground treatment performed between January and May 2002 in order to increase safety during excavation and reduce instability problems along 180 m of tunnel, during the construction works associated with line 10 extension to the Madrid Metro. The tunnel was excavated using the traditional Madrid Method and in the section considered in this paper layers of sand were detected around the tunnel crown area with a significant presence of water, the in?ow of which needed to be controlled with a minimum impact on the surrounding environment.

Jan 1, 2003

By P. J. Closmann

Steam zone growth as a function of time has been calculated for the case of constant rate steam injection into a preheated reservoir. To simplify the calculation a linear temperature profile has been assumed in the cap and base rock at the start of steam injection. The results indicate that at early times augmentation of steam zone growth due to preheating should be greatest. At longer times the steam zone development becomes close to that calculated with no preheating. INTRODUCTION With the increasing application of thermal recovery processes to recover viscous oil, cyclic steam injection has become important in many large-scale projects. In this process, the cycle of steam injection followed by oil production is repeated a number of times. At the beginning of the second and later cycles, steam is injected into a reservoir that has already been heated but that has lost part of its heat both in produced fluids and by conductive heat loss away from the injection zone. In such a case, the temperature level of the injection zone and the temperature distribution of the surrounding rock will affect the growth of the steam zone developed during the subsequent steam injection. Knowledge of the size of steam zone developed is important in determining the amount of oil displaced and the extent of heating in the reservoir. It is also useful to be able to compute the size of the steam zone for cases where thief zones take most of the injected steam. This paper presents a fairly straightforward method of estimating the steam zone developed in a preheated formation, based on certain simplifying assumptions. Some cases of steam injection into a reservoir at its original temperature have already been considered elsewhere.1-3 Because it is difficult or impossible to obtain an accurate representation of the temperature distribution in the reservoir some time after initial heating has taken place, in this work, a linear temperature profile in the cap and base rock is assumed (Figs. 1A and 1B). The linear profile has the advantage of yielding heat flow equations that

Jan 1, 1969

By N. A. Pace

This is one of a series of papers being published by the Federal Bureau of Mines for the dissemination of information on methods and practices used in the mining and preparation of crushed stone for market requirements. Performance in terms of units of work or tons produced per machine and per operator man-hour are given whenever that information is available. Direct operating costs are useful for comparing different methods, and are, therefore, included if possible. In addition to the factual description of equipment and methods used, it is desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with the opertions at the Columbia plant of Palmetto Quarries Co. of Columbia, S.C. The plant is about one-half mile east of the Congaree River and adjacent to the southwest corner of the city of Columbia. Rail access is by the Atlantic Coast Line Railroad, and by a spur strack of the Seaboard Airline Railroad.

Jan 1, 1962

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By John W. Taber

The Bohemia mining district is a small but intensely mineralized area in western Oregon . For its size , it has made a substantial although somewhat sporadic production of gold throughout a long period of years . The veins also contain lead, zinc , and copper, but in the past these metals have not been recovered in important amounts . In reviewing the progress of mining activity in the district , an effort has been made to gather under one cover all available information on former operations , including methods of mining , production, and geology pertinent to the ore deposits , problems encountered, and other factual data that may affect future mining in the district . A special effort has been made to assemble as many maps of former workings as possible in order that these may be preserved and readily available to assist in future exploration. The data presented herein are based on brief reconnaissance examinations made during several weeks spent in the field in September 1946. These are supplemented by information obtained from various individuals actively or formerly connected with operations in the district . Only the principal properties and several of the more outstanding prospects were actually examined. Many of the older workings were inaccessible.

Aug 1, 1949

By Matheus Teixeira Fraga

É comum o uso de modelos matemáticos no intuito de prever a qualidade do coque, sendo a maioria dos modelos atualmente disponíveis baseada nas propriedades dos carvões. Para este trabalho foram feitas misturas binárias e ternárias de carvões com variados teores de matéria volátil, a fim de se produzir coque em escala laboratorial. A reatividade ao CO2 em termobalança e resistência mecânica em tambores foi avaliada. Dois modelos para previsão de indicadores de qualidade do coque foram avaliados, o modelo aditivo e o modelo de interação. A partir da metodologia desenvolvida em laboratório foi possível produzir, avaliar e comparar coques feitos a partir de diferentes carvões e misturas. O modelo aditivo mostrou uma boa capacidade de prever a reatividade dos coques. No entanto, para os índices derivados dos testes de tambores os valores calculados mostram uma diferença importante em relação aos experimentais, indicando interação dos carvões no processo de carbonização. Nos resultados do modelo de interações, os valores calculados para reatividade e resistência mecânica, se comparados com os resultados do modelo aditivo, mostraram uma melhora na capacidade de previsão da qualidade do coque. O modelo de interações se apresenta como uma ferramenta interessante na seleção e mistura de carvões.

Aug 17, 2017

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By Bráulio Campagnaro Santana

Na indústria da mineração, a liga Fe-Cr-C destaca-se como um revestimento duro em chapas de desgaste objetivando aumentar a vida útil do ativo. Três ligas, duas delas contendo Fe-Cr-C, sendo uma com aproximadamente 28% (p) de Cr e outra com 38% (p) de Cr e uma terceira liga com 24% (p) de Cr e 7,0% (p) de Nb foram levadas a ensaios de desgaste abrasivo roda de borracha conforme norma ASTM G65-04, além de medições de dureza, microdureza e caracterizações microestruturais. Constatou-se que os revestimentos contendo Nb, depositados com uma ou duas camadas de solda, possuem maior resistência ao desgaste abrasivo, seguidos pelos com maior teor de Cr. Os revestimentos que possuem maior fração volumétrica de carbonetos, finamente distribuídos na matriz, apresentaram os melhores resultados na resistência ao desgaste. Analisando no microscópio confocal 3D os revestimentos contendo Cr, notou-se que os mecanismos de desgaste são do tipo microcorte e microssulcamento, enquanto naqueles contendo nióbio prevalece o desgaste por rolamento em boa parte da superfície. A liga contendo Nb apresenta o melhor desempenho na resistência ao desgaste abrasivo em relação às demais, e se torna viável economicamente sua aplicação na indústria.

Oct 30, 2017

By K J. Thompson

This paper describes the work which has been undertaken at the Ohai coalfields in Southland to restore overburden heaps during past opencast mining operations, and procedures which have been adopted to ensure that restoration is achieved concurrent with present opencast mining activities. The system implemented for the treatment of wastewater from opencast mining operati6ns is also described.

Jan 1, 1981

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By A. R. Biggart, A. Walters, G. J. E. Kramer

The Owner Procurement Process or OPP is a proven, viable alternative contract delivery method that is potentially applicable to many tunnel projects. Using the OPP, the owner specifies and procures major tunnel construction items such as tunnel boring machines and tunnel linings and provides them to a tunnel excavation contractor in order to manage risk and accelerate project schedule. However, due to industry perceptions regarding potential owner risk, it is seldom considered or is rejected out of hand. In fact, past performance demonstrates that the process significantly minimizes owner, contractor and over-all project risk and mitigates the impact of any claims and differing site conditions. The paper outlines how the process should be structured to achieve schedule, cost, quality and risk management benefits. Potential and perceived disadvantages are discussed and how the process can be structured to mitigate or avoid them. The planned implementation of this process on the tunnels for the Silicon Valley Rapid Transit Project in San Jose, California is discussed.

Jan 1, 2005

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

By Jayant Khambekar

In a typical mining operation, run-of-mine (ROM) ore is crushed and screened to achieve a desired particle size distribution and then fed to processing equipment for further refining. For an operation to be profit-able, the ore handling system from the mine face to final product loadout must be reliable. However, the handling system components do not always perform as expected and production problems related to material flow occur. These problems include flow stoppages, limited live storage capacities, uncontrollable flow, segregation, spillage and dust emissions. These result in lost production, excessive maintenance, safety and environmental issues, and even structural failures, in some cases. Flow patterns Flow problems and their solutions can be best understood by first learning how bulk solids flow. As bulk solids discharge by gravity from a storage system, primarily two types of flow patterns can develop: funnel flow and mass flow. Figure 1 shows a schematic of these two flow patterns. In funnel flow, only a portion of the material is in motion during discharge, which flows toward the outlet through a channel that forms within the stagnant material. Funnel flow occurs when a hopper is not sufficiently steep and smooth to ensure flow along the walls or when the outlet is not fully effective. In mass flow, all of the material is in motion whenever any is discharged ? there is no stagnant material. Mass flow occurs when the hopper is sufficiently steep and smooth to ensure flow along the hopper walls. Shallow valleys are not permitted and the outlet must be fully effective. A third type of flow pattern, called expanded flow, can develop when a mass flow hopper (or hoppers) is placed beneath a funnel flow hopper or bin. The mass flow hopper is designed to activate a sufficiently large flow channel in the funnel flow hopper to avoid flow problems due to a rathole. The flow pattern in which a bulk solid discharges from a storage system strongly influences the flow problems that may occur in that facility.

Jan 1, 2009

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By Bagley A. S

The accuracy and precision of rutile analyses are discussed. Comparison is made between the wet chemical and X-ray fluorescence spectrographic methods of. estimating Ti02 in commercial rutile. Various allotropes of 'I'i02 are identified by diffractometry and a comparative analysis of the coloured varieties of rutile is given. For X-ray fiuorescence . analysis, specimen preparation is critical and sample grinding and pressures. for pellet making are discussed in detail.Cellulose bonded and backed pellets are shown to be subject to relaxation with increasing age.INTRODUCTIONTo date much of the analytical work on commercial samples has been done by wet chemical methods.This led to various discrepancies in results, which are of particular importance when certificates must be issued for overseas shipments. The present work reviews the nature of rutile and compares the results of Ti02 estimation by wet chemical methods and those obtained by X-ray fluorescence spectrographic analysis.In the rutile industry the results from different analysts and even those from the same analyst are not always consistent. To the analytical chemist this should not be surprising.Fairbairn (1951) showed the results obtained from 34 different analysts on a specially prepared sample of granitic rock. It is of some interest to note that the Ti02 content as determined by the 34 analysts using unspecified methods ranged from 0-17 per cent to 0·30 per cent. Fairbairn (1953) found that1. replicate analyses from the same analyst give a high order of precision,2. analyses by different analysts using the same procedures give reasonable precision, and...

Jan 1, 1965

Application of Discrete Element Method for Simulating Feeding Conditions and Size Reduction in Cone Crushers

Sep 13, 2010

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By Nilufer Kursunoglu

Despite being crucial for meeting the world’s energy demands, coal mining operations present considerable health risks, especially when it comes to exposure to coal dust. Longwall coal mining, an advanced technique, has considerably enhanced production but made dust control more difficult. Due to its explosive nature, coal dust continues to be a serious and dangerous concern in the industry despite developments in safety technology. This study aims to comprehensively assess the risk of coal dust explosions by integrating fuzzy risk matrix and Pareto analysis methodologies, offering precise risk ratings for various root causes. A fuzzy risk matrix was developed to assign exact risk ratings to identified root causes. Additionally, a Pareto chart was used to identify the main reasons and suggest particular preventive measures. 17 significant causes were determined for underground coal mines based on the study’s methodology, and some preventive measures were suggested. In accordance with fuzzy risk rating values, root causes were divided into six categories. The root hazard with the highest risk rating was identified as ‘accumulation of inflammable gas/gases’. The proposed approach was used to examine incidents caused by coal dust explosions in Turkish coal mines in order to demonstrate the effectiveness of combining the fuzzy risk matrix and Pareto analysis for assessing coal dust explosions. This study gives not only a solid framework for risk assessment but also critical information for classifying the risks associated with coal mine dust explosions. The results highlight the critical necessity for proactive and preventive actions to reduce the hazards of coal dust explosions and protect the safety of mining workers.

Nov 16, 2023