Search Documents

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By G J. Corbett, T M. Leach

Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of youngerPacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995

By E. F. Perry

Simulated weathering tests are used to estimate leachate quality of rocks containing varying concentrations of pyrite and carbonates at mines. This study reports the inter-laboratory results from the third phase of a three part effort to develop a standardized, reproducible simulated weathering test for coal mine overburden. Initial development in phases I and II included evaluation of different test apparatus, effects of particle size, gas composition, leaching frequency and other variables. Phases I and II results are reported by Brady et al (2004) and Hornberger et al (2004). In Phase III, a standard column leaching protocol was used by eight commercial, government and university labs to test five rocks of different lithology, pyrite and carbonate content. Ideally, a simulated weathering test should have three characteristics to be useful in mine drainage studies. These include the capability to produce repeatable results, accuracy in simulating field conditions, and a concise test protocol of weeks to a few months. Simulated weathering, or kinetic testing, produces an effluent that simulates mine drainage composition. This can be beneficial for predicting mine drainage quality in comparison to whole rock analyses. The effluent may be tested for the same water quality parameters as the drainage produced during mining, such as pH, acidity, alkalinity, sulfate, iron, manganese, aluminum or other parameters. If the physical, chemical, and biological conditions of the kinetic tests are representative of those found in the mine environment, leachate composition may be used to estimate the water quality parameter concentrations produced during mining. Hornberger and Brady (1998), and Geidel et al (2000), compiled comprehensive chapters on kinetic tests for mine drainage prediction. These sources included: (1) a chronology and synopsis of scientific literature on these kinetic tests as they have developed over approximately 50 years, (2) discussion of the influence of physical, chemical, and biological processes, and (3) general guidelines for test procedures, data interpretation, and recommendations for further research to develop standard methods. Most of the kinetic test methods in use today were substantially developed and applied more than 40 or 50 years ago, including leaching columns (Braley, 1949), humidity cells (Hanna and Brant, 1962), Soxhlet reactors (Pedro, 1961), and field scale tests (Glover and Kenyon, 1962). . The most commonly used kinetic tests for mine drainage prediction are leaching columns and humidity cells. While these kinetic test methods and others have been used in hundreds of mine drainage studies as shown in Hornberger and Brady (1998) and other references (e.g. Sorini, 1997), they have rarely been used in coal mine permitting by either regulatory agencies or the mining industry. The major impediment to routine use of kinetic test methods is the variation in the design and operation of these kinetic tests, and lack of a standardized, accepted (e.g. by EPA or ASTM) test method. Interpretation and data comparison from different studies can be difficult. METHODS Five rocks of varying lithology, mineralogy, carbonate and pyrite content were collected in bulk from Pennsylvanian age coal measures in Pennsylvania, West Virginia and Indiana. Mineralogical composition of the samples was characterized in detail by Hammerstrom et al (in press) using optical, X-ray diffraction, scanning electron microscopy and electron microprobe methods. Acid Base Accounting (Sobek et al 1978; Skousen et al, 1997, Kania, 1998) was performed on bulk samples for % total sulfur (%S) as a measure of pyrite and potential acid generation, and Neutralization Potential (NP) as an index of carbonate content. A modified NP test, following the procedure suggested by Skousen et al, 1997 was also conducted for four of the five samples. The modified NP test accounts for initial acid consumption, Fe oxidation, and subsequent Fe hydrolysis by the iron carbonate mineral siderite. Siderite, even though it is a carbonate gives zero net alkalinity. Lithologic, Acid Base Accounting and general mineral composition data for the five rocks are shown in table 1 (see Appendix). Whole rock elemental analysis for major and trace elements was conducted on a sub-sample of each rock type. One laboratory was contracted to mix, homogenize, and size the bulk samples and prepare sub-samples for all the participating labs. Splits were sent to eight labs, and each organization was provided a detailed set of instructions for column assembly and leaching procedure. The protocol was developed based on results from phases 1and 2 of this study. The principal features of the column assembly are: a specific composition of particle size by weight (table 2), weekly leaching cycles, and incubation under humidified air containing 10% CO2. Figure 1 shows the column construction. [ ] The particle size distribution of the crushed rock sample is largely an artifact of the crushing process, rather than a natural systems process like the particle size distribution of a soil or an unconsolidated sedimentary deposit. The standardized particle size distribution, shown in Table 2, promotes operational consistency of the weathering test procedure, and provides better control over reaction kinetics. Large amounts of fine particles within specific zones of the leaching columns have been found to impede uniform fluid flow and/or gas flow (Hornberger and Brady, 1998). Regarding reaction kinetics, the importance of surface area to volume ratios has been described in a previous phase of this study (Brady et al., 2004), and significant differences in crushed particle size distributions and effective surface areas were found among the lithologic units. Standardizing the particle

Jan 1, 2009

By Thorndycraftm R. B.

"PURPOSEThe purpose of this presentation to the Canadian Mineral Processors is to review gold heap leaching systems currently in use and discuss their applicability to Canadian ores. The author's experience with the development and operation of heap leaching spans the past four years at. Pinson, and visits to many ether heap leaches in the western United States.INTRODUCTIONBy way of introduction to the heap leaching system, I will describe in slight detail the method used at Pinson Mining in northern Nevada. This will be followed by a discussion of optional methods in use at other operations visited.The Pinson orebody is a finely disseminated, well-oxidized hydrothermal deposit. Gold particles are finer than 20- microns. The orezone hostrocks are metamorphosed and silici¬fied limestone and shale. Sulfides and carbonaceous materials are negligible.The Pinson open-pit mine has operated since June 1980. It produces 1500 tpd of C.I.P. mill feed averaging .10 oz gold per ton, and 1500 tpd of heap leach material averaging .025 oz gold per ton. Cutoff grades are 0.04 for mill feed, and 0.01 for heap leaching. Stripping ratio is 9 tons of waste and leach grade to 1 ton of mill feed.The project is located in northern Nevada at 4900 feet above sea level.,Winters are fairly severe, with freezing conditions affecting operations from early December through April. Although officially designated as ""high-mountain desert"" country, snow and/or freezing rain occur almost every week of the winter.To date, all Pinson production-scale heap leaching has treated run-90,000 tons of ore are stacked on 300 foot square clay leach pads. Cyanide leach solution is applied through ""wobbler"" sprinklers at .0025 gpm/sq ft for 60 to 90 days. The pregnant solution flows from the heap by gravity to plastic-lined ditches, into a collection sump and then through buried piping to the 2.2 million gallon pregnant solution pond."

Jan 1, 1984

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O'Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

Jan 1, 1967

By Rimas Pakalnis

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten(10) mines throughout North America. It outlines areas of concern in terms of design requirements.

Apr 1, 2005

By F. T. Cawood

This paper focuses on the role of the coal mine surveyor at the start of the 21st century. It demonstrates that surveyors must look beyond their legal appointment and pursue opportunities to add value at an operational or corporate level of the company. It also exposes the shortfall of statutory appointments in defining the surveyor?s role in terms of key business drivers of the company. One such an opportunity is the potential role of the surveyor in mineral accounting and quality assurance to meet mine requirements, market specifications and standards pertaining to corporate governance and reporting. Finally, some thoughts are expressed on what can be done to elevate current practice to best practice and how to achieve this goal

Jan 1, 2007

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By Wade A. Narin, James K. Mitchell

Hydroblasting is considered a distinct soil improvement technique from explosive compaction, though the blast designs for the two techniques are similar. Hydroblasting is a three step process developed for densifying unsaturated, collapsible soils, especially loess. The required steps are: prewetting the soil to an adequate saturation, placing and detonating the explosive charges, and consolidating the soil (squeezing the water out of the pore spaces between the soil particles under gravity) to a denser state.

Jan 1, 1995

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By S. E. Olsen, K. Tang

Slag-metal and slag-metal-gas heterogeneous equilibria involving MnO-containing slags have been simulated using recently developed Mn-based alloy and IRSID oxide thermochemical databases. A large number of experimental equilibrium data have been used to verify the calculation results. The experimental slag-metal and slag-metal-gas equilibria in MnO-SiO2binary, MnO-SiO2-CaO and MnO-SiO2-Al2O3ternary, MnO-SiO2-CaO-Al2O3quaternary andMnO-SiO2-CaO-Al2O3-MgO higher-order system can be reproduced within experimental uncertainties. The influence of temperature, CO partial pressure and slag chemistry on the Mn-and Si-distribution equilibria have been quantitatively evaluated. This leads to a sound basis for optimizing the manganese ferroalloy production processes. Key words: MnO-containing slag, manganese ferroalloy, equilibrium simulation, thermochemical database

Jan 1, 2004

By D. S. Richards

Computers have revolutionized the collection of data on modern mines. Never before has it been possible to collect data from all aspects of the mining value chain at rates now common. With this has come a new challenge. Deriving information from these copious amounts of data and disseminating it. This problem is being exacerbated by technical software systems, which use proprietary and binary data formats that severely inhibit the flow of data and information both across departments and the larger organization. Generally this had led to data duplication and data redundancy. The Gemcom Enterprise Mining System (GEMS) makes use of industry standard, secure and open databases for all its data objects. It manages multiple users accessing the same bits and bytes in the database, preventing data duplication and redundancy. Developed in the Microsoft BackOffice ® environment, GEMS is also able to leverage the enormous amount of tools available in this environment, whether it’s for e-mail notification, reporting or data capture. Microsoft’s® Active Server Pages are one of these tools. These are standards used to create dynamic and interactive web pages with links into databases and many other objects. The real example outlined in the text, demonstrates how a user anywhere in the world is able to login to a web page and run a query that returns a report with vector plots of performance for the user-selected time frame. As integration is tightened between the various components of the mining value chain, the importance and reliance on ASP pages will grow as the need for management information tools develops. Keywords: mines, computers, ASP, GEMS, integration, Microsoft, Management Information.

Jan 1, 2003

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Ertugrul Kaya, Kagan Ozdemir

The results of bench blasting on quarries, have important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc., and the total costs of that mine. Drilling and blasting is an important step in mine producing chain and its results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. Within the scope of this study, the three different hydraulic excavators’ working performances have been studied considering the particle size distribution after bench lasting at a quarry in Istanbul Turkey. Five shots have been realized on the quarry and average particle size of muckpile after each shot were assessed by digital image analysis method. Bucket loading times have been measured by stopwatch study after five shots. Excavator bucket loading times were also estimated by bucket loading time estimation formula which was published in ISEE 2007 Conference, Ozdemir et al. 2007. Estimated and measured times have been statistically analyzed and the accuracy rate of formula has been determined for five events.

Jan 1, 2008

"As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flowsheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particular under threat. The economics of these operations are far more susceptible to metal price, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most cost effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is normally overlooked is how a hydrometallurgical process could also be integrated in the overall flowsheet to achieve higher overall recovery at the mill. In the base metals environment, this is mainly because hydrometallurgical processes are associated with production of metal or use of expensive and toxic precipitating agents once the minerals of interest are solubilised. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams.Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams as well as tailings streams to compliment a concentrator flowsheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middlings concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows plants to operate on a more favourable part grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added on with no process interruptions.Two case studies are examined showing flowsheets and costings to arrive at the value proposition of the GT low grade treatment flowsheet."

Jan 1, 2017