Search Documents

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By J M. Marwan, B Tang

Strain-type rockbursts, or strainbursts, are characterised by a localised violent failure. Their cause is attributed primarily to the sudden release of strain energy, which accumulates in a volume of highly stressed rock as a result of mining activities. Examples of such phenomena are crown/sill pillar bursts created in the mining process, pillar crush in room-and-pillar mining, face ejection in drift development headings at depth, and floor bursts associated with deep shaft sinking. The paper describes a simple method for the assessment of crown pillar bursts in steeply dipping ore deposits which are extracted by the overhand cut-and-fill method. The method is based on a theory previously established by the author to help assess the need for a remedial solution such as pillar destress blasting. Basically, the mining-induced energy storage rate (ESR) in the pillar is compared with the critical strain energy to come up with the so-called burst potential index (BPI).

Jan 1, 2001

By Joseph B. Cummings

"Occurrences of fluorite on the Packard property were first examined by an engineer3/ of the Bureau of Mines in July 1943 as the result of receipt of an application for an access road. In August of the same year the showings were examined by a geologist4/ of the Federal Geological Survey. The property was again examined by an engineer5/ of the Bureau of Mines in March 1944. This last examination resulted in a proposal that access be gained by construction of a truck trail and that the Bureau of Mines undertake to explore the fluorite showings.The truck trail was constructed by the Public Roads Administration, which began the work on February 17, 1945, and completed it 8 days later.The Bureau of Mines exploratory program was completed on May 16, 1945. It consisted of stripping overburden, trenching, test pitting, tunneling, sampling, and topographic mapping.In addition to being described in some detail, the extent of the work as well as results are shown in accompanying tables and figures.Mrs. Rhoda A. Packard, Mrs. Nora 1. Cline, and C. B. Pettingill, all of Tonto Basin, Ariz., own the property, which comprises four contiguous, unpatented lode mining claims recorded at Globe, Ariz., as the Walnut and the Bluebird 2, 3, and 4. The claims are situated in T. 6 N., R. 11 E., Gila County. David L. Roscoe of Tombstone, Ariz., holds a lease and option to purchase.Access to the property is by Highway 88 from Globe, 34 miles to Roosevelt, thence 24 miles by a graded county road along the west side of Roosevelt Lake to Tonto Basin. Here the Greenback Ranch road, constructed by the Forest Service and maintained by the county, crosses Tonto Creek and continues easterly to the foothills. The truck trail leaves the road 8.5 miles east of Tonto Basin and runs 2.5 miles in a southerly direction to the property. (Fig. 1.)The fluorite deposits lie in and along a small canyon in a rough, rocky area at an altitude of about 3,400 feet, Vegetation is scant and of the usual desert variety. The summer climate is dry and hot and the winter climate moderate. Rainfall at the Forest Service Station in Tonto Basin was 11.4 inches from May 1944 through March 1945."

May 1, 1946

By César Alvarado Olivares

El presente trabajo describe la solución planteada al problema de renovar el equipo de celdas de flotación que por el tiempo de uso (19 años) y por su tipo de diseño, ya no ofrecfa el rendimiento que hoy en día se puede conseguir en esta clase de tratamiento. La solución consiste en

Jan 1, 1963

By Frank J. Wiebelt, Spangler Hicker

The Iron Mountain investigations were part of a comprehensive program for making a national inventory of raw materials used in the production of steel. A tentative program of core drilling by the Bureau of Mines was set up for exploration of more promising iron deposits. Iron Mountain was selected as worthy of investigation because it could serve as a potential source of ore for the war-created steel plant at Fontana, Calif. The deposits were reported on by an engineer in October 1943. The purpose of the project was to determine the lateral and vertical extent of ore bodies and to obtain accurate material data on them.

Apr 1, 1948

By B. G. Hunt, E. J. Kwasney, W. P. Campbell, S. L. Gertsman

"AbstractIn the separation of lead and zinc concentrates from the ore from Cominco's Sullivan mine at Kimberley, • B.C., an iron sulphide concentrate is also produced, some of which is roasted to provide sulphuric add for the manufacture of phosphate fertilizer. The iron oxide calcine from the roaster is potentially a valuable raw material for the production of pig iron and steel. To evaluate this material, six tons of .pig iron was produced from it in an experimental 75 k.w. electric furnace at Trail. The pig iron alone, and also in varying proportions with structural steel scrap and commercial pig iron, was used in the production of basic electric furnace steel at the Mines Branch Laboratories, Ottawa. Details are given of the steel making and fabrication procedure, of the visual and microscopic examination, and of the extensive series of tests on the steel produced. The steel produced using Cominco .pig iron in the charge showed normal working properties in all tests carried out.IntroductionTHIS PAPER describes (a) experimental work by The Consolidated Mining and Smelting Company of Canada, Limited ( Cominco), at Trail on the production of pig iron .from Sullivan iron concentrates, and (b) a joint laboratory investigation by Cominco and the Mines Branch, Department of Mines and Technical Surveys, Ottawa, to determine the feasibility of making a satisfactory steel from this pig iron."

Jan 1, 1955

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By S. Utili

"The optimal profile of a rock slope under given geometry constraint is investigated by means of the upper bound method of limit analysis. The optimal condition corresponds to maximizing stability factor. It is assumed that rock failure condition is suitably described by the Hoek-Brown criterion. Genetic algorithm is applied for locating the optimal profile. The optimal profiles turn out to be concave profiles but there are heaps around the toes of the slopes. Compared with plane profiles, the percentage of increase in stability factor can reach up to nearly 50%. The key geometry parameters of the optimal profiles are provided for practical use. The new upper bound formulation is capable of computing the stability factors of slopes of any shape, thus the stability status of a slope under man-made excavation can be monitored during the whole construction period.INTRODUCTIONIn mining industry, man-made slopes are excavated to create working surfaces. It is important to optimize the slope profile in order to maximize slope stability under certain geometry constraint. For instance, when the height and width of an excavation are assigned, a plane profile AC (see in Fig. 1) is widely applied in engineering practice, but it has been proved not the best one in terms of safety (Utili & Nova, 2007; Cala, 2007). A vertical profile ABC is the one with least stability. Thus, it can be deduced that there is a profile within the domain of the rectangle ABCD providing the highest stability. Cala (2007) compared the difference of convex and concave profiles in stability using strength reduction technique. According to Cala (2007), circular concave slopes can increase the maximum slope inclination under given factor of safety. Besides, based on upper bound theory of limit analysis, Utili & Nova (2007) assumed a logarithmic spiral profile to prove it is more stable than a plane profile in terms of the stability factor. Although the above studies attempted to seek the best circular or logarithmic spiral profiles, none of them considered the arbitrary shape of the optimal profile and its contribution to enhance slope stability."

Jan 1, 2015

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By K. R. Griffin

Atmospheric conditions underground are constantly changing and from a safety perspective, it is critical to identify when conditions are trending abnormally. Atmospheric monitoring in underground coal mines allows mine operators to analyze atmospheric conditions underground in real-time. Real-time monitoring can then be used to identify whether atmospheric conditions underground have become problematic. The implementation of a risk assessment and management process allows operators to then use a risk-informed decision making to identify comprehensive site specific ventilation parameters. Establishing risk-informed ventilation parameters and tracking conditions relative to these parameters, management can modify ventilation plans as mine conditions develop to manage evolving risks. Ventilation risk assessment and management allows developing atmospheric monitoring technologies to be fully utilized in order to increase safety standards in the United States. This paper reviews general risk assessment approaches, state of the art ventilation based risk assessment, and the risk assessment and management application within the United States regulatory framework.

Feb 27, 2013

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008

By W. A. Calhoun

Progress made in a second and final metallurgical investigation made by the Bureau of Mines of near-surface Hawaiian bauxitic deposits from Kauai, Maui, and Hawaii Islands, and on a deeper deposit from Kauai, is reported. Previously reported Al2O3 extractions were increased by modifying conventional processes to fit the ore being tested. Increases in Al2O3 extraction were: Kauai, from 82.8 to 95.4 percent; Maui, 85.5 to 94.1 percent; and Hawaii, from 79.5 to 86.4 percent. Use of a "caustic-reduction sinter, leaching, and magnetic separation process" for Al2O3 extraction also produced an iron concentrate of commercial grade, except for titanium content. No successful method was developed for the recovery of a satisfactory titanium concentrate.

Jan 1, 1967

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By Chas. F. Jackson

The work of the Mining Division is divided among seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal-mining section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following, pages the objectives and type of work of each section will be summarized briefly and their active problems listed. The work clone during the fiscal year 1937 will also be summarized.

Jan 1, 1937

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By Xiang-nan Zhu, Hao Zhang, Lin Li, Jun Qiu, Yue-xian Yu, Chun-chen Nie, Xian-jun Lyua

Waste printed circuit boards (WPCBs) are excellent metal resources. Mineralogical characteristics of different components in WPCBs were analysed in this study. Organic-enriched particles, fibreglass-enriched particles, associated particles and metal-enriched particles were obtained by density gradient method. Subsequently, the elemental composition, morphology, dissociation characteristics, functional group composition and phase composition of different components were analysed by X-ray fluorescence spectrometer (XRF), scanning electron microscopy and energy dispersive spectrometer (SEM+EDS), infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). Elemental analysis results show that Cu is mainly contained in metal-enriched particles. SEM+EDS analysis results demonstrate that ideal dissociation can be achieved when the WPCBs are broken to -1 mm. Organic matter particles are enriched with carbon and oxygen elements, while fibreglass particles and associated particles mainly contain Al and Si elements, verified by XRD analysis. FT-IR results show that hydrophilic and hydrophobic groups exist widely in all components, caused by widespread organic matter. This study reveals the important properties of different components in WPCBs, which is of great significance for the subsequent separation process. Key words: Waste printed circuit boards, mineralogical analysis, elemental composition, dissociation; phase analysis, functional group composition

Jan 1, 2020

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006