Search Documents

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By J. R. Thoenen, J. L. Vallely, M. C. Malamphy

"SUMMARYMagnetic and gravimetric surveys wore conducted over an area of ap¬proximately 1,400 square miles in the bauxite district of central Arkansas. The primary purpose of these surveys was to discover any possible buried and hitherto unknown syenite masses favorable for the occurrence of bauxite and to determine the approximate position of the buried flanks of the known syenite masses which might offer conditions favorable for the discovery of new ore bodies.Those surveys indicated that the various syenite outcrops were domes or bosses on a large batholith and that ether similar domes occurred on the batholith but did net outcrop.Drilling on the local geophysical anomalies proved the presence of 10 buried domes, but only 2 of them were found to project above the upper surface of the Midway clays, a requisite of conditions favorable for the occurrence of bauxite ore bodies. The geophysical data indicated the approximate configuration of the buried flanks of the known syenite coutcrops, and the portions of these flanks that project above the Midway have now been outlined more accurately by drilling.The geophysical surveys have produced evidence permitting the elimi¬nation of a large area as unfavorable for the occurrence of bauxite.Magnetic surveys extending along the Midway-Wilcox contact from Gurdon, in Clark County, on the southwest to Searcy, in White County, on the northwest have proved the improbability of the existence of other syenite masses similar to those found in Pulaski and Saline Counties. A detailed magnetic survey of the Magnet Cove area in Hot Spring County has proved that the syenite mass exposed in that locality is an isolated intrusion and entirely unrelated to those of Pulaski and Saline Counties. This syenite mass does not occur under conditions believed to be favorable for the occurrence of bauxite."

Feb 1, 1945

By K Lownie, R Sani, A Sianturi

Part of the PT Freeport Indonesia (PTFI) mine production is in the process of transitioning from the deep ore zone (DOZ) mine to the deep mill level zone (DMLZ) mine. The DMLZ mine is the next lift in the caving series and lies 500&#160;m below the current DOZ footprint.In order to reduce the need for a very expensive additional ventilation system for the DMLZ mine, it was decided to reconfigure some infrastructure and upgrade the performance of the three existing DOZ mixed flow ventilation fans in situ, reducing the new fans required to two. This was far less costly than providing complete new installations.These fans are installed in individual underground chambers in DOZ mine exhaust drifts and connected to the DMLZ mine exhaust drifts system in 7&#160;m&#160;&#215;&#160;7&#160;m airways size, through sets of 6&#160;m diameter by 500&#160;m high raises.The upgrade process involved replacement of motors, fan shafts and bearings. The existing 1600&#160;kW DOZ mixed flow fans are 3500&#160;mm diameter and operate at a speed of 595&#160;rev/min and were originally designed to deliver 390&#160;m3/s at 3.3&#160;kPa. Efficiency optimisation may be required at a later date.The upgraded DMLZ fans are required to deliver 425&#160;m3/s at 3.7&#160;kPa and it was necessary to increase in motor size and speed to 2200&#160;kW at 710&#160;rev/min. This paper will discuss the fan upgrade project and in particular the integration of an unusual ventilation system, which is based on the semi parallel operation of multiple large fans.CITATION:Sani, R, Sianturi, A and Lownie, K, 2017. Operation of deep mill level zone mixed flow fans after the first fan upgrade – a&#160;parallel fans case study, in Proceedings Australian Mine Vent Conference 2017, pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognized and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economic restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist about application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2007

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1&apos;ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By Hamid-Reza Manouchehri

Mining & Sustainability? A Paradox?! ? Production: gradually or exponentially increasing (giant mining) ? Ore Grades: gradually declining, ? Open Cut Mining: now widespread, likely to be sustained in the future though the long-term is hard to predict as new mineral deposits are likely to be deeper ? Waste Rock / Overburden: increasing rapidly, likely to be sustained in the future and closely linked to open cut mining, especially for coal and base metals ? Economic Resources: commonly increasing but some remain stable or gradually declining, future is linked closely to exploration, technology and economics; Increasing population, changing life style and technology development, ultimately result in sustainability in mining industry to hang in the balance and continue.

May 1, 2013

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

Jan 1, 1993

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c&apos; = 30 kPa, F&apos; = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By R. M. Waterstrat

X-ray diffraction and metallographic examination of binary Mn-rich alloys with Ti revealed the presence of intermediate phases in this system. A binary R phase has been identified and also a phase having an a-Mn type structure. The X-ray pattern of the phase TiMn3 is presented and a tentative phase diagram for the Mn-rich portion of this binary system has been constndcted. MANGANESE-rich alloys with titanium have been subjected to thermal analysis at temperatures down to 1100°C by Hellawell and Hume-Rothery.1 Their results indicate the existence of an intermediate phase TiMn3 in this binary system. This phase appears to coexist with the Laves phase TiMn2, and with terminal solid solutions based on the allotropes of manganese, at least down to 1100°C. The above investigators did not attempt to determine the crystal structure of this phase, however. Since, by analogy to the binary systems Mn-V and Mn-Cr3 one might expect to find a phase in this region of the diagram, it seemed desirable to obtain X-ray diffraction patterns of alloys in the concentration range in question, in order to ascertain whether the sigma phase or related structures occur. EXPERIMENTAL PROCEDURES Alloys were prepared by arc-melting electrolytic manganese and iodide titanium in a water-cooled copper crucible under a helium atmosphere. Excess manganese was added to each melt in order to allow for losses incurred during melting. The alloys were then wrapped in molybdenum foil and sealed in evacuated quartz tubes for annealing at various temperatures, as shown in Table I, followed by quenching in cold water. Although the inside of the tubes showed evidence for some loss of manganese from the specimen during annealing, there was no evidence of any reaction between the specimen and either the molybdenum foil or the quartz tube at these temperatures. It was later found that the manganese loss was considerably reduced by annealing these alloys in sealed quartz tubes containing one atmosphere of purified argon. As an added precaution the surface of each specimen was ground off before crushing the alloys to -270 mesh powder, using a hardened steel mortar and pestle. X-ray powder patterns were obtained using either FeKa or CrKa radiation in an asymmetrical focusing camera, which gave excellent dispersion of the closely spaced lines. Pictures were also obtained using a Debye camera of 5-cm radius which provided data in the angular region not covered by the focusing camera. The alloy specimens were polished and examined metallographically, using an etchant consisting of 60 pct glycerine, 20 pct nitric acid, and 20 pct hydrofluoric acid. The 10-g buttons were in each case broken in half and found to be well-melted and free of any gross segregation. One half of certain alloy buttons was submitted to chemical analysis in the "as-cast" condition. No appreciable change in composition seemed to occur during annealing . RESULTS The X-ray pattern of alloy Ti1.17Mn0.83 was found to agree well with that of the ternary R phase which was first found in the Mo-Cr-Co system,&apos; and re-

Jan 1, 1962

By J. A. Luckmann

"SynopsisThe purpose of this paper is to introduce an innovative approach to risk management in surface mining operations, namely, positive risk. Traditionally, risk management focused on mitigating losses (negative). Positive risk, on the contrary, reverses the approach and focuses on exploiting a project’s inherent benefits (positive).The inability to accurately determine project objectives during the project planning phase and the failure to achieve those objectives during the execution phase is a major problem for any project management in the mining environment.The advance of computer aided design models for mine planning enables mining engineers to examine various options within a very short time. Employing positive risk management combined with drivers-based risk management when evaluating these options provides an ideal opportunity to investigate areas for improving the mining project’s profits. Furthermore, harnessing positive risk returns during the planning phase contributes immensely to the successful achievement of project objectives.Mining has inherent business risks, which can appear overwhelming when considering the risks associated with a mining project schedule, cost, and safety or resources, etc. The question is – how to manage risks in a surface mining environment, and what process methodologies, work methods, processes, and standards should be used when considering the surface mining risks. Applying the principles of positive risk management to manage surface mining risks is not only relevant, but definitely beneficial to mining projects and to the mining industry as a whole.It would be beneficial for risk managers and risk professionals to understand the roles of positive risk ‘drivers’, also known as ‘propitious attractors’. Identifying, analysing, estimating, and understanding the propitious attractors, their behaviour and their influence on project risk events helps considerably during the planning and execution phases. The theoretical and practical knowledge of both sides of the risk – the downside risk (negative risk) and upside risk (positive risk) – can add substantial value to any organization when downside risk is adequately mitigated and upside risk is beneficially exploited."

Jan 1, 2015

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

Since the last occasion on which I spoke to you on this subject there has been a considerable increase in the mechanical ventilation of Western Australian mines.The following table compares the figures for 1939 with those of 1941. The type of fan most commonly used is the limit load fan. On account of its higher mechanical efficiency it has very largely superseded the multivane fan with forward curved blades.Two fans of the propeller type are in use and these have given very satisfactory service. This type of fan also has a high mechanical efficiency particularly at the correct duty for maximum efficiency.The maximum efficiencies obtainable from the various types are, for &quot;multivane&quot; 670/0, for &quot;limit load&quot; 75%, and&apos; for aerovane 7810/0.References to propeller fans with variable pitch have appeared in the technical press, but no detailed d~scription has been issued. The advantages of these fans for mine ventilation are not obvious. An aeroplane is required to operate over a wide range of duties, while the speed of the motor for maximum efficiency is pl&apos;actically constant. In such circumstances the propeller can be adapted to the particular work it has to do by varying the pitch of the blades. In a mine the speed of the fan can be varied to suit.the conditions, and it would appear that variable pitch is not necessary while there is a reasonable range of fans to choose from.The question of the correct position for the fan still comes in for considerable discussion. Exhausting fans at the surface have the support of time and custom, and in many cases this represents the only reasonable arrangement. Such fans should be fitted with an evase, especially in the case of fans with a high outlet velocity such as the aerovane types.It is claimed that there are advantages in having the fan at the surface where it is readily available for inspection and maintenance. Experience has shown that these advantages are more apparent than real. Fans will run for long periods with no attention other than occasional greasing and cleaning, and modern electric motors will run without attention for very long periods.In some instances the expense of a power cable to take current to the fan may be saved by placing it on the surface, but in the majority of cases...

Jan 1, 1941

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF &apos;THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By Hongsheng He, Xiaofang Lv, Jianfeng Wang

This paper provided an overview of characteristics of limonite ores as well as their influence on sintering performance. Evaluation experiments focusing on basic characteristics, granulation characteristics, and high temperature sintering characteristics had been conducted by using two types of limonite ores, then the principles of high effective utilization technology of limonite ores were discussed, and the sintering pot tests were conducted. Limonite ores possessed low total iron content, high combined water content, high SiO2 content, large average particle size, low adhering particles proportion, high porosity, high water absorption rate, short water absorbing time, poor granulation ability, high melt formation ability, low melt fluidity ability, low melt penetration ability, high melt absorption ability, low bonding phase strength, and high forming ability of SFCA. By taking the technical measures of ore-proportioning optimization, increasing the proportion of burntlime and segmentation granulation, the usage of limonite ores could reach 50% in sintering.

Aug 27, 2021