Search Documents

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and l200°C, positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation where negative deviations were observed.

Jan 1, 2003

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V,Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By I. Campbell, P. C. Jones, E. G. Potter, R. P. Taylor

"The Cobalt embayment is a large domain of Paleoproterozoic clastic sedimentary rocks that unconformably overlies the Archean Abitibi greenstone belt. Regionally extensive sills and dikes of Nipissing diabase, emplaced circa 2219 Ma, occur throughout the embayment and are the preferential host to gold-bearing polymetallic vein systems on the Merico-Ethel property, near the northeastern margin of the Cobalt embayment. These gold-bearing, polymetallic veins are predominantly east-west-trending, steeply dipping, discordant calcite- quartz vein systems that formed close to the time of crystallization (within ~15 m.y., based on Pb-Pb ages) of the Nipissing diabase. The ore mineralogy is complex in character, typically comprising sulfides, arsenides, native metals (gold and silver), and specular hematite, preferentially concentrated along the interface between silicate and calcite gangue. A simplified sequence of mineral deposition in the veins is: (1) "Early-stage" pyrite ± chalcopyrite hosted in quartz ± chlorite gangue; (2) "Main-stage" polymetallic (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U) sulfides, arsenides, and native metals hosted in calcite gangue; and (3) "Late-stage" calcite flooding ± galena. Wall-rock alteration in Nipissing diabase is restricted to narrow (<5 cm) haloes of calcite-chloriteepidote- bearing assemblages, whereas a weak alteration halo of specular hematite, calcite, and allanite-epidote has been observed in the surrounding sedimentary rocks. In terms of their age, geology, mineralogy, paragenesis, and morphology, the gold-bearing vein systems at Merico-Ethel closely resemble the silver-sulfarsenide vein deposits of the historic Cobalt and Gowganda mining camps. These observations indicate that the Au-bearing veins are variants of the Ag-vein systems and as such, have a common genesis belt. L’Échancrure de Cobalt est un large domaine de roches sédimentaires clastiques d’âge Paléoprotérozoïque qui reposent en discordance sur la ceinture de roches vertes d’Abitibi d’âge Archéen. La Diabase de Nipissing, mise en place vers 2219 Ma et qui constitue un réseau de sills et de dykes d’importance régionale, est présente dans l’ensemble de l’échancrure et constitue la roche-hôte principale des systèmes de veines aurifères-polymétalliques de la propriété Merico-Ethel, près de la bordure nord-est de l’Échancrure de Cobalt. Ces veines à minéralisation aurifère et polymétallique constituent un système de veines de calcite-quartz sécantes d’orientation principalement est-ouest et à pendage fort qui se sont formées peu de temps après la cristallisation de la Diabase de Nipissing (à ~15 Ma près, d’après les âges Pb-Pb). La minéralogie de la minéralisation est complexe; elle consiste typiquement en sulfures, en arséniures, en métaux natifs (or et argent) et en hématite spéculaire, préférentiellement concentrés à l’interface entre les silicates et la gangue de calcite. La séquence de déposition simplifiée des minéraux dans les veines est : (1) «Stade précoce» pyrite ± chalcopyrite encaissés dans une gangue de quartz ± chlorite; (2) "Stade principal" sulfures polymétalliques (Cu + Co + As + Ag + Au + Bi ± Pb ± Ni ± U), arséniures, et métaux natifs dans une gangue de calcite; et (3) "Stade tardif" calcite massive ± galène. L’altération pénétrative de la Diabase de Nipissing est confinée à des halos étroits (<5 cm) présentant des assemblages marquées par la présence de calcite-chlorite-épidote, tandis qu’un faible halo d’altération en hématite spéculaire, calcite et en allanite-épidote est noté dans les roches sédimentaires environnantes. De par leur âge, leur géologie, leur minéralogie leur paragenèse et leur morphologie, les systèmes de veines aurifères de Merico-Ethel ressemblent beaucoup aux gîtes filoniens d’argent-sulfoarséniures des camps miniers historiques de Cobalt et de Gowganda. Ces observations indiquent que ces veines aurifères constituent une variante des systèmes des veines argentifères et qu’elles partagent"

Jan 1, 2009

By David Bendersky

The principal objectives of this study are to: (1) survey electrical practices in metal and non-metal mines, (2) survey electrical practices in metal and non-metal mills, (3) clarify the federal regulations governing electrical practices in metal and non-metal mines/mills, (4) analyze electrical accidents, and (5) make recommendations aimed at improvement of the safety of electrical practices in metal and non-metal mines. Information was obtained from literature searches, accident reports, visits to 27 mines and 12 mills, and discussions with knowledgeable industry and government people. The various electrical power systems and practices at the mines and mills visited are described. Similarities and differences based on the type of mining and the minerals being mined or milled are presented. The federal regulations governing metal/non-metal mine/mill electrical practices (Code of Federal Regulations, Title 30, Sections 55.12, 56.12, and 57.12) are presented and discussed. Explanations of each regulation are provided in an appendix. The attitudes of mine/mill operators towards the federal regulations are described. An analysis of the electrical accidents in metal/non-metal mines and mills during the period 1972-1978 is presented. Recommendations, including specific research and development activities, aimed at improvement of electrical safety in metal/non-metal mines are submitted.

Jan 1, 1980

By D. Harrington

A uniform hoisting-signal code for mines hoisting from more than one level, if adopted by all mining States, would be beneficial to employees and owners alike and should largely reduce the number of hoisting accidents. Misunderstood hoisting signals cause many shaft accidents involving injuries to men, damage to equipment, and loss of production from the resultant delay. Many of the metal-mining States have adopted codes for hoisting that are effective within the borders of that State but usually entirely different from the signal code, if any, in use in an adjoining State. For many years safety engineers have recognized this lack of uniformity as a distinct hazard, but a uniform code has never been adopted by the States or by the mining industry in those States that have not incorporated signal codes in their mining laws or mining regulations.

Jan 1, 1944

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By Jo Katembo, Patty Bwando, Patient K. Ilunga, Yves Kalubi, Emman Mulaj

"From 2010, the dolomite concentration in the ore fed to the Usoke Plant increased, resulting in a significant increase in the gangue acid consumption and Mg build-up in the circuit, and thus an increase in the Mg:Co ratio in the plant solutions. This affected the Co salt grade, reagent consumption, filtration and drying capacity. Efforts were put in place to minimise the acid consumption and consequently the Mg dissolution (such as use of pre-diluted acid), but the benefits were negligible. Various efforts were then initiated by CHEMAF to improve the cobalt plant productivity (quantity and quality) by process changes, dual precipitation and seed recycle. The positive results obtained in the laboratory were successfully implemented on plant scale. A change in the process from a single-stage precipitation with Na2CO3 to dual precipitation using a combination of Na2CO3 and NaOH improved the capacity of the Co salt filtration by 30%, the Co salt grade and drying capacity by 50%, and reduced the reagent consumption by 22%. Implementation of precipitate seed recycle increased Mg rejection by 40%, improving the Co salt grade from 20% to 25%, and yielding a further drop in reagent consumption. INTRODUCTION CHEMAF (Chemicals of Africa), a mining company located in Katanga province of Democratic Republic of Congo (DRC), has been operating since 2003. The Usoke hydrometallurgical plant treats the Cu-Co ore from the Etoile pit to produce Cu cathodes via a leach–solvent-extraction (SX)–electrowinning (EW) circuit and Co salt via a selective precipitation process. The plant was designed to treat run-of-mine (ROM) ore grading 6% Cu and 1.5% Co; but, in 2008, due to a decline in grades, a heavy-media separation (HMS) plant was commissioned to enrich the low-grade ROM (3.5% Cu and 0.5% Co) up to 8% Cu and 1% Co before feeding it to the hydrometallurgical plant. Co is recovered by precipitation of Fe and Al with limestone, followed by Co precipitation as Co carbonate using sodium carbonate (Na2CO3), also known as soda ash. 85% of the final effluent from cobalt precipitation is recycled back to the plant as process water; the balance, 15%, is bled out and compensated for by fresh water top up to control and retard the rate of sodium sulfate build up."

Jan 1, 2015

By John G. Henning

The Hoyle Pond underground mine is located in the Porcupine Gold Camp, 18 km east of downtown Timmins. Since the initiation of production in 1985, the operation has produced in excess of 1.9 million ounces of gold at a grade of 15 grams per tonne. Currently, Hoyle Pond ranks 8th in total ounce production for all past and present producing mines in the camp, with the highest head grade of any of the significant past, or present producing mines in Timmins. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. Using illustrative examples, this paper provides an overview of factors, such as geologic setting, rock mechanics challenges and mine infrastructure, which influence mine design at Hoyle Pond.

Oct 1, 2004

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

llmenite from the west coast of the South Island, New Zealand, shows exceptional reactivity with dilute sulphuric acid. Based on this, a cyclic acid leaching process was developed for the production of material with more than 98% TiO2, suitable as a substitute for mineral rutile.Titanium hydrate is recovered from the leach liquor by hydrolysis, and is calcined to give the required product.Ferrous sulphate is crystallized from the hydrolysis filtrates, which after concentration are returned to the leaching stage. The need for further evaluation of the process on a larger scale is indicated.

Jan 1, 1973

By L. R. Raymond

With the trend toward deeper and consequently hotter holes, measurements of drilling mud properties at atmospheric temperatures are becoming increasingly inadequate.&apos; Both the prediction and control of down-hole mud properties depend in part upon our knowledge of temperatures in the wellbore. Consequently, a better understanding of factors that affect temperatures during circulation and trips could improve drilling operations. It was toward the goal of obtaining this understanding that this study was directed. Other investigators2 have studied the response of fluid temperature in the borehole during trips. However, all of these studies have used an assumed formation temperature profile at the conclusion of circulation and have provided no means to calculate this profile directly. In this study, the formation profile during circulation was calculated. Other investiga-tors3-5 have also studied bottom-hole temperature during circulation. However, they have developed neither general techniques for calculating the entire temperature profile in the system nor generalized methods for predicting bottom-hole fluid temperatures during circulation. Such techniques and methods have been developed and are discussed briefly in the following pages. Temperature Behavior During Circulation Circulation of fluid during the drilling operation is represented schematically in Fig. 1. The process of circulation has three distinct phases: (1) fluid enters the drill pipe at the surface and passes down the drill pipe; (2) fluid exits the drill pipe through the bit and enters the annulus at the bottom; and (3) fluid passes up the annulus and exits the annulus at the surface. To simulate the thermal behavior of the fluid in the system, each of the phases of circulation must be described mathematically. In Phase 1, the fluid enters the drill pipe at a specified temperature, TDo. As the fluid passes down the pipe, its temperature is determined by the rate of heat convection down the drill pipe, the rate of heat exchange between the drill pipe and the annulus, and time. Phase 2 of the circulating process merely requires that the fluid temperature at the exit of the drill pipe be the same as the fluid temperature at the entrance of the annulus; i.e., TD(L,t) = TA(L,l). Thus in Phase 3, the fluid enters the annulus at TD(L, t). As the fluid flows up the annulus, its temperature is determined by the rate of heat convection up the annulus, the rate of heat exchange between the annulus and the drill pipe, the rate of heat exchange between the formation adjacent to the annulus and the fluid in the annulus, and time. These rates of heat exchange and the time dependency of mud temperature are described by well known heat-flow equation.6 Consequently, as shown in the Appendix, the temperature profiles in the drill pipe, annulus, and formation can be obtained by solving Eqs. 1 through

Jan 1, 1970

By Adriaan de Villiers

Many conventional structural analysis and design methods in current use are not appropriate for the mining industry. Two major reasons for this are that: • The economic life of a particular mine is limited, and • Much of the equipment and machinery used by the mining industry operates at relatively low speeds. Both of these factors can have significant cost implications if they are not properly accounted for during plant design. In particular, the often used practice of mitigating excessive vibration by adding mass to machinery supports is not only expensive but may worsen the vibration effects. Some of these problems, such as increased wear and tear, are not always easy to trace back to inappropriate design. This article focuses on vibration related issues and demonstrates that the mining sector has unique problems requiring unique solutions. Vibration: the basics Historic developments leading to current vibration design practices provide the key to why such practices are often inappropriate for the mining industry. To understand this, it is necessary to introduce some basic vibration theory. Consider a simply supported beam or foundation on which a vibrating machine is mounted. For analysis of the system&apos;s dynamic response, it may be viewed as a mass attached to a spring and a damper, such as the shock absorber of a car.

Jan 1, 1992

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By Mike Johnson, Niels Verbaan, David Dreisinger

The Search Minerals Foxtrot project in Labrador represents a significant Canadian resource of rare earth elements rich in the sought after heavy rare earth elements (19.8% HREE/TREE). A preliminary economic assessment of the project indicated that the project is technically feasible and economically attractive. A variety of metallurgical test programs have been undertaken which have led to significant streamlining and simplification of the process flowsheet. The improved flowsheet should allow Search to reach production earlier and will use conventional processing equipment. The results of these test programs are presented and discussed in this paper.

Jan 1, 2014

By G. S. Pauley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Case-based reasoning can be a catalyst for improvement). A new computer software technology known as Case Based Reasoning (CBR) can be used to produce small decision support systems that are economically viable. This is because the knowledge that they contain can be owned and maintained by their users. A CBR tool has been used to perform a pilot study with Anglesey Aluminium Metal Ltd. The results are encouraging. They suggest that a combination of CBR and participative design and implementation techniques (such as Checkland's Soft System Methodology) can achieve sustainable improvement in mineral processing functions. An explanation is presented of why traditional, rule based systems are often an ineffective way to implement support systems. It is shown that CBR may provide an appropriate technology solution. Methods of achieving sustainable benefit are indicated. The pilot study with Anglesey Aluminium Metal is used as a practical illustration of the development of a CBR application. A review of potential application areas and some observations about the implementation are presented

Apr 1, 1994

By Dezhou Wei, Cong Han, Shuling Gao, Wengang Liu, Yanbai Shen

The recycling schemes of copper mineral to a copper raw ore produced in China is investigated in this paper, of which is aimed at copper concentrate‘s grade is over 26.00% and recovery is over 90.00%. The primary copper mineral the raw ore is chalcopyrite and the main gangue minerals are quartz, orthoclase, albite, clinochlore and phlogopite. There are four useful metal elements contained in the copper raw ore, which are Cu, Pb, Zn, Au and Ag, and the grade of each is 3.75%, 0.01%, 0.11%, 0.31 and 483.5 g/t. Two floating recycling schemes and its corresponding flotation reagent system were determined. The results show that calcium oxide, sodium carbonate and sodium sulphide were used as regulators, sodium n-butylxanthate was used as collector and terpenic oil was used as frother in two floating recycling schemes are effective. The open-circuit test’s results show that the copper mineral contained in raw ore can be effective collected, and both concentrates gotten through two schemes are up to grade.

Jan 1, 2014

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014

Fine coal is defined as material with a maximum size of 1/2 in. Various methods for separate washing of such coal are discussed briefly because separate treatment can lead to a higher overall recovery of coal or to a product having a lower ash content.A felspar jig is discussed in detail because it is the method most recently adopted in Australia, and because it has the advantages of compactness, flexibility and automatic Gontrol, with minimum operator attention. This jig has a variety of adjustable controls to enable the desired results to be obtained from a wide range of coals and the general application of each control is discussed.The only separate treatment of fine coal in the Illawarra district is by felspar jigs on Bulli seam coal.INTRODUCTIONAll reasonably large Australian collieries now win coal by mechanical methods. but while mechanization leads to more economic production of high tonnages, it also changes the characteristics of the coal won. In particular there is an increased proportion of fines, and an increased ash and moisture content. However, specifications of coal for sale have become more stringent, and consumers now require coals in a definite size range with a lower and more uniform ash content, as well as with a low and uniform moisturecontent.These factors have led to the need to wash and grade run-of-mine coal at the pithead. In&apos; plants where the whole of the run-of-mine coal is treated in a jig, some of the fine coal in the feed is beneficiated; the extent depending on factors such as the type of coal and the feed rate. However, for dense medium treatment, fine coal must first be screened out, and there may then be no washing of fine coal at all.

Jan 1, 1961

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996