Search Documents

Coal mining in New Zealand is principally a State-owned and controlled operation where the State produces 70 per cent of the coal in New Zealand and 65 per cent of coal mined in the Waikato. The State's flexibility in production quality and price makes them tough competition. Coal in the Waikato varies in quality considerably throughout the region making the high quality coal deposits as in the Huntly district a highly sought after commodity. The high quality of coal is often offset against transport costs as, for example, Maramarua coals can compete effectively in the Auckland market and dollar per calorific value basis.

Jan 1, 1984

By I. A. Kunasz

This paper is not intended to review and re-state general information on lithium, but rather to analyze the paradigm that has caused such a rapid rise in lithium production and the development of new lithium producing centers. Details on pegmatites, brines, concentrate and chemicals are amply covered in a number of publications ? SME?s Industrial Minerals and Rocks, Industrial Minerals, Roskill and a host of other publications. There is no question that the latest interest in lithium has been driven by the potential development of the electric car. This stimulus prompts one to recall two symposia: 1. ?Lithium Resources and Requirements be the year 2000?, organized in 1976 by the U.S.G.S. in Denver (1) and the sequel 2. ?Lithium ? Needs and Resources? at Corning, N.Y. (2).

Jan 1, 2011

By Higgins RJ

Environmental investigations have been undertaken by Ok Tedi Mining Limited (OTML) since 1981 when the Ok Tedi Environmental Study was commenced. Environmental monit- oring and management programmes were implemented in 1983. The programmes included water quality monitoring, river flow and sediment monitoring, surveillance of aquatic biological communities and a health and nutrition survey of the local people. These original programmes have continued, and additional programmes of work have been developed and revised to reflect changing operations and the need to focus investigations on specific areas and issues of concern. In April 1990, following the establishment by the Government of Papua New Guinea (PNG) of environmental management criteria for the Fly River system, compliance monitoring programs were introduced. Details of the compliance and additional monitoring programmes undertaken by OTML throughout the Ok Tedi and Fly catchments, including programmes of investigation in the Fly River estuary, Gulf of Papua and Torres Strait, are presented.

Jan 1, 1991

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By A. Raja, C. C. Harris

Apparatus for maintaining constant — but adjustable — pulp level and rate of froth removal are described. The results of preliminary experiments into the effect of scraping speed on the rate of solid and liquid recovery with a semi-batch system are presented. Glass spheres restricted to a narrow size range is the solid under investigation. Graphical methods for estimating the mass of recoverable material and the zero error are given. The semi-batch procedure1 is extensively used in laboratory flotation testing, though the method is subject to variability of moderate severity. Raffinot2 concluded from a statistical study of the difference between replicate tests, that the ptincipal source of errot was the test itself and not sampling or chemical analysis. These differences can be ascribed principally to changes in pulp volume and reagent concentration, and uncontrolled rate and depth of scraping. Semi-batch testing has been criticized1 on these grounds as a means of investigating flotation kinetics. This paper discusses and describes modifications to laboratory flotation equipment which reduce the number of manual operations and lead to improved control. Kinetic studies were the primary reason for developing the apparatus described. It should, however be a useful aid in normal flotation testing. Some preliminary results of experiments are presented.

Jan 1, 1967

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By R. F. Hinds

A pressurizing system was designed and built to apply a radial pressure of 5.000 psi to rock samples. Samples of the Bradford, Weir and Kirkwood sandstones were subjected to radial pressures parallel and perpendicular to the bedding in the system and the changes in conductivity, porosity and permeability were deter-mined. Asymptotic decreases in conductivity, porosity and Klinkenberg permeability were observed over the 0- to 3,500-psi range. From these data, the increase of formation factor over the same range was calculated. The cementation exponent expressed in the Archie equation was found to increase with pressu,re. The rate of change varied from formation to formation. Only small differences were observed for samples taken parallel to the bedding as comnared to those taken perpendicular to it except for the Bradford sand. Above 3,500 psi the data are not good enough to tell if the properties continue to fall-off asymptotically or in a different manner. A possible explanation for the probable litnit of the asymptotic rate around 3,500 to 4,500 psi is that this represents the maximum pressure which the formations have unrdergone during their geological life as a result of burial. INTRODUCTION For many years measurements have been made in the laboratory of the properties of oil-bearing sandstones with little consideration being given to whether these properties had been changed when the samples were moved from their original position in the ground to the laboratory. Relatively little has been reported in the literature on the effect of pressure on the properties of sandstones. The changes in permeability for eight typical consolidated oil-bearing sandstone samples with overburden pressure (0- to 15,000-psi range) was presented by Fatt and Davis' in graphical form. In 1953 Fatt' also reported the relationship between porosity and overburden pressure for four typical consolidated oil-bearing sandstone samples (0- to 5,000-psi range). Fatt later described the changes of formation factor and porosity of 20 typical oil-bearing sandstone samples with overburden pressure changes (0- to 5,000-psi range) giving the values of the coefficients and exponents in the Archie' equation, and the more general Winsauer equation', where C, k and m are empirical constants, F is the formation factor, and + is the porosity. During the experiments of this investigation the core was contained in a neoprene rubber sleeve as shown in Fig. 1. It was held between two steel end members which were mounted in a steel cylinder. The unassembled pressure cylinder with its component parts is shown in Fig. 2. The core was insulated from the two steel end members by a Teflon sleeve with a small hole in the

By C. Dinis da Cama

In order to reduce the complexity of mechanisms influencing rock- fragmentation by blasting a simulation approach is proposed, using the capabilities of micro-computer interactive graphics. Situations involving cratering and bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

By J. Nielen van der Merwe

This investigation was done to develop a method to predict the lie of coal pillars. It has long since been known that coal pillars deteriorate over time, but there was no method to quantify the deterioration. It was found that the rate of pillar deterioration was essentially a function of two parameters, namely mining height and time. The higher the mining height, the more rapidly the pillars deteriorated. The rate of deterioration is not constant, but decreases exponentially with time. The pillar life should be viewed in conjunction with the safety factor. While the relationship between safety factor and pillar life is ambiguous, the trend is nonetheless for higher safety factor pillars to have longer lives. The safety factor can be used to quantify a failure probability. The pillar life prediction indicates when the pillars which are predicted to fail, can be expected to do so.

Jan 1, 1998

By Frederick A. Mumpton

Recent findings by medical workers on the association of certain zeolite minerals with the high incidence of pleural mesothelioma in two small Turkish villages have caused considerable excitement both in medical circles and in the synthetic and natural zeolite businesses. The 42 cases diagnosed between 1970 and 1977 in one community of 600 population in a region of altered volcanic tuff represent a virtual epidemic of this rare malignancy which normally strikes only about one person in a million. Cancer workers around the world expect that detailed environmental and epidemiological studies of the disease in these areas will shed considerable light on the cause of this particularly lethal form of lung cancer. Scientists and engineers developing uses for zeolite materials in industry and agriculture, however, are justly concerned that the preliminary results available on this situation will be used by environmental and regulatory organizations to label an entire group of miner- als as carcinogens on the basis of what is little more than circumstantial evidence. Although there is no question as to the large number of cases of mesothelioma in these areas of central Anatolia, the work to date has suffered from a lack of sound geological and mineralogical input. Ataman (1) stated that a "correlation" exists between mesothelioma and zeolites in this region; however, the geological data needed to document a direct relationship between the presence of zeolites in the volcanic tuffs surrounding the villages in question and the rate of malignant lung disease in the inhabitants have g been obtained, nor has evidence that suggests a cause-effect relationship between zeolites and cancer been reported. To provide fundamental information on the distribution of zeolite minerals in areas of central Turkey where high incidences of pleural mesothelioma have been reported and to evaluate from first-hand knowledge the published reports and news releases of medical workers engaged in assessing the problem, the following investigation was made.

Jan 1, 1979

By S. Culp, P. Metcalfe

Web technologies and the Internet have revolutionized the computer industry. The Web browser technologies have also moved to portable devices such as Personal Digital Assistants (PDAs) and mobile phones. This paper looks at how to implement a Web Server solution and addresses some of the inherent advantages in the technology. It will also look at some examples of how plant productivity can be managed with a Web Server approach.

Jan 1, 2002

By Wayne N. Marchant

Introduction The issue of coal mining safety plays an important role in the United States' growing dependence on coal to supply its future needs. This article will address the federal government's role, principally the US Bureau of Mines, in meeting this challenging growth and demand while reducing the social and economic costs attributed to injuries and fatalities in underground mining. Some interesting facts and projections with respect to the nation's energy picture will be discussed. This includes the distribution of its reserves and the projected role of coal in the energy and economics of the nation's future. Underground mining will continue to be an important means of providing this coal. The author will discuss how the Bureau of Mines' research program addresses the problems of health and safety that grow out of the demand for more coal. Future projections First, a synopsis of salient facts and projections concerning the US's situation with respect to energy and the economy. Figure 1 depicts the relative quantities of recoverable energy reserves in the United States by their type. Most people are aware of the nation's use of oil. We hear a lot about natural gas. And we are aware of the controversy over the use of nuclear energy. But, while looking at Fig. 1, the question becomes, "Where will our fuel to meet the demand for energy in the future most certainly have to come from?" With 82% of the nation's recoverable fuel reserves being coal, the answer is irrefutable. Coal will be that source. Figure 2 is the present market for coal. It shows that 77% of the coal mined goes to supply electric utilities. Therefore, the coal industry as a whole is most sensitive to the trends and demands for electricity. It is less affected by what happens in other markets, such as export and direct industrial use. In fact, the coal industry is three times more sensitive to the electric utility market than to all other markets combined. Therefore, the trend in the demand for electricity must be examined. Electricity demand is expected to increase steadily over the next 15 years. It is projected to grow from its present 2.3 trillion kWh per year to 3.5 trillion kWh per year by the year 2000. The fuel to supply this increase in demand must come from somewhere. The question is "How much of this extra fuel will be coal?" Although the demand for electricity is predicted to increase, the demand for coal does not necessarily follow. Coal must maintain its fraction of the energy sources used for electricity generation if its demand is to increase at the same or greater rate as electricity. Except for a near-term dip in demand due to a slight increase in nuclear capacity, the domestic electric generation accruing to coal will go from 56% in 1985 to more than 60% in 2005. Thus, the predicted trend is for coal to become a larger part of the fuel mix for electric power generation. Similarly, looking at the most recent forecast for total coal consumption trends, it can be seen that for electric power generation alone, the coal industry must be able to supply an additional 316 Mt/a (348.5 million stpy) by the year 2000 (Fig. 3). It must be stressed here, though, that without significant improvements in mining safety, it can also be easily predicted that injuries and fatalities will increase in proportion to the increase in coal production. Will society consider that acceptable? This author does not believe so. Figure 4 examines the effect of coal prices on the price of electricity. The projections show that the already high proportion of fuel cost will become a greater fraction of the consumer price for electricity. Specifically in 1985, 36% of the price of electricity was the cost of the fuel. In 1995, 46% of the price of electricity will be the fuel cost. That implies that the price of coal will have an increasing influence on the consumer price for electricity. Thus, as coal is used more to generate electricity and as fuel becomes a greater

Jan 4, 1987

The Archaeozoic Willyama Complex at Broken Hill has suffered several periods of deformation and metamorphism. New structural and petrological information together with that available from the literature gives a picture of the metamorphic evolution of the Barrier Ranges. Several epochs of metamorphism are recognized, and potassium-argon dating of minerals has been applied with limited success to the resolution of these epochs.INTRODUCTIONAdvancements in the mineral industry at Broken Hill over the past eighty years have been accompanied by a continual striving towards increased understanding of both the geological history of the Barrier Ranges and the environment of the Broken Hill ore deposits. However, although many detailed studies of selected localities and particular-aspects of Broken Hill geology have been carried out recently, the regional geology of the Barrier Ranges as a whole has received little attention from a petrological viewpoint since the pioneer investigations of Mawson (1912) and Browne (1922). There still remains a great need for regional surveys combining field studies of the habits, structures and outcrop relationships of the various rock types with laboratory investigations of their chemistry, mineralogy and microscopic ,fabrics. Recording observations arising from three brief visits to the Broken Hill area during 1959 and 1963 may stimulate further surveys.During one of these visits, the generosity of the Zinc Corporation Limited in providing field transport and geological guidance enabled the writer to collect material and study field relationships and appearance of the various rock types at numerous localities covering most of the Willyama outcrop. A complete study has not been conducted...

Jan 1, 1963

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964