Search Documents

By Germán Mallén

Como parte de los estudios línea base realizados por MWH Perú S.A. para el proyecto aurífero Chucapaca de las Canteras del Hallazgo en el distrito de Ichuña de la región Moquegua, Perú, se investigó el origen de boro, alta salinidad y otros componentes que perjudican la aptitud de los ríos Ichuña y Tambo para irrigación y otros usos. En este sentido, se encontró que la calidad de agua es perjudicada principalmente por altas concentraciones de sodio, entre otros, precipitándose como hidróxidos de estos metales debido al pH neutro en el río. En ese sentido, el presente texto describe la relación de este impacto químico con los manantiales entre el Cerro Chucapaca y el cañón del Río Ichuña/ Alto Tambo, ubicados al Norte de Moquegua, donde presentan la característica distribución de diferentes tipos de aguas volcanogénicas sobre un sistema de convección hidrotermal de agua meteórica profunda reciclada, calentada y movida por una cámara magmática andesítica que aporta calor y gases.

Sep 21, 2013

By James E. Aplin

Previous studies have shown that fracturing of roof strata precedes ultimate failure, and that the fracture development causes an accompanying increase in the apparent resistivity of the strata. Using this principal, a microprocessor controlled resistivity roof fall warning system (RRFWS) was developed that automatically sequences through and records up to 32 electrodes that may serve as either voltage or current electrodes. This capability permits increased coverage with a minimal number of required electrodes. The data is stored in a nonvolatile memory and on an optional printout, making the system nonsusceptible to loss of mine-power. To further save battery power, the system's electronics shut down between readings, except for a carbon molybdenum steel real-time clock. At a preprogramed interval, the RRFWS reactivates and repeats the sequence. If the absolute change or the rate of change of resistivity exceeds a predetermined limit the system is capable of sounding an alarm. In addition to the monitor, a stainless steel mod led split-set electrode was also developed that permits long-term corrosion-free contact.

Jan 1, 1983

By Frank E. Chase, John L. Ellenberger, Christopher Mark

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By C. Lumley

The management of the Anglo Platinum (AP) mining technical systems (MTS) embarked upon a process of defining the strategy for the MTS department. The newly established department forms part of the greater Group Information Technology (IT). The strategic process took place within an environment that had witnessed a dramatic proliferation of IT implementations across the group within the last three years. The IT department has been structured in terms of the classical plan, build and run functions with the applications and integration streams running perpendicular across these three functions. The application stream is divided into commercial and mining technical systems with business systems integration the third stream. The mining technical systems department supports mine management to effectively gather, analyse and disseminate data relating to the ore reserve by integrating a number of strategically selected IT applications to ensure that the safety, legal and operational requirements are met. This service to business is rendered by management of a strategic outsource partner via tightly controlled service level agreements (SLAs). The framework used for creating a mining technical systems department that is empowered to add value to business was formulated using the AP value chain as both the starting point and guiding process to ensure alignment to the greater internal strategy of the business. Keywords: Platinum, Mine planning, Mining technical systems, Value chain.

Jan 1, 2003

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

Technical Challenges in the Flotation of Molybdenite from Porphyry Copper Ores

Sep 13, 2010

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

By Víctor Guimaraes

El presente texto señala las estrategias de planteamiento de minado en la minera Tintaya con el objetivo de maximizar el valor neto de la operación minera y a un nivel aceptable de riesgo. Este ciclo de planeamiento, evalúan diferentes alternativas dentro de los siguientes procesos como: optimización del pit (Uso de ley corte durante el proceso, diseño de taludes, Pit descontado, inclusión de nuevos procesos metalúrgicos y de recursos inferidos), generación de fases de minado (Parametrización de fases), programación de la producción (uso de optimizadores basados en programación lineal), planeamiento de desarrollo mina (incluye planes de drenaje subterráneo y superficial), Planeamiento corto plazo y actualización del plan de cierre.

Sep 9, 2007

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By J. Drelich, J. Pletka

Lost foam casting patterns are foamed polystyrene shapes glued together into the shape of the part to be cast and are coated with a refractory material consisting of a mineral mixture and binders. Prior to casting, a significant number of the patterns are damaged and inevitably land-filled. In this study, a process is developed for the recovery of foamed polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and density separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene.

Jan 1, 2001