Search Documents

By Enrique Pasquel Carbajal

El presente texto describe los resultados realizados por el Centro de Investigación tecnológica del Cemento y del Concreto (CIDETEC) sobre el empleo de microalfiler de carbonato de calcio como adición mineral para mejorar las propiedades reológicas en estado fresco y endurecido del shockrete empleado en las labores de sostenimiento en la industria minera. Asimismo, se señalan la aplicación de esta tecnologías en proyectos mineros como Cobriza, Andaychagua, San Cristobal y Pallancata.

Sep 12, 2011

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By Junhwan Lee

Pipe piles can be either closed- or open-ended piles. Pile load capacity for a closed-ended pile consists of the shaft and base resistances, while, for an open-ended pile, it consists of shaft, soil plug, and annulus resistances. In order to investigate the pile load capacity of both closed- and open-ended piles, two field pile load tests were performed. For the open-ended pile, the fully instrumented double-walled system was used to separately measure all the components of the pile load capacity. The soils at the test site were predominantly granular soils with relative densities varying from loose to dense with increasing depth. The incremental filling ratio (IFR), which affects significantly the load capacity of open-ended piles, was also measured during pile driving. The test results indicated that the total load capacity of the closed-ended pile was higher that that of the open-ended pile, mostly due to the difference in shaft capacity. The shaft and base load capacities of the open-ended pile were 44% and 20% lower than the corresponding values for the closed-ended pile.

Jan 1, 2003

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By Russell Griffin

The current state of the art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in under- ground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long- term, in-mine tests are presented.

Platiniferous horizons such as the Merensky Reef that are mined chiefly for their PGE contents constitute one end member of a continuum of Ni-Cu-PGE sulfide deposits; Ni-(Cu) sulfide deposits in which the PGE may or may not be by-products represent the other end of this continuum. Although it has long been thought that PGE-rich sulfides can only be developed by magma mixing in large magma chambers, new PGE data for the Bushveld Complex suggests an alternate model to account for origin of mineralization in the worldÆs most important Pt producer. Briefly, this model suggests that PGE-rich sulfides were initially deposited at depth below the Bushveld Complex as a result of interaction of a S-undersaturated mantle magma with S-rich crustal rocks. These PGE-rich sulfides were subsequently re-dissolved by a second magma, which introduced the PGE into the Bushveld Complex magma chamber, where the PGE-rich reefs were formed due to cooling of these magmas. If this model is correct, it means that large layered mafic/ultramafic intrusions are not a prerequisite for the formation of economic PGE-rich deposits. Exploration for Merensky Reef-type PGE deposits can be greatly facilitated by documenting variations in the background PGE contents of non-mineralized rocks collected on traverses across mafic/ultramafic intrusions; the mineralized horizons occur at cross-overs in ratios such as Pd/Cu, Pd/Se and Pd/S.

Jan 1, 2002

By Stephen E. Stewart

This document presents the explosion-proof enclosures used severity of certification tests solutions to linear transient thermal and stress analyses of in underground mines. The results were used to assess the for enclosure windows relative to possible loads occurring in the actual mine environment. Cast iron electric light enclosures with polycarbonate and glass windows were analyzed under steady state thermal conditions (light burning) and for thermal shocks corresponding to an internal explosion (ignition of volatile mine gas) or external quenching (mine water spray system). Thermal shocks to the enclosure, caused by ignited gases or water spray, were applied via a series of load steps in the transient analysis. The temperature dependence of material I properties and of the film heat transfer coefficients were included in the model. The work demonstrates that thermally induced stresses are strongly influenced by the way the window is mounted in the enclosure. It also shows that the MSHA Thermal Shock Test, if performed on an unsupported lens (or window), produces lower stresses than the lens (or window) may experience in the mine environment.

Jan 1, 1984

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

By L. E. Cardwell

This publication contains routine analyses and related source data for 475 natural gas samples from 17 States and two foreign countries. Of this total, 454 samples were collected during calendar year 1971. The remaining 21 samples were collected during previous years, but releases granting permission to publish the analyses were not received until 1971. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Thirteen previous publications have presented the results of 9,427 gas analyses prior to 1971. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1972

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By A C. Carter

The increasing need for alternative energy sources as well as the less clearly perceived but equally increasing demand for non-fuel minerals has resulted in extensive exploitation of near surface deposits. Many such deposits have depleted reserves and mining corporations are increasingly turning their attention to deposits, with thicker overburden, less competent materials, steeper dips and more complex structure. These deposits pose mine layout, geotechnical and equipment problems as well as the need for large outputs to achieve economies of scale. The paper describes the major problems and operational solutions for such deposits using continuous excavation and transport equipment.

Jan 1, 1980

By Joseph Goessling, Mark Kroncke, James Parkes

The I-35 Capital Expressway (CapEx) Central Drainage Tunnels will serve as a stormwater collection system for the forthcoming I-35 Capital Express Central reconstruction project through downtown Austin, Texas. The schematic level concept design included three tunnels, 10 to 14 ft ID, totaling 26,000 LF. Constructability reviews during design development indicated issues with the concept design including phasing of construction, conicts with future retaining walls, staging area concerns, and signicant mixed face tunneling. The design was updated to mitigate these risks. The revised design includes two tunnels, both 22-ft ID and totaling 33,000 LF, that will be mined almost entirely in rock.

Jun 23, 2024

By Ethan Steward, Kyle Perry

To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals.

Feb 1, 2020

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

By R Tweedie

'The politics of mining in New Zealand' is a topic I chose myself because of its importance in the future of the New Zealand mining industry. There are many people in the industry who are cynical about politics, cynical about politicians and definitely cynical and often critical of political decisions. In fact, many industry people say they don't want to get involved in politics, they just want to get on with the business of exploration or mining. The point of my address is that politics is important and the industry cannot afford not to participate in the political process.

Jan 1, 1991

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By J. C. Detweiler

THE Jacksonville plant of Humphreys Gold Corp., operating under leases from National Lead Co. and Rutile Mining Co. of Florida, recovers rutile, ilmenite, zircon, and monazite from an ancient beach deposit containing about 2.5 pct of these minerals in combination. The location of the plant is unique, being situated about ten miles from the center of Jacksonville, Fla., surrounded by a thriving suburb. Two four-lane highways pass within 1 ½ miles of the plant. An expressway now under construction will pass over the tailing pile, within 500 ft of the mine office. The elevation at the plant site is approximately 50 ft above sea level. This is one of two mines producing titanium minerals and zircon in Florida. Another mine is also operated by Humphreys at Starke, about 50 miles southeast of Jacksonville. The Jacksonville deposit extends about six miles in a north-south direction, averaging approximately one half mile wide and twenty ft thick. Values begin at the surface over most of its length and ter-

Jan 1, 1952