Search Documents

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By L. E. Schultze

The Bureau of Mines has devised techniques to recover lithium from geothermal brines as the chloride. More than 99 pct of the lithium was precipitated from a brine containing 170 mg/L Li by adding a solution of AICl3 and increasing the pH to 7.5 with lime slurry. The Li-Al precipitate was dissolved in HCl and sparged with gaseous HCI to recover the AlCl3; this resulted in a solution containing LiCl and CaCI2. The solution was evaporated at 1000 C to obtain a mixture of the chlorides from which 97 pct of the lithium was recovered and 90 pct of the calcium was rejected by leaching with tetrahydrofuran. The LiCl recovered by evaporation of the tetrahydrofuran was purified by dissolution in water and treatment with oxalic acid. The final LiCl solution contained 89 pct of the lithium originally present in the brine and had a purity of 99.9 pet.

Jan 1, 1984

By Phillip R. Moyle

A basic precept in mineral exploration is that the best places to prospect are where minerals have already been found. The California desert has many old mining districts once thought to be "played out" that are currently producing more mineral wealth than at any time in the past. Because no "crystal ball" exists that will enable us to predict the Nation's future mineral needs, land management plans must be flexible enough to respond to these often unforeseen needs. MANAGEMENT ISSUES The California Desert Conservation Area (CDCA) (figure 1) encompasses 25 minion acres, nearly one-quarter of the total area of California. Passage of the Federal Land Policy and Management Act of 1976 (FLPMA) launched an intensive program by the Bureau of Land Management (BLM) to study this vast area. Painstaking scientific investigations were made of wildlife and plant populations, soil, air, and mineral resources, range use, and wilderness characteristics, among other environmental concerns.

Jan 1, 1992

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By A. W. Newberry

The Virginia copper district is situated in North Carolina and Virginia. It contains many mines and prospects that were active at the turn of the nineteenth century. The Bureau of Mines, as part of the strategic-minerals program, began a project in September 1942 to investigate and explore the most promising of the mines in the district. The Seaboard, High Hill, Durgy, and Blue Wing mines were the sites of the main project activity. This report deals principally with these four mines. Drilling did not discover any new ore shoots but indicated the persistence of known ore shoots in depth. There appears to be no indication of impoverishment of copper with depth.

Jan 1, 1948

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951

By Walter R. Storms, Allan B. Bowman

This paper , which describes mining methods and practices at the Mineral Hill copper mine , is one of a series being prepared by the Division of Minerals of the Bureau of Mines on mining methods , practices , and costs in various mining districts. of the United States . The Mineral Hill mine is situated on the northeastern piedmont of the Sierrita Mountains at an altitude of 3,650 feet in sec . 35 , T. 16 S. , R. 12 E. , and sec . 2 , T. 17 S. , R. 12 E. , Pima mining district , Pima County , Ariz . ( fig . 1 ) . The claims (figs . 2 and 3) are in a gently rolling area with only scant desert vegetation . The average annual precipitation is about 11 inches . The nearest surface water is the Santa Cruz River , an intermittent stream 8 miles east of the mine . The property is owned by the Banner Mining Co. , a Nevada corporation . This report presents a brief history of the mine , describes the geology of the area and the ore deposits , outlines methods of prospecting and exploration , and gives methods of sampling and the estimation of ore reserves and values . Development and stoping methods are explained , and methods of underground transportation , ventilation , mine drainage , and safety measures are described . The concluding section of the paper is a section on milling . The Mineral Hill mine is an old mine that was reopened in 1951 after having been closed for 30 years .

May 1, 1957

By Arthur C. McFarlan

There are two distinct coal fields in Kentucky-the Eastern field constituting a part of the Appalachian coal region and the Western field constituting the southern part of the Eastern Interior region. The outcrop pattern of the State is dominated by the Cincinnati arch. Coal-bearing Pennsylvanian strata occupy a low structural position on either flank, preserved thereby from erosion, which in the past has removed these same beds, though a much thinner succession, from the crest of the arch. General geological relationships are shown in figures 1 and 2. On April 13, 1750, Dr. Thomas Walker discovered the first coal recorded in Kentucky. He entered the State through Cumberland Gap (Cave Gap) and found coal a few miles north.

Jan 1, 1944

By Fieldner. A. C.

"In preparing this paper, an attempt was made to obtain results of plant-scale carbonization tests on washed and unwashed coal tram to same mine. A letter. in which the following questions were asked, was sent to some 50 coke-oven superintendents and others who might be interested:“What is the influence of washing coal on:(1) The chemical and physical properties of coke, as for example, the size, the amount of breeze, the fracture, strength, cell-structure, etc.(2) The quantity and quality of gas and by-products.(3) The capacity of the ovens.(4) The composition of the coal..""Your general opinion, as well as any specific data or results of testa, on this important subject will be greatly appreciated.""Of the 45 replies received, 24 stated that they had never used washed coal; 11 had used washed coal but had no comparative data on similar coals washed and unwashed; 7 answered some of the questions based on their general experience; and 3 gave some test data on Pittsburgh bed coal from western Pennsylvania. In none of the three tests did the washed coal come from the same mine as the unwashed. The washed coals in the three tests were from the same washery - one of modern construction in which the operations are under careful technical control in order to give a uniform product containing a minimum of surface moisture. The unwashed coals which were previously used in these plants were from different nearby mines in the same coal bed, and were supplied by the same company. Obviously, no sweeping or finale conclusions can be drawn from these few tests on coal from a single washery. Therefore, the writer vas obliged to consult the literature, coal-carbonization and coal-washing engineers, and other authorities to supplement the fragmentary information gleaned from the questionnaires in order to present a picture of chat gas engineers may expect from the use of washed coal in a carbonizing plant."

May 1, 1930

By V. F. Parry, W. S. Landers

"INTRODUCTION The primary object of this investigation was to determine changes in physical and chemical properties of subbituminous lump coal while in storage for 8 months in a typical residence and to demonstrate how this fuel may be stored without degradation or spontaneous combustion. The second object of the study was to determine how the stored coal performed in a hand-fired furnace operated under practical conditions.The investigation revealed that if care is exercised in placing sub-bituminous lump coal in a closed bin, no significant slacking or degrada¬tion occurs, no hazards arise, and over-all indicated efficiencies of about 65 to 69 percent can be obtained under practical,firing conditions that the average home owner can meet.Owing to the war emergency, much attention is being given to the proper storage of coal, and campaigns are being conducted to increase the quantity of coal being stored to relieve transportation and production overloads. Ordinarily, coal dealers do not recommend storage of subbituminous coal in homes owing to deterioration of the coal and to possible hazards from spontaneous combustion. This practice has grown from some troubles that have been experienced, which can be traced to improper preparation, improper bins, and poor technique in placing coal in a bin. There is no good reason why subbiturninous lump coal cannot be stored safely in homes."

Jun 1, 1944

By D. S. Colby

The productive capacity of natural-gasoline and cycle plants in the United States as of January 1, 1952 was 811,596 barrels per day, an increase of 163,691 barrels per day since the last survey on January 1, 1950. The rate of growth during these 2 years has been 12 percent per year s only slightly below the maximum rate, recorded from 1948-50. This survey, for the first time, presents capacity data on a barrel rather than a gallon basis. Also, for the first time, a break-down of capacity by products has been obtained. The combined LP-gas producing capacity of plants and fractionators equaled 382,790 barrels per day, 47 percent of the total industry capacity tor all products. During January 1952, LP-gas and natural gasoline and other products were each produced at the rate of 76 percent of the January 1 capacity.

Jan 1, 1952

Maps To Accompany Bulletin 418

Jan 1, 1941

By Selim E. Woodworth

This paper, describing the milling practice on the Mother Lode as typified in the mill of the Argonaut Mining Co. at Jackson, Amador County, Calif., is one of a series prepared by the United States Bureau of Mines. The data herein presented and furnished through the courtesy of E. A. Stent, managing director and vice president of the Argonaut Co., covers operations from 1914 through the year 1929.

Jan 1, 1931

By John P. Powell

A comprehensive study of the effects of hydraulically fracturing water-flood wells in Oklahoma has been made by the Federal Bureau of Mines. This report presents results of that study and an analysis of some of the factors governing the results of fracture treatment on waterflood properties. Originally, hydraulic fracturing was used to stimulate oil production from old wells producing by primary methods, and its application to water-flooding was regarded with skepticism by most producers. However, since 1953 the number of fracture treatments of both oil and input wells in waterfloods has increased steadily. Hydraulic-fracture treatments in waterfloods have generally been successful in stimulating production from oil wells and increasing the rate of injection into input wells. Hydraulic fracturing has enabled several producers to turn probable failures into economically successful projects.

Jan 1, 1961

By Paul Hatmaker

This paper covers briefly the particular field of dolomite and magnesium limestone; certain uses of high-calcium limestone are mentioned only to show more clearly the limita¬ tions of the magnesian rocks. Such a comparison is helpful because magnesium carbonate is essential for some uses; for others it is immaterial; and for many its presence in an appreciable amount is objectionable. Magnesium carbonate, occurring as a rock resembling limestone or dolomite, is described in United States Bureau of Mines Information Circular 6437, Magnesite. Other com¬ pounds of magnesium are described in United States Bureau of Mines Information Circular 6406, Magnesium Compounds (Other Than Magnesite). Limestone, geologically, is a rock composed essentially of calcium carbonate; commercially, however, the term may include dolomite and magnesium limestone.

Sep 1, 1931

By Nan C. Jensen, Oliver Bowles

Stone , the foundation of the continents and the floor of the oceans , is one of the most substantial and enduring of all substances that constitute the material universe . Stone furnished rude shelter for aboriginal man , and through all succeeding ages it has provided a lasting and serviceable structural material . Limestone is one of the most widely used building stones .

Oct 1, 1947

By H. Herbert Hughes

Soapstone commonly is associated with talc , and reports on either commodity usually contain a discussion of the other . From a geological or mineralogical standpoint the combination is justifiable , for soapstone essentially is impure talc . Commercially , however , the relation between them is remote . About 95 per cent of all talc sold in the United States is in ground form, whereas practically all soapstone is sold as furnace blocks or as fabricated structural slabs for many and diverse applications .

Feb 1, 1932

By J. W. Thompson, M. N. RICH

That there is wide interest in the preparation and properties of metallic zirconium and its salts is indicated by the many articles recently published in scientific and technical journals and the many patents issued. The compounds of zirconium have numerous important uses and more uses will doubtless be found. In the course of the special work on rare metals that were of military importance during the war, the authors of this bulletin were detailed to the Golden mining experiment station of the Bureau of Mines to prepare metallic zirconium and to investigate its properties. A number of investigations in recent years have indicated that sintered or coherent zirconium metal is very resistive to acids; that it can be used for electrodes, and it probably will find metallurgical uses. A steel containing zirconium has been proposed for use in armor plate and automobile parts, and nickel-zirconium alloys have been suggested for high-speed cutting tools and for cutlery. Numerous articles in scientific journals have recommended the use of zirconium oxide as a refractory, an abrasive, a pigment in paints, and as an opaquing agent in enamel ware. The salts have been used in the textile industry' as a mordant and also for weighting silk. When the authors began their investigation, they found it necessary to collect all of the available literature on the general subject of zirconium and its compounds. Pure salts could not be obtained on the market, and in order to get these, as a preliminary step to the preparation of the metal, the literature had to be classified and the methods of preparing the salts investigated. Also, there was much difficulty at first in making satisfactory analyses, and this phase of the work received careful attention. As it was necessary to begin with a historical review of the literature, such a review is given as Part I of this report, and a bibliography is included as Part IV. References to the numbered items in this bibliography are made throughout the text, the usual footnote references being omitted. Analyses of the products and conclusions as to their purity are given under the descriptions of methods of preparation. A table showing the properties of the amorphous metal, and another showing the properties of the coherent metal, will be found under appropriate headings in Part II. No attempt has been made in the historical review to discuss fully all the published information about zirconium and its compounds, but only such material has been assembled as has a direct bearing upon the present work. Considerable difficulty was experienced in collecting this material because of the confusion of terms by various authors who perhaps did not thoroughly understand the chemistry of zirconium.

Jan 1, 1921

By E. V. Potter

"INTRODUCTION The oscillator and amplifier system described in this paper was developed specifically for driving sound generators of the type developed by H. W. St. Clair and described by him in an article 3/ published several years ago in the Review of Scientific Instruments.Nevertheless, with little or no alteration it can be used to drive any vibrating system in which the vibrating member must be driven at its resonant frequency; the only restrictions are that the driving mechanism be electrical in nature and that the vibrating member be accessible so that some type of pick-up can be coupled to it. Operation of the automatic frequency-control element in the oscillator, however, depends entirely on the operating characteristics of the vibrating member; therefore, in order to completely explain the operation of the circuit, it will be necessary to describe the construction and operation of the vibrator used with it. Only the essential features and characteristics of the vibrator will be described in this article, and the reader is referred to St. Clair's 4/ report for further details."

May 1, 1943

By Leo J. Neill, O&apos

Abrasives are essential to the manufacture of munitions - airplanes, gas, shells, tanks, and in fact every product that involves metal forming or finishing. An indication of the importance of abrasives in the national defense and aid-to-Britain programs is the close peace-time correlation between demand for abrasives and automobile production, which in recent years has consumed more than 35 percent of the total output of abrasives. Unprecedented demands on the abrasives industry are forecast by the rapid expansion in airplane output, tie increased mechanization of all armed forces, and the consequent speeding up not only of the factories where finished munitions are made but also of the steel mills and other factories were additional large quantities of abrasives are needed for snagging or rough-grinding semifinished products before they can be used by the fabricators. A recent survey by the artificial abrasives manufacturers indicates that they can readily increase their output 75 percent compared with the previous peak of 1937 without building new plants. By overhauling production schedules, their maximum production possible could be increased to 182 percent of the 1937 output, and the nature of the industry is such that plant capacity could be increased rapidly if need therefor should arise. No figures on the estimated requirements for abrasives in 1941 or 1942 have as yet been compiled, but the industry feels that it can meet demands as they develop.

Jan 1, 1941