Search Documents

By Alfred H. Bell, George V. Cohee

Illinois produced 146,788,000 bbl. of oil in 1940, or nearly 11.0 per cent of the total for the United States, and ranked fourth among the oil-producing states. Its production was only slightly less than that of Oklahoma, which produced 11.5 per cent of the national total. Illinois' production in 1940 represents an increase of 55 per cent over the previous year, when it amounted to 94,912,000 barrels. The development of the Devonian limestone in the Salem and Centralia fields is largely responsible for the increase in production during 1940 Production from the Devonian limestone in these two fields was estimated to be 36,698,000 bbl., or 25 per cent of the state's total production (Table I). The increase in production during June, when the state's daily average production attained a peak of 518,200 bbl. for the week ending June 29, was due to the Devonian production at Centralia (Fig. I). The initial production of the best Devonian wells in the Centralia field was as high as 12,000 bbl. in 24 hr. Daily average production in IIIinois for 1940 was 400,000 bbl. of oil, but actually daily production fluctuated widely during the year. At the beginning of 1940 daily production was approximately 330,000 bbl. During the first hali of the year it in-creased irregularly to the peak in June mentioned above and as the prolific Devonian producing areas were drilled up, the state's daily production declined rapidly during July and continued to decline, although more slowly, until the end of the year, when the daily production was approximately 325,000 bbl. The daily average production per well in the new fields at the end of the year was approximately 40 bbl. (Fig. I). Oil from the Devonian was also produced in the Bartelso field, Clinton County, the Sandoval field, Marion County, and the Irvington field, Washington County, bringing the estimated total production from the Devonian limestone to about 26 per cent of the state's total production, The remainder was obtained largely from the Mississippian system. About 2 per cent of the total was from Pennsylvanian and Ordovician strata. The decline in the Devonian limestone production has been so rapid that the 1941 output from this system will probably be only a small fraction of that of 1940 unless large new reserves are discovered. The "Trenton" (Ordovician) limestone has been tested in two wells in the Centralia field and both were small oil producers at a depth of about 4000 it. The "Trenton" also was found productive in the Salem field at a depth of 4500 ft. (Table 5). The initial production of the discovery well, which was completed shortly after the end of the year, was 130 bbl. on pump. Other wells drilled early in 1941 had initial productions averaging 172 barrels. The outlook for 1941 is for a continuation of drilling activity in Illinois, but at a declining rate (Fig. I, upper curve). The most active area at the end of 1940 was in the deep basin area in Wabash, Edwards, White, and Hamilton Counties.

Jan 1, 1941

By R. F. Domagala, M. Hansen, D. J. McPherson

Iodide zirconium was combined with calculated amounts of nitrided zirconium sponge and arc melted to prepare alloys in the 0 to 6 wt pct N region. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat-treated specimens permitted construction of the binary phase diagram from 0 to 6 pct N. Features of the diagram include the peritectic formation of both a and ß solid solutions. The maximum solubility of nitrogen is 0.8 pct in 8 zirconium and 4.8 pct in a zirconium. An X-ray study of nitrided materials was made in the range 6 to 13 wt pct N region because serious nitrogen losses were experienced when attempts were made to arc melt these high nitrogen alloys. PHASE relationships in the Zr-N system have been determined. Due to the inability to retain nitrogen in nitrogen-rich alloys subjected to arc melting, definitive work was possible only in the range 0 to 6 wt pct (0 to 30 atomic pct) N. Sufficient complementary X-ray work was done to permit construction of the binary phase diagram up to 13.3 wt pct (50 atomic pct) N (ZrN). Small ingots were prepared by arc melting master alloys with enough zirconium to produce an alloy of the desired composition. Following pretreatment, alloys were annealed at temperature levels between 600" and 2020°C. Determination of the phase boundaries was then accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to corroborate solidus curves, and X-ray diffraction was employed to study the nitrogen-rich region of the a + ZrN phase field. Materials Westinghouse Grade 1 iodide zirconium crystal bar served as the base material for this investigation. The as-received bars were lightly sandblasted, pickled in a 20 pct HN0-5 pct HF aqueous solution, rinsed in water and acetone, and dried. They were rolled to about 1/32 in. strip and acid-pickled, followed by water and then acetone rinses. The material was sheared to approximately 1/4 in. squares, cleaned with acetone, and stored for use. Pure zirconium nitride is not commercially available, according to correspondence with possible suppliers. A literature survey indicated that nitrogen may be introduced into zirconium metal by passing nitrogen or ammonia gas over zirconium at an elevated temperature. After considerable experimentation, a train was devised whereby high quality nitrogen was passed through a series of bubblers to remove the last traces of oxygen, through an H,SO, bubbler and a cold trap to remove moisture, and finally over zirconium within a resistance furnace. Hand-picked Bureau of Mines magnesium-reduced zirconium sponge proved more amenable to nitriding than the crystal bar. The nitrogen used was extra pure gas purchased from Linde Air Products Co. The first two bubblers through which the gas was passed contained a solution suggested by L. F. Fieser" as being ideal for removing the last traces of oxygen from nitrogen. The solution contains 20 g KOH, 2 g sodium-anthraquinone ,9-sulphonate, and 15 g NaHSO, dissolved in 100 ml water. It is blood-red and turns brown when contaminated with oxygen. A saturated lead acetate solution, next in the series of bubblers, removed any H2S which might have formed in the 0, removal stage. An H,SO, bubbler and cold trap removed moisture before the nitrogen was passed over the zirconium. The zirconium was contained in a stainless steel screen within a Vycor or quartz tube in a resistance furnace. Unreacted nitrogen passed out of the system through a mercury bubbler. A nitriding run was performed in the following manner: Zirconium was placed in the screen within the furnace tube. The unit was assembled, suitably clamped off, and evacuated to remove the air and moisture within the tube and that trapped by the zirconium sponge. The unit was flushed with nitrogen and evacuated twice. After nitrogen was allowed to pass over the zirconium for about 30 min, the furnace was turned on; several hours were required to reach temperature. The reaction was allowed to continue at temperature for about 4 hr and the screen was then withdrawn from the hot zone of the furnace by means of a Nichrome or Kanthal rod. The screen and its contents were allowed to cool at the end of the tube and were then removed. At 800°C no more than about 5 pct N could be introduced into the sponge zirconium. This material was designated M-1 (master alloy No. 1) and reserved for the preparation of alloys in the dilute nitrogen region. A second set of experiments was conducted at 1000°C; no more than 7.2 pct N could be introduced into the zirconium at this temperature. Enough material (M-2) of this nitrogen content was prepared to produce a second set of alloys to complement the first and to provide alloys in the 0 to 6 wt pct N range. It was hoped that a diffusion anneal plus a re-nitriding might yield a material of higher nitrogen content. The material containing about 7 pct N was therefore given a homogenization treatment at 1000°C for 6 hr under an argon atmosphere. It was

Jan 1, 1957

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By H. Y. Bassett

THIS paper attempts to show the various major operations used in nonferrous tube mills and does not necessarily represent the current practices at the two plants of the Wolverine Tube Div., of Calumet and Hecla Consolidated Copper Co. Inc. The operations now utilized in the production of tubing are quite varied and show the continual interest and advance metallurgically and mechanically to produce the best quality at the lowest cost. Naturally, any advance or lowering of cost is dependent on large production runs, which mean longer machine running time with maximum worker productivity. Standardization of tube sizes and elimination of unnecessary alloys are therefore very necessary, otherwise the development of costly new production machines would be of little benefit to the consumer as a whole. It should be noted that in such a short presentation it is impossible to describe in any detail the major operations. The short descriptions, it is hoped, will enable all who are interested to obtain a general idea of present, day practices in the copper tube producing field. Fig. I is a flowchart or sequence of operations showing the steps usually employed in tube production. RAW MATERIALS Quality starts with the raw material, and it is absolutely necessary that raw material be controlled and held to rigid specifications. Little need be said, however, regarding the raw materials for the casting of bars or billets, as the material always is purchased and checked against the various governing A.S.T.M. specifications. CASTING Casting, as is indicated in Fig. I, is quite varied and for convenience can be classified into two groups: The casting of solid billets, and the casting of hollow tubes, each of which is the base for subsequent operations. In the melting of the raw materials various types of furnaces are used, and the selection of any one is dependent on many factors outside the scope of this paper. However, as of general interest, a short description will be made of each. Induction Furnace (Low Frequency) This is popular in the melting of copper-base alloys, Fig. 2. In the induction furnace the principle of an inefficient transformer is used for the production of the necessary melting heat. The primary coil is.arranged around a transformer core made of high permeability silicon steel sheet. The secondary circuit is through a melting channel around the primary coil and opens into a hearth which contains the main charge. The heat is generated only in the melting channel, but because of the stirring action there is a constant flow of metal around the channel, which when mixing with the charge causes very rapid melting. The volatilization losses are very low as the furnace atmosphere above the charge is heated only by the heat from the melting metal. The stirring action, however, makes the use of any slag cover difficult. Such furnaces- must be started with molten

Jan 1, 1951

By AIME

AS the Petroleum Division rounds off the first quarter century since its evolution from technical committee status, there steps to the long line of notable men who have presided over its activities a young man, currently of Tulsa, one Herbert F. Beardmore by name. For one year, as Chairman for 1946, the Division will be his oyster. hi; baby, his responsibility. "Herb" Beardmore was born at Columbus, Ohio, Feb. 6, 1904, and lived there until he was thirteen. Then his family moved to Oklahoma City, and later sent him to the University of Oklahoma, where he graduated in 1925 with a B.S. in engineering geology. His final year in college was the first year in which a petroleum engineering course was taught at the school. Since his course of study so closely paralleled that of a petroleum engineer, he has frequently been spoken of as the first petroleum engineering graduate from the University of Oklahoma. Out of college he went to work as an oil-field roustabout in the Ranger, Texas, field for Jake L. Hamon. This work consisted of all manual labor phases of cable-tool operation and beam-pumping of oil wells. He moved in 1926 to Bartlesville, to become a gas engineer for the Indian Territory Illuminating Oil Co., where he was employed in gas-well drilling, gas production, and transportation, mostly in Osage County, Oklahoma.

Jan 1, 1946

By AIME AIME

THE revised program for the San Francisco meeting, with assignment of the various papers to the several sessions is now available and is printed below : MONDAY, OCT. 7 . General Meeting, 11-12 A.M. Chairmen: Frederick W. Bradley and E. A. Hersam. Opening of the session by the Chairman of the San Francisco Section-E. A. Heraam. Address of welcome by the President of the Institute- Frederick W. Bradley. Address: The Mining problems of the West--Charles W. Merrill.

Jan 1, 1929

By Charles E. Locke

SHARP CONTRAST exists in the reports so helpfully contributed by the individual members of the Milling Committee for this review. Those engaged in the milling of gold and silver ores report great activity, of which some details will be given later. Those engaged in milling ores of base metals report continued depression and little progress. Copper production in the United States is running at about fifteen per cent of capacity. Some Arizona copper mills are closed. Anaconda is milling about 45.000 tons of copper ore per month, and the Utah Copper Co. 35,000 monthly. However, in Canada the International and Falconhridge copper-nickel mills and the Noranda copper-gold mill have increased production. Also the Climax molybdenum mill in Colorado is milling 4000 tons per day. Water shortage from the drought has caused curtailment or complete shutdown of mills in some parts of the West.

Jan 1, 1935

By B. A. Stainton, John D. Gill

OUR combined economic activities have as their goal the maximum of individual well-being and national security. In this age of intense international competition the two objectives are closely related. For many decades, the maximum of well-being and ability to maintain national security have moved generally upward. The best single measure-perhaps the only adequate measure -of the level of the rising goal is the per capita real national income (national income corrected for price changes). For centuries before the industrial revolution the income of the world's population changed little from generation to generation. In our country prior to 1800 the growth of national income was hardly measurable from decade to decade. Since 1850, perhaps since the "industrial revolution," the growth of per capita real income has been increasing geometrically. Of major importance is the accelerative growth of the productive ability of our economy. Inadequate consideration of its implications is partly responsible for periodic delays in solving our princi-

Jan 1, 1946

By D. C. Porterfield

ProUuction of crude oil in Venezuela increased from 186,134,000 bbl. in 1940 to 2~8,131,ooo bbl. in 1941, or 22.6 per cent, to establish a new all-time high for the country. While the average production for the year was 625,000 bbl. per day, production during the month of December 1941 averaged 751,000 bbl. per day, and during the last week of the year, 766,000 bbl. per day. Production from the Lake Maracaibo basin averaged 454,000 bbl. per day during the year, or 72 per cent of the total for the country, compared with 73 per cent of the total produced in 1940. Drilling during the year was approximately on the same scale as in 1940, with 438 wells completed in 1941 as compared with 429 the year before. Exploratory completions decreased from 18 in 1940 to 6 in 1941. Of the drilling operations in 1941, 56 per cent was concentrated in the Lake Maracaibo basin and 44 per cent in eastern Venezuela, success being 98 per cent in the Lake basin and 83 per cent in the east. Successful completions for the country as a whole amounted to 92 per cent of the total wells drilled. Exploratory drilling in 1941 resulted in the discovery of three new fields, all in eastern Venezuela; viz., Guara, about II km. to the northeast of the Oficina field but on a separate structure; Santa Rosa, which is east of El Roble field on a structure forming a part of the major Santa -Ana- San Joaquin-El Roble uplift; and Santa Barbara, which is southwest of the Jusepin field on an extension of the main Jusepin anticline. At the close of the year three wildcats were drilling, all of which showed prospects of obtaining production; that is, Mercedes No, 2 in central Guarico, Las Ollas No. I on the Anzoategui-Guarico border near the town of Zaraza, and Quiamare No. I in Anzoategui northeast of the town of San Mateo. In spite of heavy withdrawals and the resultant natural decline in the potentials of older producing areas, new drilling during the year increased the potential production of the country from an estimated 780,000 bbl. per day at the end of 1940 to an estimated 810,000 bbl. per day at the end of 1941, or approximately 4 per cent. Since domestic consumption of petroleum products is insignificant compared with total production, exports of crude and products during the year increased in line with production. Crude exports totaled 196,800,000 bbl., compared with 158,400,-000 bbl. in 1940, and exports of products were 26,100,000 bbl., compared with 21,900,000 bbl. the year before. Exports of crude from Venezuela to the United States amounted to 36,500,000 bbl. In addition, about 2,200,000 bbl. was imported in bond into the United States for transfer to Canada. Total refining capacity of the country in 1941 was approximately 125,000 bbl. per day, including a crude-conversion plant with a capacity of 32,000 bbl. per day, capable of making fuel oil only. Three plants with a capacity of 121,000 bbl. Per

Jan 1, 1945

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

Illustrated guidebooks treating in a popular descriptive way of the geology and other features of the Western United States have been issued by the U. S. Geological Survey. They will be of much interest to mem¬bers in connection with the Arizona Meeting of the Institute and espe¬cially the guidebook of the Santa Fe Route, with side trips to the Grand Canyon, containing as it does relief maps, topographical and geological maps, covering the entire route of the railroad, illustrations from photo¬graphs and other interesting descriptions of this great country. The method of treatment is adapted to the lay-reader, although it includes much valuable and interesting technical information concerning the geographical and other features. The books are well indexed. These volumes sell for 50 c. each and may be obtained from the Superintendent of Documents, Washington, D. C. These guidebooks originally sold for $1 each, but the reprint edition has been reduced to 50 c. A list of the different guidebooks follows: Bulletin 611. Guidebook of the Western United States, Part A, The Northern Pacific Route, with a Side Trip to Yellowstone Park, by M. R. Campbell, and others. 1915. 212 pages, 27 route maps, 27 plates, 39 text figures.

Jan 6, 1916

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.' It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.' It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By Douglas Bunting

(Wilkes-Barre Meeting, June, 1911.) WITH the gradual exhaustion of the upper veins in the anthracite coal-fields, the problem of mining at greater depths acquires increasing importance and demands the consideration of a number of important factors, one of which is the greater earth-pressure and the consequent necessity of stronger support o for the roof. Under the pillar-and-chamber system, almost exclusively followed in the Northern anthracite-field, the highest economy in mining is generally secured by leaving, on first mining, pillars only sufficient to support safely the overlying strata. As to the necessary size of such pillars, the opinions of mining experts are widely divergent. In establishing the width of chambers and pillars, the thickness of vein and its depth below the surface have received little consideration. For. instance, it has been quite usual to work both overlying and underlying veins with the same width of chambers and pillars, when the lower vein was two and one-half times as thick, and twice as fits below the surface, as the upper. In view of the generally-accepted theory that the crushing-strength of coal-pillars of the same base-area becomes less with increased height, it is probable, in this instance at least, that the most economical mining has not been secured. This question of adequate pillar-support is economically less important down to about 800 ft. than at greater depths; and it is with reference to mining at these greater depths that the study of the subject here presented has been prompted. The necessity of leaving larger pillars, involving greater mining-costs per ton and also smaller yields per acre, is one of the troubles of deep working. To mine without leaving adequate pillar-supports will result, sooner or later, in a squeeze. Limited areas, it is true, have been mined at certain widths of

Sep 1, 1911

By T. E. Davidson, C. G. Homan

This report deals with a study of the effects of extreme hydrostatic pressure on a polycrystalline material which exhibits a high degree of elastic anisotropy. Metallographically prepared polycrystalline bismuth samples were subjected to pressure levels up to 20,000 atm in a piston type gas-liquid system. The observed structural changes consisted of deformation localized along the grain boundaries, which appears to be a boundary migration phenomena, and widespread slip and cross slip. Subsequent deformation is progressive with increased pressure, and is substantially different in type from the deformation characteristic of uniaxial compression. A large amount of interest has been shown in recent years in the effects of extreme pressure on metals. In this connection, many investigations into the effects of pressure on physical and mechanical properties and reactions have been undertaken. Due primarily to the experimental difficulties involved, there has not been a great deal of study of the structural changes resulting from exposure of metals to extreme pressure. It has been difficult, for instance, to produce a true hydrostatic stress state in many of the extreme pressure devices used, and also to directly examine specimens metallographically before and after pressurization. The results of a preliminary investigation into one of the effects of extreme pressure, and its associated true hydrostatic stress state, on the structure of metals are discussed herein. Metals exhibit varied degrees of anisotropy in their physical and mechanical properties. Significant among the anisotropic properties is the modulus of elasticity, which varies by a factor of as much as three in some of the fcc metals, and by much larger factors in some of the less symmetrical elements. As a result of the variation of the modulus of elasticity with crystallographic direction, shear stresses will be induced in polycrystalline samples under true hydrostatic compression. Depending on several factors, these shear stresses could become of suffi- cient magnitude to cause localized plastic deformation. Presented herein are some of the structural changes observed in polycrystalline bismuth as a result of exposure to hydrostatic pressures of up to 20,000 atm. Although several other materials in both bicrystal and polycrystalline form are also currently under investigation, bismuth was chosen initially, due to its low symmetry and moderately high degree of anisotropy in the elastic properties. The fact that extreme hydrostatic pressure can induce structural changes in some elements in the polycrystalline state is of importance in itself. However, it may also be a factor in many of the other extreme pressure effects. For instance, this localized plastic deformation could substantially lower the recrystallization temperature, thus altering the effects of extreme pressure on this phenomenon. Also, as commented on by ridgman,' the hysteresis in the polymorphic transition of polycrystalline bismuth under extreme pressures could possibly be attributed to structural changes brought about by unequal compressibility. Therefore, to accurately determine the true effects of extreme pressure on metallic substances, one first must determine if any structural changes due to hydrostatic compression are also simultaneously occurring. The purpose of this work has been to determine whether the shear stresses induced by hydrostatic pressure in an anisotropic polycrystalline material, such as bismuth, could reach a magnitude great enough to cause plastic deformation and to study the resultant structural changes and effects. THEORY In a metallic crystal, the elastic properties are dependent upon the crystallographic direction and plane. Depending upon the degree of anisotropy of the elastic properties and other factors, internal shear stresses of sufficient magnitude to cause localized plastic deformation may be induced in polycrystalline material by true hydrostatic compression. The following highly simplified two-dimensional model of two adjacent grains in a polycrystalline aggregate under hydrostatic pressure serves to schematically demonstrate how these shear stresses arise in an anisotropic material.

Jan 1, 1963

By Robert A. Jankowski, Charles D. Taylor

The objective of this program was to conduct dust surveys at six longwall sections having double-drum shearers, that were regularly in compliance, and to identify the dust control techniques that were the most effective. As each of the mines selected had a record of regular compliance with the Federal Dust Standard, all sampling was "short-term" (often less than 30 minutes) and no attempt was made to relate the survey results to dust-sampling results obtained by the companies for compliance purposes. The sampling procedures (1) used during this survey were developed jointly by the Bureau of Mines and Foster-Miller Associates, Inc. In addition to monitoring dust levels, measurements were also taken throughout the shift to monitor airflow along the face and water usage on the shearer. This program was a cooperative effort of the Bureau of Mines and the Mine Safety and Health Administration (MSHA). The following MSHA health specialists contributed to its successful completion: Paul Lenyo, CMS&H, Dist. 2; Ellis Mitchell, CMS&H, Dist. 3; Carl Jenkins, CMS&H, Dist. 4; David Stritzel, CMS&H, Dist. 8; and John Prelc, CMS&H, Dist. 9. RESULTS CUTTING SEQUENCE - WORK LOCATION At all mines surveyed, an important factor in controlling dust exposure at the shearer is the design of the cutting sequence so as to allow the shearer operator to work most of the time on the intake-air side of the lead drum. It is generally accepted that most of the dust generated by a double-drum shearer comes from the lead drum, which in the raised position normally takes a full sump. Because the position of the drum that is in the raised position determines the horizon control, the operator must be close enough to carefully monitor its operation. Therefore, his position relative to the lead drum has a significant effect on his dust exposure. Dust profiles, such as those constructed from data collected at Mines A and B (Figure 1), show the large gradient in dust concentrations that can exist between the intake and return air side of the lead drum. When the primary cut is taken head to tail, the lead drum is downwind and dust levels can be maintained at a low level until air has passed the shearer (Mine A). Thus, shearer operators can stay in relatively uncontaminated air. When the primary cut is taken tail to head, the lead drum is upwind of the shearer controls, resulting in higher dust concentrations at the shearer operator's work location (Mine B). At the mines where this cutting sequence was used, it was company policy for the shearer operators to walk on the intake side of the lead drum, returning to the controls only to adjust the height of the lead drum. DIRECTED WATER SPRAYS AND PASSIVE BARRIERS It is not always possible to keep the shearer operator on the intake air side of the lead drum. Various techniques have been tried to keep the dust generated by the shearer away from the machine operators when they work adjacent to the shearer. At all mines visited, the external water spray nozzles were directed so that dust from the shearer was directed downwind and toward the face, and away from the shearer operators. The effectiveness of using external water sprays to keep dusty air close to the face was noted during Bureau of Mines efforts to develop improved water spray systems (2). Laboratory and underground tests showed that water sprays located properly and directed downwind can create aiflow patterns that move dust generated by the shearer toward the face and away from the shearer operators. Sprays directed upwind, into the airflow, can actually move dust away from the face

Jan 1, 1982

By R. W. Raymond

THE absence of a convenient glossary of terns connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction ; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place' individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who hays favored me with ' assistance and advice. The labor bestowed upon this paper since its presentation, at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

• Phelps-Dodge Corp. signed an agreement with the Defense Materials Procurement Agency to increase copper production from the east ore deposit of the company's Copper Queen branch at Bisbee, Ariz. The company agreed to undertake a $25 million expansion program, including construction of a concentrating and leaching plant at the Bisbee mine and enlargement of the Douglas smelter. The Government agreed to buy the first 112,500 tons of the first 150,000 tons produced at 22e per lb if the company could not sell at a higher price. The new facilities will have a yearly capacity of 38,000 tons and should be in production by late 1954 or early 1955. • American Smelting & Refining Co. has started construction of a new building to house the Central Research laboratory at South Plainfield, N. J. It will have approximately 75 individual laboratories and an equal number of offices and shops. Modern apparatus to be installed will include electron microscopes, electric and fuelfired furnaces, miniature copper refineries and zinc plants, wire drawing machinery, and large pilot plant laboratory. In the new building scientists study the base metals, and the development of new uses for a number of Asarco by-products, arsenic, and little

Jan 11, 1951

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942