Search Documents

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

Nauru Phosphate, which is one of the world's highest grade deposits discovered to date, contributed in 1969, 2.2 million tons of the total world production of 77.7 million tons. Phosphate production, which is the major source of revenue for the island nation, is carried out by the Nauru Phosphate Corporation, headed by a Government appointed Board of Directors. The complete mining operation, including ship loading techniques, is discussed along with proposals at present being investigated to upgrade the Quality of the product.

Jan 1, 1971

By J C. de Vries

When times are tough in the mineral industry û as they have been for some time û typical responses by mining companies are to cut costs and/ or increase production. The latter is seen to spread fixed costs, thereby also reducing unit costs per tonne mined. However, most mineral deposits respond to increased production rates by lowering ore grades, so the reduction in cost per tonne of ore does not necessarily result in a reduced cost per unit of metal produced. The authorsÆ experience is that this process often leads to a mine plan that is a long way from optimal. Producing to the point where marginal cost equals marginal revenue may work well in a manufacturing operation, but it is not necessarily the best strategy for a mining company with a depleting resource. Variations in tonnage and grade with depth, ore reserve optimism and a variety of other factors conspire to produce variations in production rates and grade that often result in suboptimal outcomes and potential mine failure. Added to this is the focus of industry analysts and senior corporate management on such measures as unit costs and ounces in reserves. This is perceived to have the perverse effect of driving the share price down when strategies are adopted that actually improve the value of the mining operation, and vice versa! Many mine failures can be prevented by a close examination of the tonnage grade curve and an understanding of how margins, net cash flows and resulting business risk change with cut-off grades and rates of production. A few relatively simple analyses early in the evaluation of a project can demonstrate the tradeoffs between the main decision parameters, leading to right-sizing of the operation. Once major commitments to major capital items have been made, and reserves have been publicly reported, optimisation of the operation becomes much more difficult than if it had been done earlier. Such investigations can also identify the upside potential and downside risks associated with factors outside the companyÆs control. Many strategies that may enhance value in the good times significantly increase the downside risk in the bad times. What is often called risk analysis typically looks at superficial issues, and does not evaluate the major factors leading to the potential for financial disaster. This paper illustrates some of these major risks, and demonstrates how they may be fully evaluated so that corporate decision makers can make fully informed decisions that take account of the real risks.

Jan 1, 2003

In order that the processes seen may be followed in their proper 'order, the subject will be dealt with as follows, (1) Wallaroo and Moonta Mines; (2) Wallaroo and Moonta Mines Smelting Works; (3) Broken Hill Mines; (4) Concentration at Broken Hill; (5) Smelting and refining of Lead, Silver, and Gold at Port Pirie. The first acquaintance with the copper region was made at the Yelta shaft and dressing mill of the Parramatta Copper Mines Co. at Moonta. The country rock at Moonta is a hard, tough, felsitic porphyry, the copper lodes having a general strike of N. 30° Kilipping from 500 to 70°. This necessitates shaft-sinking on the lode, and underlay shafts are the rule on the field. The ore is raised in the Yelta shaft in wheeled skips, and consists of ·chalcopyrite, bornite, pseudomorphic hematite, containing, in addition, molybdenite and tourmaline. The ore from the bins at the brace is passed over a grizzly; the over-size is hand-picked into smelting ore, concentrating ore, and waste rock (00 attle ), which is sent below for filling. The under-size is elevated to a trommel having in. holes. The over-size falls on to a picking belt made up of lengths of rope strapped with iron, working over wooden pulleys.

Jan 1, 1907

By A C. Robertson

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authorsÆ personal observations and experience.

Jan 1, 1998

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978

Backfil ling of excavated Sub Level Open Stopes has been underway since March 1989 and as at December 1992 some 1 100 000 cubic metres of Cemented Aggregate Fill have been placed. During these three years significant developments in fill quantities, types and cost have taken place.Operational improvements have reduced the quantity of Cement Aggregate Fill by 40 per cent. These results have been achieved by:ò rescheduling stopes,ò designing smaller primary stope, and ò use of uncemented rockfill.Unit cost for Cement Aggregate Fill have fallen in the order of 50 per cent through:improving fill hole reli ability,simplified barricade construction procedures, reducing the cement content,ò substituting dune sand for deslimed mill tailings, ò improved maintenance at the Backfill plant, and ò renegotiated site freight agreement.This paper will review the historical developments of backfill use at Olympic Dam.

Jan 1, 1993

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

Newmont Australia Limited has for some 15 years mined a number of large open cuts associated with the Telfer Gold Dome deposits. The principal ore body exploited has been the East Flank of the Main Dome where a very high grade gold reef deposit of mixed metal sulphides, grades in excess of 20gA Au, has been mined in conjunction with dissemi- nated mineralisation contained in the overburden material. The main ore body has been under review for some years as an under- ground mine, however due to the ore body widths of less than 1 metre and a dip generally less than 35 degrees and a very weak host rocks earlier studies all resulted in a continuation of open pit mining activities. In early 1988 it was recognised that open cast mining would not be able to mine all of this valuable resource and a feasibility study was commenced to come up with a practical and economic approach to underground mining.

Jan 1, 1991

By Moxon N. T

A series of low shock energy water resistant emlulsion based explosives have been developed by combining inert materials, such as Perlite P500, into the formulation. The material handling, water resistance and explosive properties of these mixtures were determined as a function of inert additive type, density, charge diameter and emulsion base. Of the emulsion bases tested Emulite produced the best and most stable low density mixtures ranging in density from 0.8 to 1.35 g/cm3 producing velocity of detonations (unconfined) ranging from 3000 to 5500 nits. The mixtures could be detonated successfully at these densities at diameters as low as 25mm. Low shock mixtures formed by combining Emulite with Perlite P500 were successfully trailed at the Cadjebut zinc mine in Western Australia. The performance of the explosive, at three densities, was monitored using both continuous and point to point VOD techniques. The fragmentation produced by the blasts were compared by photographic analysis. During this trial the low shock emulsion mixtures were shown to be as effective as the currently used explosives (packaged emulsion) at a significantly reduced cost.

Jan 1, 1990

By Griffiths L, Marshall P

fhis paper describes investigations into drainage of gas from the solid to control outbursts. Initial studies conducted on drainage of shear zones showed that, given enough time, these can be successfully drained. Once drained, they can be intersected and driven through without any activity of outbursts. The results of programme of investigations to determine parameters for drainage from the solid show that gas flow rates from the Bulli Seam on the average are about 2 litres/min/metre length of borehole. But when shear zones are intersected, the flow rates could be as high as 8 litres/min/ metre length of hole. Shear zones can be picked up from pressure measurements 50 - 60 m away and this could give sufficient time to drill through these zones and drain them in advance. Systematic drainage of Bulli Seam at West Cliff Colliery could eliminate or reduce frequency of outbursts considerably. At present drainage holes are being drilled systematically in the seam, with drainage installations on the surface. Gas purity of 80% methane is being delivered at the surface plant.

Jan 1, 1980

By Shatwell DO, Hayward SB, Leach TM

Following acquisition of the Woodlark Island tenement by Highlands Gold Limited, an exploration programme using extensive diamond drilling has confirmed that the style of gold mineralisation is similar to other SW Pacific Rim carbonate base metal gold systems. The two centres of gold mineralisation at Kulumadau and Boniavat-Busai are inferred to be related. to buried porphyry centres localised on NE trending major horst bounding structures. Individual prospects are localised on NW trending cross structures peripheral to the porphyry centres.Gold mineralisation has been derived from the mixing of hot saline magmatic fluids with cool dilute meteoric waters. While the bulk of mineralisation occurs in dilational tensional gash fractures, bonanza grades resulted from fluid quenching in feeder structures. Pre-mineralisation breccias created plumbing systems for hydrothermal fluids and similar paragenetic sequences are defined for Busai and the Kulumadau areas. These include early, distal porphyry, low sulphidation mineralisation, followed by base metal gold and carbonate deposition.

Jan 1, 1994

By K Tungpalan, E Wightman, M Edraki, E Manlapig, L Keeney

The depletion of easily mined high-grade ore bodies resulted in the industry having to exploit lower grade, complex resources (Albanese and McGagh, 2011; Darling, 2011; Randolph, 2011). The trend is now towards mining and processing of low-grade and complex ores (Darling, 2011; Yingling, 1990). Variable geological and mineralogical characteristics, and complex mineralogy and texture can result in large variations in metallurgical response and also cause challenges in processing. (Carson, 1995; Lorenzen and Barnard, 2011; Yingling, 1990). Variability and the complex nature of ores are fundamental sources of risk that often cause the greatest economic impact (Dusci et al., 2007; Williams and Richardson, 2004). Hence it is important to effectively characterise these types of ore bodies and assess their processing performance (ie recovery, grade). To enable this, there is a need for the following: (i) characterisation of geological, mineralogical and metallurgical variability in the ore body; (ii) effective selection of drill core with characteristics that represent the range of ores in the entire ore body. CITATION: Tungpalan, K, Manlapig, E, Keeney, L, Wightman, E and Edraki, M, 2018. A systematic approach of sample selection to predict processing performance of an ore body, in Proceedings Complex Orebodies Conference 2018, pp 67–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

By Hebbard GJ

Vertical crater retreat mining is being used at Zinc Corporation, Limited and New Broken Hill Consolidated, Limited for pillar recovery between previously mined and filled stopes. In order to increase productivity in the older lead lode areas of the mine, particularly in the lower grade sections around the keel of the orebody, score form of longhole stoping was considered necessary.Due to poor ground conditions in the country rock surrounding the ore and the requirement to provide sane wall support during mining, primary VCR mining has been utilised in these areas.At Zinc Corporation, several stopes have thus far been mined by a hybrid longhole stripping - VCR method.

Jan 1, 1985

By Jones M

The concept of precise, accurate timing with Electronic Delay Detonators (EDDs) was first seriously addressed in the mid-1980s and much was made of the cheapness and profusion of digital watches in terms of the likelihood of EDDs also being cheap and easy to produce. Ten years later, with every major explosives company and many electronics groups having instituted projects to capitalise on the promise of these devices, production devices are still to come into general use. In South Africa, Expert Explosives units have been used in most applications during proving trials and more recently for production blasting in underground ring stoping and open cast coal. The outcome has been valuable learning both as to the benefits and technical requirements for electronic delay blasting, and especially, safety aspects. Examples are shown of production blasts which utilised the power of EDDs. It is evident that it is not delay accuracy alone which determines the value of these systems, but the whole robustness, flexibility and ease of delay allocation when harnessing blast engineering knowledge. Muckpile movement and shape, fragmentation and vibration frequencies have shown to be greatly influenced by designs which can be implemented no other way. The flexibility of a system and the power of the software controlling it are crucial in capitalising on blasting potential, which lies in integrating control of blast timing with other developing electronic Technologies.

Jan 1, 1995

By Chaturvedula V. K

Pillar extraction carried out using various methods (split and lift, Wongawilli and Old Ben) involves the formation of narrow fenders (commonly 7 m of coal) formed by driving "splits" for lifting off with a continuous miner. The strata above a split and fender adjacent to the goaf consists of a cantilever beam (usually >3 m thick) that extends from the solid coal and bridges across the fender. Lifting off the fender from the split in safe conditions depends upon the bridging capability of the cantilever and the fender strength. The nature and competence of the immediate and near roof, the support capability of the coal fender and the presence of faults and or joints can adversely affect the bridging behaviour of the cantilever. Insufficient knowledge of these parameters can lead to extraction under dangerous conditions. Remnants of fenders ("stooks") also support the cantilever and their dimensions are critical to obtain regular caving and goaf falls. Stook area, goaf roof span and roof stand-up time after lifting can be related and only a relatively small increase in stook area of 10-15 m2 can lead to a significantly increased stand-up time, especially under a massive roof. Such conditions strongly influence the re- distribution of abutment stresses and can create increased outbye pillar loading. Based on detailed underground geotechnical investigations, it is concluded that strata caveability, roof cantilever behaviour, fender H:W ratio and remnant stook size are all critical parameters for successful and safe pillar extraction.

Jan 1, 1992

South Australia was founded as late as 1836, forty- eight years after New South Wales, yet within five years had announced the first discovery of metals in Australia. Throughout the 1840s the mining of silver-lead, then copper, spread north through the Mount Lofty and Flinders Ranges creating a thriving industry, years before the discovery of gold in the eastern colonies in 1851. The first significant mine was Kapunda (1842), followed by the much bigger Burra (1845) and other copper finds at Tungkillo, Worthing, Cal- lington, and North Rhine.

Jan 1, 1987

Coal washing practice can be improved not only by critical examination of the plant being operated but also by studying plants operated in other areas. The developments at the Australian Iron & Steel Pty. Ltd. plants are discussed in relation to experiences there as well as developments which have taken place in Queensland in recent years. Early A.I.S. problems involved small coal cleaning in heavy medium cyclones and flotation. A proposed future plant flowsheet for A.I.S. is considered in the light of these experiences. Reference is made to plants operated by the Thiess, Peabody, Mitsui Coal Company Pty. Ltd. at Moura and the Utah Development Company's plants at Blackwater and Goonyella in the development of coal washing prac- tice in Australia.

Jan 1, 1975

INDEX OF CONTENTSBlast Furnace SlagsForehearth AccretionsConverter SlagsConclusionsIllustrationsCOMPOSITION OF SOME COPPER SLAGS FROM PORT KEMBLASamples of copper slags from the Port Kembla Smelter of the Electrolytic Refining and Smelting Co. of Australia, Pty. Ltd., have been submitted for mineragraphic examination, with reference to the mode of occurrence of copper in them. The samples included (I) blast furnace slags, (H) a forehearth accretion, and (IH) converter slags. 1. BLAST FURNACE SLAGS Four series of samples of blast furnace slag have been submitted. The. chemical compositions of the several slags are shown in Table 1. Analyses Nos. 1 and 2 are of samples of slowly or normally cooled slag, taken from the slag dump, Analyses Nos. 3 and 4 are of samples comprising slowly or normally cooled slag, together with granulated slag from the same melt.

Jan 1, 1949