Search Documents

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

By B Bradák, D Asahina, S Saydam, S Akdag

Human exploration of Mars has been on the horizon of scientific goals for decades now, and as part of the objectives of human missions to various planets, one of the possible goals is opening new economic frontiers by the potential extraction and utilisation of resources, eg mining minerals and using surface regolith (Neukart, 2024). A comprehensive understanding of surface morphology, lithostratigraphy, basic structural geology, and civil engineering technology is essential to conduct mining operations for resource extraction on extraterrestrial planets. For instance, proper assessment of the risks associated with excavation and infrastructure construction under unique environments such as low gravity, surface irregularities, and the presence of regolith is fundamental. Such knowledge has been accumulated through satellite imagery and numerical topographic data using remote sensing technology, as well as seismic surveys by the on-site lander (Knapmeyer- Edrun et al, 2021; Banerdt et al, 2020; Giardini et al, 2020). Recent studies show that Marsquakes could be caused by the release of strain energy generated by the contraction of Mars. In particular, Marsquakes occur around the graben where many faults exist and form regularly spaced patterns. This implies that Marsquakes occur when the stress field of the Martian crust is an extension condition, and normal faults appear on the surface. In this study, we focus on so-called graben structures, one of Mars’s common tectonic structures (Plescia, 1991; Banerdt et al, 1992; Hoogenboom Hagen, 2014). The study aims to provide additional information about the tectonic environment during the formation of such features and, in addition, the internal mechanical-rheological structure of Mars, revealed by the geometrical pattern of faults modelled and simulated in a laboratory environment.

Sep 1, 2024

By N Fullelove

The Renison Bell Tin Mine on the West Coast of Tasmania has recently installed a new underground ore handling system incorporating underground crushing, conveying and hoisting facilities. Contracts for the sinking of the shaft and the development of the mine were let and managed by the operator, Renison Limited. Hardcastle & Richards was responsible for the design, procurement and construction management of the fixed plant and equipment including civil, structural, mechanical, electrical and instrumentation services. The system demonstrates worldÆs best practice in design and incorporates a state-of-the-art integrated control system allowing the entire system to be controlled by a single operator located in the underground crusher chamber. A rapid construction period was achieved, despite the difficult and constrained underground environment, without affecting the ongoing operations of the mine. The mine, which was established in the mid-1960s, had previously operated by trucking ore to the surface via a decline. Truck haulage distances and costs had increased as the mine became deeper over the years. By the 1990s it had become apparent that, in order to remain economically viable, it was necessary to reduce truck haulage distances and allow the mine to go still deeper to access orebodies such as Rendeep beneath the current workings. The Internal Shaft System achieved this by eliminating approximately 5 km of truck haulage. It allows the production rate to be increased to up to 1 Mtpa compared with a limit of 628 kt per annum by direct truck haulage to surface. The access it provides to the Rendeep ore and other deep orebodies greatly increases the amount of ore which can be economically mined.

Jan 1, 1998

The concentrating plant of the Broken Hill South Limited was described in Proceedings No. 44, Australasian Institute Mining and Metallurgy, December, 1921, by Wainwright and Read. It was erected on the present site in 1907 and 1908.From that date, the plant has undergone various alterations consistent with metallurgical improvements. By 1925, the timber work of the gravity secti"on had seriously deteriorated, so much so, that, when the machinery was working, the floors and supports vibrated badly, causing heavy maintenance costs.In 1928, it was decided to erect a new gravity-treatment section, to be followed later by a new flotation section.

Jan 1, 1932

By Lawrence L. J

The Australian Broken Hill Consols Mine, situated some 600 yd east of the main Broken Hill line of lode, is noted for its rich ores of silver. In contrast to the vast conformable orebodies of the Broken Hill field, the Consols lode occupies a narrow fissure dipping to the south west at angles increasing from 240 through to vertical and transgressing the strike of the metamorphosed country rock at an oblique angle. This feature, together with the abundance of calcite and siderite and the virtual absence of silicate minerals in the gangue, has led to its classification as an orebody of the Thackeringa type (King, 1953). Recorded production during the period 1890 to 1903 is given as 845,000 oz of silver and 20 tons of lead.The unusually rich silver values of the Consols lode were concentrated at the intersection of the fissure with beds of amphibolite, whereas in the adjacent schists and gneisses the lode became markedly impoverished. From the surface to a depth of some 120 ft extensive surface oxidation had occurred, resulting in the breakdown of siderite and its replacement by limonite and associated manganese oxides.Silver halides, dyscrasite, acanthite and partly oxidised tetrahedrite were the main silver minerals in this zone. With increasing depth the lode material gradually reverted to minerals representative of the hypogene zone.The only previous work specifically on the mineralogy of the Consols lode is that by Smith (1922), one time manager of the mine. His zeal as a mineral collector resulted in much valuable information being available on the distribution of the minerals. More recently, Garretty (1943) noted the...

Jan 1, 1962

By T C. McCuaig, D B. Mapleson

The Wannaway Deposit is a structurally modified komatiite-hosted nickel-sulfide deposit. Until recently, nickel sulfide accumulations surrounding the Widgiemooltha Dome had been studied with a focus on understanding volcanological aspects of komatiite flow regimes and nickel-sulfide accumulation. Although volcanological features can be observed at Wannaway they are overprinted by several generations of structures associated with multi-phase deformation of the Dome. On the mine scale, two significant deformational events can be distinguished that control ore distribution. The first deformational event is represented by the formation of a layer parallel foliation within the footwall metabasalt and boudinaging of the ore into two distinct orebodies (mega boudins) during a north-south compressional event. Evidence of a second compressional event (east-northeast-south-southwest) is defined by reverse > dextral thrust-folding of the ore zone. The latter deformational event focussed the sulfide ore into thrust front positions where folded ore sequences are mined with stope widths up to nine metres wide. Later stage compressional and extensional deformation phases are observed but have minor, localised effects on the geometry of the ore zone. Four orders of control on the geometry and distribution of ore are interpreted through a combination of primary and secondary features observed at Wannaway. Extending the structural aspects of the secondary overprint features into areas of potential mineralisation has not only defined targets for extensions to the Wannaway Deposit, but has also aided to delineate high grade mineralisation and aid mining decisions. Obtaining an understanding of the volcanological conditions of formation, and more importantly, the structural evolution of the Wannaway region has been an integral part in optimising production.

Jan 1, 2003

By G Yeowart, P D. Munro

The Prominent Hill copper-gold concentrator of OZ Minerals Limited in South Australia was built in 2008 and commenced commercial production in early 2009. It has a design ore throughput of eight million tonnes per year (Mt/yr). While the flow sheet has many items in common with other plants treating ores from iron oxide-hosted copper-gold deposits, the Prominent Hill concentrator also has some unique features. Plant design has been based on a 'template' of the very successful Ernest Henry concentrator. Initial options considered for processing Prominent Hill copper-gold ore are briefly examined as well as potential complications arising from the presence of a considerable tonnage of 'gold-only' material present in the deposit. Metallurgical test work and the subsequent decisions leading to the selection of a conventional crushing, semi-autogenous grinding (SAG) and rougher flotation circuit is discussed. One particular difference with other plants treating this ore type is that metallurgical tests and mineralogical studies identified that rougher concentrate had to be reground to a P80 of 20 - 25 microns or finer for adequate liberation of fluorine-bearing minerals. Subsequent satisfactory separation of fluorine-rich gangue material from the valuable copper sulfides requires highly efficient cleaner flotation to make a commercial quality copper-gold concentrate. Xstrata Technology's IsaMillÖ and Jameson Cell technologies developed to meet similar taxing fine grinding and flotation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province were selected for regrinding and cleaner flotation. Plant design has features aiding ergonomics for ease of operation and maintenance not commonly seen in recent projects with large sulfide flotation concentrators.

Jan 1, 2009

By H Arvidson, D Guibal

This paper presents updated interpretations of controls on mineralisation in C Deposit and highlights structural features that influence the geometry of mineralisation domains used in resource estimation. The Area C mining lease is located in the central Hamersley Province, ~100 km WNW of Newman, Western Australia, and contains resources of approximately 1100 Mt of Marra Mamba and Brockman iron mineralisation. C Deposit is located within Area C, on the northern limb of the Weeli Wolli anticline, and mineralisation is hosted predominantly in the Mt Newman Member of the Marra Mamba Formation. Production from C Deposit began in August 2003, following mining of a 950 000 tonne bulk sample in 2002. Recent mapping in the bulk-sample pit and updated interpretations by BHP Billiton geologists have highlighted the significance of structural controls on mineralisation in C Deposit and their influence on the thickness of mineralisation, which ranges from 20 to 80 metres. Structural controls on the geometry and continuity of mineralised domains include south-dipping thrust faults that developed along the Mount Newman/West Angela contact, folds associated with thrust fault development, steeply dipping stratigraphic contacts in the hanging wall of the thrust faults, and gently north-dipping stratigraphic contacts. Thrust faults and folds in C Deposit are significant for two main reasons: their formation resulted in the thickening of the main ore-hosting units in the Mount Newman Member; and faults and folded stratigraphic contacts provided conduits for supergene metasomatic-enrichment processes that produce high-grade iron mineralisation.The implications of this interpretation for the definition of the resource estimation domains are discussed, and suggestions are made for a better integration of geology into the data acquisition and estimation process.

Jan 1, 2005

By Butt C. R M

Resurgence in Au exploration during the past decade has been characterised by a considerable emphasis and dependence on geochemical procedures. This has been made possible, firstly, by marked improvements in analytical sensitivity over those previously available and secondly, of particular importance to exploration in Australia, by a better understanding of the distribution of Au in the regolith, which has led to the optimisation of sample media. These developments have given exploration companies the ability to seek and detect subtle and widespread geochemical signatures of concealed Au mineralisation and provided an enhanced capability to interpret the data. As a consequence, several new discoveries have been made, even in areas that have been intensively explored in the past. In the deeply weathered Yilgarn Craton (WA), and in equivalent areas elsewhere in Australia and overseas, Au has accumulated in the upper lateritic gravels and duricrusts of the regolith, probably during humid climatic periods in the Tertiary. The laterites may not only be Au ores in themselves, but research by CSIRO and CRC LEME has shown them to be very important sample media, (eg Anand and Smith, 1992). In many areas, however, the laterite has been eroded and hence is unavailable as a sample medium and chemical modification under more and conditions since the Tertiary has leached Au from the upper saprolite. This has greatly increased the difficulties of exploration, particularly where reliance was placed on sampling between 2 and 15 m of the surface. Further research, however, has demonstrated that, despite this leaching, recent remobilisation of An has caused it to concentrate in a specific soil component, pedogenic carbonate, usually in the top I - 2 m, thereby giving surface expression even to mineralisation that is concealed by over 20 in of leached overburden. Secondary carbonates, commonly referred to as calcrete, may precipitate as calcite and/or dolomite in regoliths where the average annual rainfall is less than about 600 mm. Pedogenic carbonates are those that form in unsaturated (vadose) soil horizons. They are widely distributed in the Gawler and Yilgarn Cratons. In the Yilgarn Craton south of about 30¦S ('the Menzies Line'), they are seemingly more abundant over more basic rocks and towards the south east (Figure 1). In contrast, groundwater calcretes form in saturated (phreatic) environments, typically in the axes of major drainages north of the Menzies Line. These are known to accumulate economically-significant grades of U but not, apparently, An.

Jan 1, 1997

Incidental to the progress of a geological survey of the Kalgoorlie goldfield during 1927-28 a number of specimens of telluride minerals were obtained, chiefly with the help of Mr. F. G. Brinsden, general manager of the South Kalgurli mine, and Mr. Ernest Williams, general manager of the Boulder Perseverance mine. This collection was supplemented by a number of small specimens, including the rare copper telluride, which were collected and preseryed from the Kalgurli mine by Mr. A. E. Paton, and also by a few miscellaneous specimens from the collection o{ Mr. S. F. C. Cook, of the Palace Hotel, Kalgoorlie.An extensive knowledge of the rare tellurium-bearing minerals was compiled during the last century from occurrences in Transylvania and Colorado. The recognition of different species has been based on chemical analyses and crystallographic measurements. In a few species there has been an absence of crystalline form, and these, together with the discoveries in this century of rickardite and "weissite" muthmannite and empressite, have depended chiefly on the chemical analysis for identification. On the other hand, the crystalline form of nagyagite and stiitzite has been described in detail, while their precise chemical formulae were doubtfully defined.

Jan 1, 1931

By D Johansson, C Yi, U Nyberg

Emulsion explosives are a common industrial explosive and have a non-ideal detonation behaviour. The detonation performance for a given product changes with the charge diameter, ground conditions, con?nement and density. The burning process of an emulsion explosive has been modelled with an ignition and growth model in the LS-DYNA code. The parameters in the burning rate function are calibrated by the detonation velocities and the detonation front curvature radii from emulsion explosive tests. A Perl program was developed for an efficient estimation of the parameters, and the results show that the calibrated parameters can predict both detonation velocities and the detonation front curvatures.CITATION:Yi, C, Nyberg, U and Johansson, D, 2015. Parameter determination of an ignition and growth model from emulsion explosive tests, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 585–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

Mining projects frequently fail to meet their financial objectives. A significant area of poor performance lies in the areas of resource estimation, reserve definitions, selective mining and metal accounting. The processes leading to the exploi

Jan 1, 1998

By Urabe T

In June 1989 a diving cruise of the French submersible Nautile has been carried out on the North Fiji basin spreading ridge. The objective of the cruise was the geological and geochemical study of the active spreading axis and associated hydrothermalism processes. This operation was the third cruise of the French-Japanese STARMER project following two cruises of the R/V Kaiyo in 1987 and 1988.INTRODUCTIONAfter the Seapso III cruise (Auzende et al., 1986, 1988a and b) of the R/V Jean Charcot in 1985, the objective of the Kaiyo 87 and 88 cruises was the complementary Seabeam mapping of the North Fiji Basin spreading axis between WS and 22'S and a systematic sampling (water and rocks) and deep towing (TV and photos) at about every ten milles along the axis.

Jan 1, 1990

By Lumley G. I, Hayes H

Non-intrusive methods for the reliable determination of dragline bucket and rigging performance have been achieved using physical modelling. Modelling offers a logical first step towards developing mathematical simulation models. The process of physical modelling has been applied successfully to predict dragline bucket performance and capacity as well as to demonstrate the effect of varying dump rope length on performance. ACIRL's Surface Miming Group has used physical modelling to carry out dragline bucket sizing for a new high productivity bucket and compared performance with Throng Coal's existing dragline bucket. The predicted bucket performance has since been confirmed in the field using dragline monitoring techniques.

Jan 1, 1992

Performance trials followed the commissioning of three large mine fans at Mount Isa in 1965. Actual performance characteristics were determined. These were in good agreement with predicted performance. Piezometer rings for volume flow and pressure measurement were calibrated, and the performance of some aerodynamic components of the installation was studied.Test equipment, preparation, and conditions are described.

Jan 1, 1967

In recent years a large number of Horizontal Belt Filters have been installed in the Australian mining and chemical industries. This paper deals briefly with the general background and advantages leading to the selection of this type of filter. Several different applications are described and particular reference is given to the simplification of the fines treatment circuit at the South Bulli Coal Washery.

Jan 1, 1989

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

The areas of impact when employing high productivity long wall systems are reviewed and the financial implications of the most significant areas highlighted. A distinction has been made between availability and utilization. The need for more efficient delay recording, together with increasing control and utilization of the systems has been identified and the measurability of the latter discussed. The increased use of electronic delay reporting direct from the operating unit as the basis for operational control and a pre-emptive maintenance philosophy is seen as an important area of achieving higher performances from existing long wall production systems and Configurations.

Jan 1, 1988