Search Documents

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

By Parfitt RL

A quarter of the North Island, New Zealand is covered by weathered volcanic tephras of mainly andesitic and rhyolitic compositions. Rapid weathering of basic volcanic glass and slower weathering of acidic glass have produced short-range order alumino-silicate clays such as allophane. Although amorphous to x-rays they have a high degree of local structure. Allophane comprises hollo spheres of approximately 40 diameter and 7 X wall thickness. This small particle size and morphology gives a very high surface area (up to 800 m2/g). Ferrihydrite is another short-range order clay of similar small size and high surface area; it has ò formed from the rapid oxidation of water containing ferrous iron derived from volcanic rocks. The quantity of allophane present in tephra depends upon the climate, the nature of the volcanic glass and the time it has weathered. In New Zealand highest amounts (-50%) occur in beds of andesitic ash deposited on old ignimbrite surfaces with mean annual rainfalls >1600 mm. Both allophane and ferrihydrite will react with oxyanions, such as phosphate, arsenate or borate, and remove them from solution. Other anions such as fluoride also react with aluminium sites on the mineral surface. At NZ Soil Bureau, Department of Scientific and Industrial Research (DSIR), New Zealand, techniques have been developed for granulating allophane to enable it to be used to remove pollutants from solution without dispersion into the liquid phase. This granulated allophane can be used to remove phosphate from sewage effluent or fluoride from tap water without having a sedimentation stage to remove the clay.

Jan 1, 1987

By R Skirrow, E Bastrakov, A Mauger, P

A new rapid spectroscopic core and chip logging and imaging system developed by CSIRO was evaluated by PIRSA and GA on a wide variety of mineralised properties in South Australia, including the Emmie Bluff, iron oxide copper-gold-style prospect on the Stuart Shelf. During a three-month campaign in South Australia in 2003 the system logged over 50 000 metres of core from the State Core Library, company prospects and mines. The new system uses automated core tray handling, continuous visible and infrared spectroscopy, and digital imaging, to characterise and identify dominant mineral species on core, chips and pulps, at spatial resolutions of ~1 cm (spectral data) and ~0.1 mm (image data). The system can log up to 1000 m of core per day and several thousand metres of drill chips. Mineralogy is pre-interpreted using specialised identification software trained on a selected suite of minerals showing characteristic absorption features within the measured spectral range. On core from the Emmie Bluff iron oxide copper-gold prospect, 470 km NW of Adelaide and 80 km SSE of the Olympic Dam Cu-U-Au deposit, the spectral mapping system was able to characterise a number of alteration zones enveloping the sub-economic Cu-Au mineralisation. These consist of distal white mica phases showing decreasing Al content towards mineralisation, a zone of increased iron oxide content in the hangingwall to mineralisation, and a zone proximal and coincident to Cu-Au mineralisation that is enriched in chlorite with variable Mg/Fe chemistry. Additionally the results show background spectral characteristics that mimic the magnetite distribution.

Jan 1, 2004

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

Traditionally, surface coal mines in the Western United States have been limited by economics to depths between 150 to 200 feet. Utah International Inc., however, is now planning to strip coal its San Juan Mine in Northwestern New Mexico to depths ranging up to 400 feet while uncovering 20 feet of steam coal. This method is cost-competitive with nearby shallower coal deposits and underground mining of the same property. How trucks and shovels can pre-strip for a dragline, along with results of the planning process, comparison with alternate systems, capital requirements, operating costs and comparisons with other coal sources are all detailed. Also discussed are the major problems anticipated, how they might be corrected, and potential improvements to the concept. Introduction The San Juan Deep Stripping Project will be situated at Utah International's San Jean Mine. The mine is in the Four Corners region, so-called because four states enjoy a common border point about 30 miles to the northwest.(see Figure 1). The area is a semi-arid plateau region with an average elevation of 5,200 feet, receiving an average of 6 inches of precipitation annually

Jan 1, 1981

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

Pasminco is actively addressing the optimal utilisation of the known orebody at the Broken Hill mine, in addition to actively exploring for economic mineralisation in the region. As part of the policy of better utilising the known mineralisation a major upgrade of geological systems at the mine was initiated. The software chosen for this change was Maptek's Vulcan, mainly because of the ease of use of this package. Rather than having numerous data sources in varying software packages the mine aimed to limit interfaces and packages. The decision to upgrade the mine's software was not taken lightly, especially in view of the inature stage of Broken Hill mining operations. However, the current mine life of Pasminco Broken Hill mine is I I years, which is longer than many new mines setting up in Australia today. Also, a more sophisticated system brings with it a better understanding of the economic mineralisation, possibly extending the mine life further. The process of moving the Broken Hill databases into Vulcan was a huge task which included, database transfer, digitising, wire framing, modelling and eventually ore resource calculation. To ensure the validity of the new ore resource accounting system, the existing system was run as a duplicate for the introductory year, providing a comparison and if necessary a safety net. The benefits of such a change, however, became apparent almost immediately. Area geologists realised the opportunity to revise geological interpretations in their areas of responsibility, enabling them to obtain a better understanding of orebody morphology. Three- diniensional analysis provides an excellent method by which review of ore targets both in the underground and mine lease exploration areas can he made. As each new find of mineralisation enters the system and hopefully extends the mine life, the opportunities for further mineral exploration in Broken Hill area by Pasminco are enhanced.

Jan 1, 1997

By J Chßvez, J Rosa del Castillo, J Rui

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11 km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River in the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (eg Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the æTechnical FeasibilityÆ phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralisation/ precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru SA, and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the AMD could be sufficiently treated to be potentially used to supplement the drinking water supply of Lima, and for agricultural (eg irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for implementation of the full-scale treatment facility at the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2003

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By B, R E. Browner, H R. Watling

A number of hydrometallurgical treatment methods are being developed to extract copper from chalcopyrite flotation concentrate including microbial leaching and ferric sulfate leaching. However, chalcopyrite is difficult to process efficiently by hydrometallurgical methods as it exhibits slow reaction kinetics. Comparative leaching tests do not always satisfactorily explain or predict observed copper recovery, acid consumption, or differential leaching of minerals. This is especially true when reactive gangue constituents are present. The aim of this study was to determine how the leaching regime (microbial versus ferric sulfate) affects both the extraction of copper and residue mineralogy. Chalcopyrite flotation concentrate was leached at 30¦C and 65¦C using a pure culture of Acidithiobacillus ferrooxidans and a mixed consortium of thermophiles, respectively. In addition, the concentrate was leached at the same temperatures using 0.1 M ferric sulfate. Microbial leaching of chalcopyrite extracted more copper than ferric sulfate oxidation of chalcopyrite at 30¦C, demonstrating that the microbes promoted the solubilisation of copper at this temperature. This result was confirmed by leach solution analyses and residue analysis using quantitative X-ray diffraction (QXRD). More chalcopyrite was oxidized with ferric sulfate at 65¦C than at 30¦C (as expected). QXRD confirmed that pyrite reacted during ferric sulfate leaching at 65¦C but was relatively unreactive during lower temperature leaching. The high ferric ion concentration in the ferric sulfate leach at 65¦C led to significant precipitation of jarosite. This phase was only detected in small amounts at 30¦C in both the microbial and ferric leached residues. Sulfur also precipitated in the ferric leaching at 65¦C whereas no sulfur was detected in the microbial leached residue. Quartz was a relatively unreactive mineral phase regardless of the leaching medium and temperature. QXRD analysis indicated the residue mineralogy differed with different leaching regime.

Jan 1, 2004

Copper entering a lead ,smelter in concentrate or from other sources is recoVered as matte and speiss which contain appreciable quantities of lead. The matte and speiss are usually sold to copper smelters to recover the copper content and also any gold and silver in these products, but the value of the lead is largely lost. Some copper plants pay for portion of the lead content, but regarded as a means of recovering lead it is more costly and less efficient than if the lead were recovered at the lead smelter.Because of the value of this lead loss, the metallurgy of copper recovery has assumed greater importance in recent years owing to the rise on the price of lead.Two processes are in use today to produce matte and speiss, namely the iron matte process and the soda matte process developed by the American Smelting and Refining Co. 1 in D.S.A. The latter process is characterised by a higher copper to lead ratio than the older iron matting process.The following analyses are typical of matte and speiss produced at Broken Hill Associated Smelters, by both processes, although the soda matte process is still in a developmental stage and experience indicates that matte and speiss of lower lead tenor can be produced under favourable conditions.

Jan 1, 1951

By Ross R

Although mining is an old industry its management is quite a new science, and its complications are now being recognised as demanding expert knowledge in many branches of technical and professional education. Not the least amongst these isaccountancy, for probably its most important problem is "How to control the expenditure." Unlike most businesses a mining company stands almost entirely in the light of a purchaser in the world's markets, and not as a seller, except say for product so the established and perfected systems of modern industries cannot be adopted for mining purposes. For this reason it has been left for late years to consider the matter seriously, and now a number of well-managed concerns have devised costs systems to suit their own requirements.Very little, however, has been published and even that is disjoined and difficult to make use of. Some of the costs systems in vogue, although elaborate and imposing, are not of very great value for keeping check on wasteful expenditure, or for displaying the commercial effect brought about 'by any particular change in practice, or by an addition or alteration to a portion of existing plant.

Jan 1, 1911

By N S. Rauert

The Barrick Gold Granny Smith underground operation located at the Wallaby deposit is currently in a transition period from a near surface operation in ramp up mode to a fully operational deep mining operation with annual production exceeding 1 Mt/a. A key element in this process has been the project execution of the Wallaby Deeps project from initial scoping study in 2007 to the major production component of the Wallaby operation by 2013.The Wallaby Deeps project serves as an example of how an ongoing detailed study program can be integrated into a day to day mining operation assessing risk and mining application in a perceived challenging narrow vein geotechnical environment prior to mining. A detailed study phase to feasibility level is carried out prior to the mining each zone of Wallaby with mining approval only granted on study completion with full justification.A central element in this process is an optimisation study that utilising the Mineable Shape Optimiser (MSO) and Schedule Optimisation Tool (SOT) software tools developed by AMIRA Ltd PRIMO research project is used to carry out an NPV value based option study. This optimisation process being then tempered to reality by a predefined practicality assessment process utilising extensive peer review by operational and study team members as well as industry experts.Other challenges facing the Wallaby Deeps project include the requirement to maintain the ramp up production profile to full production by 2012 without disruption but with pressures of an ongoing geological resource to reserve conversion program essential for the study process and mining approvals and also development rate achievement.To date these challenges are being met with integrated planning and the value of the study program itself. Production in 2012 year to date is well on the way to annual production rate exceeding 1 Mt/a.CITATION:Rauert, N S, 2012. Wallaby Deeps - from the optimal opportunity to reality, in Proceedings Narrow Vein Mining 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By M J. Sale

The Epithermal and Mesothermal Gold Prospectivity Modelling Projects recently completed by Crown Minerals provided explorers in New Zealand with a new compilation of historical exploration data combined with new geological information from the GNS QMap 1:250 000 scale mapping project. These data were used to produce predictive mineral potential maps for gold mineralisation in New Zealand. The aim of these projects, which was to stimulate mineral exploration and investment in exploration, has been successful with new companies acquiring new tenements and committing significant exploration expenditure to exploring in New Zealand in the coming years. The projects were undertaken at a national scale and consequently not all exploration data were compiled into the prospectivity models. HPD New Zealand Ltd recognised the value of the prospectivity modeling work and committed exploration funds to continue the modelling process started by the projects. They recognised the need to compile the remaining data and run the models again to allow detailed exploration targeting.

Jan 1, 2004

By Bourne R. W, Smith T

This paper presents initial findings of a project examining novel processes for the treatment of refractory sulphidic gold concentrates. Non-oxidative roasting of such concentrates for 12 hours at 750¦C resulted in the finely disseminated gold agglomerating to form discrete grains. The pyrite and arsenopyrite decomposed to form pyrrhotite, whilst the labile sulphur and arsenic driven off was collected on a condenser as a mixture of elemental sulphur, metallic arsenic and various arseneous sulphide compounds. As a result, the cyanide solubility of the gold contained in sulphidic refractory gold concentrate from the Emperor mine in Fiji improved from 54.5 per cent to 98.4 per cent; from the Fimiston mine in WA (65.2 per cent to 96.6 per cent), from the Windarra mine in WA (69.6 per cent to 91.3 per cent), from the Harbor Lights mine in WA (20.4 per cent to 60.7 per cent), and from the Wiluna mine in WA (12.6 per cent to 28.0 per cent). The non-oxidative roasting conditions have not been optimised for each of these minerals. Subjecting the non-oxidatively roasted minerals to mild oxidative acidic iron sulphate pressure leaching (with typical temperature of 100¦C and typical oxygen overpressure of 500 kPa) to remove iron and so further liberate finely disseminated gold, resulted in the cyanide solubility of the gold exceeding 96 per cent for each of these five concentrate types (including those from Harbor Lights and Wiluna). Thiourea leaching of the sulphur-rich residues under acidic conditions resulted in remarkably high gold extractions being achieved. These novel processing options need to be optimised, and their economic viability established.

Jan 1, 1991

By D La Rosa, A Jankovi, A Dance, W Valery

This paper presents the methodology for optimising blasting and comminution processes in terms of fragmentation developed by Metso Minerals Process Technology Asia-Pacific and South America (MMPT). The methodology is called process integration and optimisation (PIO) and involves a number of steps: benchmarking, rock characterisation, measurements, modelling/simulation of blasting and comminution processes and where required, material tracking. The measurements collected while at site are combined with rock characterisation and definition of ore domains to model the complete process chain. These data are used to develop site-specific models of blast fragmentation, crushing, grinding and flotation. This allows customised blast patterns to be developed that optimise both crushing and grinding performance. For each domain, blast designs are recommended to generate the optimal fragmentation size for downstream processes. The objective is to minimise the overall cost for the entire process and the changes often have a positive impact on the mining operation. Process constraints such as wall stability, ore dilution, muck pile characteristics, size of mining equipment, size and installed power of crushing and milling equipment and other process bottlenecks are considered in the blast designs. This methodology has allowed many operations around the world to significantly increase their production: generating typically five to 20 per cent higher concentrator throughput. A number of case studies will be discussed in this paper to describe the structured approach taken and demonstrate the benefits that are achievable. This paper will focus on the role of blasting in the optimisation of the entire mine to mill process chain and discuss elements of the PIO methodology: rock characterisation, fragmentation modelling and measurement, the relationship between fragmentation and mill throughput and material tracking.

Jan 1, 2007