Search Documents

The karst water system in Han-Xing District is charaterised by heterogeneity in karstification and permeability of the limestone aquifer, unsteady flowing of the groundwater along karst runoff zone system, periodic recharge related with the periodic precipitation, and concentrative discharge of the groundwater in the form of karstic spring groups. The basic law is that the quantity of the water is very large during waterflood period and rather small in dry period, which has brought about difficulties and contradictions in mining and water supply. The measure to bring the karst water under control must be based on the principle of comprehensive ways and on the systems engineering method. Macroscopiclly, it is the reasonable countermeasure to retain surface water in the upstream section of the karst water system and to strengthen infiltration in the midstream section and to combine exploitation and utilization of the groundwater with water protection and mine dewatering in the area in which mines are distributed.

Jan 1, 1988

IT is intended herein: to make some brief comments on geophysical 'work in general and on the various methods, and then to refer to that branch which, perhaps, is of the greatest importance and interest to the metalliferous mining engineer, i.e., the variousmethods of electrical prospecting.The term geophysics was originally applied to those larger physical and geodetic studies and methods concerned with such purely scientific subjects as the investigation of the true figure of the earth and the determination of the stability relations resultingtherefrom. Applied geophysics and geophysical methods of prospecting are concerned primarily with the search for, and investigation of, useful mineral deposits concealed within the earth's crust and not readily detectable by the normal methods employed bythe mining geologist and prospector. The methods employed have been devised as a result of co-operation between mining men, geologists, and physicists, and, although steady progress has been made during the past 20 years or so, it is within the last four orfive years that the importance of these methods has been acknowledged by the mining world in general. Although many of these methods are still in, or have barely emerged from, the experimental stages, a steadily increasing list of important discoveries is attributable to their employment-more particularly in Europe and America than elsewhere. The various methods have each their own limitations regarding the class of work they can undertake, and no one method is capable of general application. The greatest care should be exercised in selecting the method, or methods, to be employed in any particular area, the...

Jan 1, 1928

By S Morrell, D Clark

æMine to MillÆ improvement involves optimising the chain of rock breakage processes from the in situ rock in the mine to the output of the concentrator. A growing number of paper studies and case histories from metalliferous mines (AusIMM, 1998; JKMRC, 1998; Clark and Scott, 2002) demonstrate that generating more breakage in the pit and the primary crusher can lead to benefits to milling that result in significant improvements to the economic performance of a mining project. However, unless the ævalueÆ of doing this (benefit over cost?) can be appropriately quantified, the approach cannot be effectively managed and the increases in blasting and monitoring costs cannot be justified.Mining operations have traditionally been organised into the separate departments of geology, mining and processing based on the specialist skills required and the different professional disciplines involved. Process optimisation across these boundaries has commonly been frustrated by management requirements to minimise the costs incurred by each department without adequate reference to the ævalueÆ being created. Companies have tended to discard positions that provide a technical over-view of the value chain, reducing the number of people with the opportunity to influence practices across these process boundaries.This paper discusses these issues and identifies measures required to quantify and manage the ævalueÆ provided by æMine to MillÆ improvement generated by the intense blasting of ore.

Jan 1, 2002

An established method exists for the computation of rope lifetimes for shaft hoisting applications in the mining industry. In an earlier study, during the 1990s, an initial comparison of the calculated and actual rope life for various types of hoisting plants showed reasonably good correlation. In the meantime the calculation method has been developed further. The rotation behaviour of the rope during hoisting and the effects of multilayer spooling on drums are now considered in the assessment of expected rope lifetimes. The ability to determine an estimate of rope life in advance is particularly useful for mining companies. Such analysis allows them to predict the effects of rope choice in their particular application and thereby reduce the total cost of rope ownership. Such calculation techniques also allow designers of winding plants to identify aspects of the hoisting configuration that may negatively affect rope life. Often small (low-cost) changes, like increasing the diameter of head sheaves, can result in considerable improvements in rope performance. This paper describes the extended lifetime calculation method and gives further examples of the comparison between actual and calculated rope lives for operational double-drum mine hoists.

Jan 1, 2005

The truly scientific method in the study of such questions at the present day is the reverse of that which was followed in the early days of geology, when after the observation of a few isolated facts, some great geological mind was led to a general theory, and humbler followers were only too apt to do mild violence to nature in order to make her facts conform to it tt accumulates year after year a multitude of facts of patient observation, supported by studies with the microscope, and in the laboratory, avoiding general theories, and only making such deductions in regard to locftl conditions as are supported by the overwhelming evidence of facts. S. F. Emmons, on the geological distribution of minerals in the United States, at the "world's congress" of mining engineers, Chicago. Fig. l.-This exhibits the general stratigraphical characters of the southern lodes. The" Indicator" veins, the great barren lode masses, a later fissure than all of these (" B "), and the auriferous lodes of last series cleaving the wrinkled terraces and the older lodes also are" Indicator" veins. B is a later formed vein that leaves no " depositions" behind. ooe are fragments of the" most ancient'' lode wreckage. Db are the auriferous lodes and correspond with those lodes, also whose auriferous characters are not result of secondary impregnations.

By R McConnochie, J V. Rowland, J L. Mauk

The Sovereign prospect in the lower Waitekauri Valley of the southern Hauraki Goldfield occurs in daciterhyolite flows and volcanic breccias of the Waipupu Formation. The lower Waitekauri Valley contains a series of NE to NNE-trending normal faults, and the Sovereign prospect lies in a NW-striking graben. The structure of the Sovereign prospect is complex. NE to NNE-trending veins and normal faults dominate the area, however WWNW and N to S-trending structures occur locally. Kinematic analysis of these structures indicates predominantly dip-slip movement, with a local strike-slip component. At least two sets of veins occur in the area: 1.        steeply dipping veins; and 2.       low angle veins, which cross-cut and locally offset the steeper dipping        vein set. Mineralization appears to have formed during normal faulting in an extensional regime.

Jan 1, 2007

By A Califice, E Pirard, M Benzaazoua, R Mermillod-Blondin

Image analysis is more and more considered as a powerful tool for quantitative analysis of ores and concentrates. Apart from being very much dependent upon the quality of the imaging principle and the adequacy of the imaging sensor, quantitative image analysis is also the result of a long chain of material, image and pixel sampling strategies. The most reliable way to demonstrate the accuracy and the precision of modal analysis obtained from images is probably to use a blended material with known proportions of pure minerals and confront the results obtained from different analytical tools. This operation has been performed on a series of mineral blends mimicking the tailings of a flotation operation in a plant operating on massive sulfide mineralisation. The intention was to be able to better predict acid mine drainage potential from direct mineralogical observations. Selected sulfide minerals: pyrite (Py), pyrrhotite (Po), chalcopyrite (Cp) and sphalerite (Sp) were mixed as variable amounts within gangue minerals (quartz, calcite, dolomite and siderite). Typical blends contained six to ten per cent (Py); one to three per cent (Po); 0.5 to one per cent (Cp, Sp); 15 to 40 per cent carbonates and 40 to 75 per cent quartz by mass. The 1000 gram blends were carefully sampled and prepared for X-ray diffraction, chemical analysis by ICP-AES and optical microscopy image analysis (OMIA). Results obtained for the different analytical techniques are compared and discussed revealing the limits and strength of each method in the accurate quantification of sulfide and gangue minerals.

Jan 1, 2008

In the retreatment of an old tailing dump containing five per cent of lead principally as lead sulphate, the lead sulphate was floated with liquid Aerofloat reagent after sulphidising with phosphorous pentasulphide in an acid circuit. A zinc middling product was removed by flotation before recovering the lead. Concentrate products were sundried in surface dams.INTRODUCTIONDuring the period between 1917 and 1928 the Junction North Broken Hill Mine N.L. deposited several tailing dumps on its leases, which were acquired by North Broken Hill Ltd.in 1931. One of these dumps lay alongside a main road close to a residential area. The high metal prices prevailing in the post-war years (1945 onwards) provided a strong incentive for retreating this dump and transferring it to a less objectionable site.SAMPLING AND TESTINGIn 1946 a sampling and testing campaign was instituted which culminated in 1949 in a decision being made to erect a tailing retreatment plant adjacent to the dump.The dump was sampled with a 3 in. post hole auger using extension lengths of -! in. pipe for drilling to 30 ft. The dump material was fine and moist and core recovery was excellent. Hole depths ranged from 14 ft. to 30 ft., with an average dump depth of 20 ft.Individual samples were prepared from successive 9 ft.lengths of core and each sample thus obtained was, submitted for sizing and assay.The sampling showed that the dump contained approximately 380,000 tons of fine tailing assaying:

Jan 1, 1956

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fi xed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user: to develop a technical model for conceptualised conveyor systems, to perform economic analysis on the developed technical model, and to conduct a comparative and risk analysis. An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help fi les as well as the use of familiar graphical user interface elements such as the MS Offi ce 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

In current mining practices it is desirable to bring about a substantial increase in both rate of face advance and productivity, thus compelling the mine engineer to consider better and more productive ways of mining. Transportation plays a vital role in achieving improved productivity. This paper focuses on horizontal transportation systems. Horizontal transportation is defined from the shaft station area to the end of the stope cross-cut. Traditionally, horizontal transportation is inefficient in comparison to vertical transportation efficiencies and accounts for a high proportion of South African mine accidents. Thus, the role of horizontal transportation has been investigated in detail, as it offers the greatest chance for improvement. The purpose of the paper is to provide a best practice guideline for the design of horizontal underground transport systems. It is intended that the document be used by mine designers and planners as an aide memoir during the design process and benefit may well be gained from retrofit and reorganisation activity. The paper looks at transport systems suitable for deep level gold mining in South Africa and evaluates such items as management, scheduling, and haulage systems. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2003

By F Cesnik, P Griffin, S Green

In July 2004 a flotation concentrate regrind circuit was commissioned in the æHigh GradeÆ Ridgeway concentrator at NewcrestÆs Cadia Valley Operations. This was the culmination of two years of project testing, process design and planning which commenced shortly after commissioning the concentrator in March 2002. During the two-year project evolution alternative grinding technologies were evaluated from conventional ball milling through to sand milling. A Detritor mill was eventually selected for the duty and the criteria on which this selection was based will be presented. As the project evolved so too did the equipment sizing with the concentrator quickly exceeding design capacity of 4 Mtpa and currently averaging 5.6 Mtpa, the process design had to accommodate this and future potential throughput increases. This paper will focus on the supporting testwork, circuit surveys and concentrate properties which were used as the design basis for the project. The economic evaluation which led to the project receiving board approval in November 2003 will also be presented. Detailed design and construction management issues will be discussed as will preliminary results and findings up to November 2004.

Jan 1, 2005

By Giannini L. M

Optimisation techniques, based on the block model, for solving the optimum pit limit problem were discussed in an earlier paper. Of the available techniques the one based on graph theory proved to be the most attractive. In the graph theory model the vertices represent blocks and the arcs represent the mining restrictions. For large ore-bodies direct application of the graph theory method poses considerable computational and storage problems. Techniques for easing the computational effort by reducingthe problem size were introduced in an earlier paper. Further, significant computational savings can be made by exploiting the structure of the graph. This is done by building the graph up level by level and successively applying the graph theory algorithm to reduce the number of blocks. In building up the graph in this way one needs what is called a "search pattern" to indicate which arcs are to be added as new vertices are introduced. Moreover, as it is essential to keep the number of arcs to a minimum it is necessary to establish a "minimum search pattern".The problem of determining minimum search patterns for any block model and for any wall slope restrictions has not been considered in the literature.The objective of this paper is to present a complete solution to this problem and to discuss, through typical case studies, the application of the associated software developed.

Jan 1, 1988

By B R. Bittencourt, D A. B Pasin, D Pi

Three main genetic types of hematite can be recognised at Quadrilßtero Ferrffero (QF): Micaceous or schistose hematite derived by metamorphic/metasomatic process during regional metamorphism, increasing eastward, formed under temperatures ranging from 250¦C to 500¦C in CO2-rich aqueous carbonic, high- to medium-salinity fluids. Hematite in shear and mylonite zones, showing a wide variation of fluid and temperature conditions, between metamorphic and hydrothermal conditions. Deformed quartz-specular hematite veins formed during the late phases. Hydrothermal, compact and isotropic hematite developed during a brittle-ductile regime, forming the cement of the boudinage-kink breccia and jacutinga-type of gold mineralisation, under temperatures ranging from 80¦C to 140¦C in aqueous, low- to medium salinity, oxidant fluids, resulting from the interaction of meteoric and metamorphic/metasomatic fluids. Quartz-carbonate-sulfide veins were formed slightly later, through reducing fluids.

Jan 1, 2005

By K-S Kim, C-Y Kim, D-G Kim

In tunnel construction or other underground construction, a detailed knowledge of the rock mass ahead of the face is essential for both safety and efficiency of work. Many tunnel collapses have been reported to occur because of lack of appropriate information, such as the geological conditions ahead of the tunnel face. One of the methods which can identify rock mass conditions is the application of drill monitoring data obtained from blasting drill holes, which can detect abrupt and unexpected changes in ground conditions, geological structure and the mechanical and physical properties of rock mass. This paper presents a new approach to how drill performance parameters can be used for prediction of geological conditions ahead of tunnel face. The predictions are based on monitoring the drill parameters of instantaneous advance speed, torque and tool pressure. In order to assess conditions ahead of tunnel face, tunnel seismic profiling (TSP) and a horizontal boring investigation were undertaken and the obtained data compared to the drilling data. The predicted results using drilling performance parameters correlated well with geological conditions ahead of tunnel face.

Jan 1, 2008

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is anenergy efficient way of grinding and a number of operations haveutilised this in the design of their comminution circuits. Owing tothe large flow of slurry through the mill that results fromoperating this way the grates and pulp lifters have to be designedto cope. However, the literature has little or no information onhow grate and pulp lifter size and design are related to theirability to remove slurry from the mill. Over the last few years theJKMRC has been researching this area and has developedrelationships between grate/pulp lifter design and flowratecapacity. At the same time it has determined the major causes ofpulp lifter inefficiency and a solution to preventing thisinefficiency (the Twin Chamber Pulp Lifter). This paperdescribes the models that have been developed through thisprogram and uses industrial scale data to illustrate their accuracy.Results from the industrial trials of the Twin Chamber PulpLifter are also presented.

Jan 1, 2001

This paper is intended to continue the subject in the light of recent work, from where it was left at the conclusion of the discussion on the excellent paper by the late Mr. Noel Haszard. The position then obtaining is briefly summarised below:-The points which received general agreement at that time were:-'(1) That the gold occurs, probably in an elemental form, in a state of very fine division in the pyrite.(2) That the aim in roasting of Kalgoorlie flotation concentrates should be to obtain the maximum porosity possible. The gold tellurides were amenable to treatment with either a' solution of high lime and cyanide strength combined with fine grinding, or bybromocyanidation without re-grinding.(3) That a low roasting temperature is essential during the elimination of the first atom of sulphur, if the final calcine is to give a good extraction by cyanidation.(4) Even with the best temperature conditions of roasting then determined, and after a period of cyanidation of the calcines until no further extraction was obtainable, the lowest calcine residues obtainable were equivalent to approximately 1·8 dwts. per long ton, based on an original concentrate of pure pyrite.There was some division of opinion at the time as to whether the temperature of the later stages of roasting was significant, and also as to the reason why the initial roasting temperatures had so marked an effect.

Jan 1, 1939

By C M. Hill

This paper aims to provide a brief overview of the Australian Coal Bed Methane (CBM) industry and more importantly the challenges to sustainable management of the industryÆs by-product, groundwater. In a country where water is scarce and having gone through one of the worst recorded droughts it is vital that this important industry be seen to be managing water in a responsible manner with the greatest environmental and social benefit. Benefits of the water from CBM wells can be enhanced through treatment to produce potable water for domestic or stock purposes, water for irrigation or aquaculture or lower quality or untreated water for industrial or mining purposes. Other options are re-injection of raw water or waste from the treatment processes or discharge to surface waterways. The critical change and difference between CBM projects and traditional oil and gas operations should be that where possible water is no longer disposed of via evaporation ponds with the dual legacy of waste of the water resource and an environmental contamination problem with the remaining salt and brine product.

Jan 1, 2003

By S Paciornik

The traditional trading of iron ores is based on chemical specifications and particle size distribution. However, recent characterisation studies, that bring additional information like mineralogical composition and microstructural (textural) aspects, have become important. They contribute to determination of the iron ores downstream beneficiation operations and subsequent steelmaking processing, allowing improvements on both new and existing processes. Despite progress in commercial scanning electron microscope/energy dispersive spectrometer (SEM/EDS) automatic instruments in the last decade, these systems are not capable of performing the identification and discrimination of major iron ore minerals (haematite and magnetite) and the consequent description of its microstructure. On the other hand, reflected light microscopy (RLM) can easily distinguish the iron oxides by their reflectancies, but it cannot discriminate quartz and epoxy resin, which present similar colour on images. The present work proposes an innovative method to perform a quantitative mineralogy characterisation of iron ore based on RLM-SEM co-site microscopy. This technique combines images obtained by RLM and SEM through an automatic registration procedure that accurately aligns the two kinds of images of each field. In fact, it creates multi-dimensional images, which are then analysed using image processing and pattern recognition techniques. The case study is an itabiritic iron ore from Quadrilßtero Ferrffero (Brazil) which contains mainly quartz, goethite, magnetite and haematite. The discrimination of phases that are not distinguishable with either RLM (epoxy resin and quartz) or SEM (haematite and magnetite) can be performed through this multimodal approach, allowing the subsequent mineralogical quantification. The mineralogical quantification computed by image analysis was consistent with independently obtained results based on the Rietveld technique.

Jan 1, 2008

During October 1947 an Authority to Prospect was granted by the Minister of Mines to lVIount Isa Mines Limited over an area of approximately 75 sq. miles to the north of Mount Isa.Application for the Authority to Prospect had been made after Zinc Corporation Limited had been granted prospecting rights over two areas, one of 1,265 acres immediately to the north of the Mount Isa Mines leases and the other of 1,960 acres adjoining the south end of Mount Isa Mines leases.METHODSAs a means of providing a cheap map of sufficient accuracy on which to plot geological features, both Mount Isa Mines Limited and Zinc Corporation Limited agreed upon aerial photographs and the two companies shared the cost of an aerial photographic survey by Adastra Airways of 130 sq. miles which covered the prospecting areas held by both companies.The photographs were on a scale of 800 ft. to I in. with 60% overlap on the north-south runs and 25% overlap east-west. A set of alternate prints enlarged to 400 ft. to 1 \in. were obtained for field work. The 400 ft. to 1 in. scale unglossed photographs (size 18 in. x 18 in.) were taken On to the field and rock outcrops, and uncorrelated structures were plotted directly on to them in red crayon pencil. The geological observations were then transferred in the office to a tracing on which accuracy of azimuth and scale was controlled by use of a photo mosaic and ground surveys.

Jan 1, 1953

By Gillies A. D S, Lee A. H

The major operational objectives of a mine water resource management system (WRMS) are to supply the water needs of the mine and mill, to minimise disturbance to mining due to rainfall flooding or seepage and to dispose of excess water. Historically, company management have placed a significantly lower emphasis on managing the WRMS as compared to managing production. Changing Government legislation concerned with the disposal of water from mine sites is, in many cases making mining companies look more closely at how they manage their water. For example, within the next few years it is likely that prior to mining approval by the Government, mining operations will have to submit water management plans/budgets and contingency strategies in addition to operational plans. While the formulation of a comprehensive water management plan/budget is an additional cost to the company at the mine establishment stage, such plans can be beneficial to the operation in the longer term.The two keys for the efficient design, operation and development of a WRMS are the establishment of written goals which have managerial priority and secondly, access to appropriate good quality data. Managerial priority towards the WRMS will increase as a consequence of the education of mine operators in the benefits to the operation of good WRMS management or less desirably as a requirement to meet Government legislation. The collection of appropriate WRMS data is a more complex issue and to obtain information efficiently and cost effectively relies on the clear definition of the data application.

Jan 1, 1992