Search Documents

Bahuerachi Project Characteristics Why it?s nicer at Bahuerachi Mexico is a mining country Low political, regulatory and trade risk Low social/permitting risk Proximity to infrastructure Road Power grid (8 km) Rail line (25 km) High grade zones (skarns), CRD and near surface oxide component are sweet spots to the overall system. Size of low grade system points to potential long mine life?and numerous new targets developing. Timelines-2006? 90 to 100 combined RC and core holes to go! MAIN ZONE Drilling ? Goat ?Finish Mid April ? Main Zone, going North, depth of testing dependent, estimated for May ? North Lobe-May ? Commission independent resource estimate by May 06 for results of first pass drilling to date ?tonnesand grades ?Main Zone Milestone. ? Continue infill or expanded drilling to July (minimum) ? 1stpass RC scheduled until September OTHER Targets ? Begin drill testing North Skarn target Mid-April, minimum 5 drill holes, 1,000 meters. Ongoing expansion of target with surface work (mapping) ? Road to Colome(Skarnin north of Main Zone) as part of porphyry program ? Tule(southern) porphyry and skarn system-soils and mapping OUTSTANDING events Metallurgical report on floating and leaching tests (Sulphide/oxides).

May 1, 2006

?Four-wheel, skid-steer, rover developed for CSA ?U-chassis for payload accommodation ?Passive geometric suspension ?Max speed 13km/hr ?Remote workstation ?275kg payload capacity ?On-board processor, IMU, motor encoders ?5.2kW-h battery capacity

May 1, 2013

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By J. E. Gill

Introduction During the past summer, detailed geological mapping was extended to cover the entire group of 31 claims owned by Waite-Ackerman-Montgomery Mines, Ltd., and considerable new information was revealed by development and exploratory work underground. These new facts provide a more complete view of the lithology and structure of the area than has heretofore been available. They also necessitate revision of certain interpretations presented last year by Peale (l), and have served to straighten out some of the problems suggested by Porritt (2). The purpose of this paper is to outline in a broad way the relations as now understood and to discuss in detail certain points which should be of interest to members of the Institute. Maps and records by the mine staff have been freely used in arriving at the interpretation presented in the following pages. The writers are especially indebted to Mr. R. V. Porritt, the mine manager, with whom many of the problems touched upon were discussed on the ground and whose intimate knowledge of the geology of the underground workings aided greatly in testing various hypotheses. The writers have profited greatly, also, from close association with Dr. W. F. James during the course of the work. Permission to publish the included data has very kindly been given .by the management.

Jan 1, 1932

By R. Lovat, J. A. Hunter

"The design, development, and verification of the Lovat 7.6metre diameter full-face tunnel-boring machine is reviewed. Programmatic and technical challenges are outlined with a review of the specifications and the design to meet these requirements. Subsystem designs are presented for the waste material removal, ventilation, cutter head, structural support, advance technique, water removal, and interfaces with the Donkin-Morien Mine. The techniques used to verify that the design meets the requirements is by testing in the Lovat factory and in the field. Certification of the machine for use in a methane environment is discussed.IntroductionStudies have concluded that the average annual worldwide tunnel construction is 500 kilometres at an estimated average co st of $3,400 U.S . per linear metre. The total market value of the tunnelling industry is estimated as approximately $1.7 billion U.S. per annum. Of this, the current market for tunnelboring machine excavation is approximately $270 million U.S. per annum worldwide with a further potential of $250 million if more contractors are convinced that Tunnel-Boring Machines (TBM) are more suitable than conventional techniques. The worldwide civil tunnelling market has the potential to double each year in the next 5 to 15 years. Growth has been identified in the energy and mineral resources sectors of the economies of many nations and a significant volume of machine tunnelling studies and trials are presently underway for the extraction of coal, uranium , heavy oil or oil sand fuels, metallic and non-metallic industrial minerals and base metal or rare earth ores. Further tunnel projects for regional transportation, waterpower, irrigation , high density urban transportation, storm water sewers and water supply purposes are continually being implemented with new concepts like military security facilities and underground storage schemes being considered.Lo vat Tunnel Equipment of Rexdale, Ontario, the only Canadian manufacturer of TBMs was incorporated in 1973 to manufacture so ft ground tunnel-boring machines to satisfy this growing market demand. Lovat has produced an average of 5 machines per annum during the period 1972 - 1982 and has established an international reputation for competitive costs, quality of construction, after-sales service, and reliability. As of June 1982 Lovat TBM's have been used to tunnel over 240 km in projects throughout the world."

Jan 1, 1984

By I. Thobadi, C. Pawlik, K. Bisaka, S. Mokoena, M. Erwee

The PyEarth™ process developed at Mintek has been demonstrated successfully at pilot scale. Nine tons of ore containing 2.3 mass % of total rare earth oxides (TREO) from a dormant mineralogically complex iron-rich ore deposit, was subjected to a concentrating smelting step in a 200 kW DC open-arc pilot furnace and the rare earths from the resulting slag were extracted via a hydrometallurgical route. This ore deposit is practically not amenable to extraction by conventional methods. The testwork results proved that the PyEarth™ process was able to optimize the extraction of rare earths while minimizing waste through the removal of iron as a saleable iron alloy. Reduction of iron to the alloy in the smelting step was found flexible, efficient, and controllable, while rare earths were left virtually unreduced in the slag phase. The slag chemistry is selected to optimize both the smelting and leaching performances as well as the alloy composition. Leaching of the resulting slag was found possible and most efficient in hydrochloric acid amongst other lixiviants tested.

Jan 1, 2017

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By Dale Scott

"The Aggregate Resources Inventory Program was initiated 10 produce reports which assess the aggregate resources of municipalities designated under the Pits and Quarries Control ACI, 1971.Each report consists of three copies accompanied by a text. The text describes the local mineral aggregate resources, extractive activity and characteristics of the ""Selected Deposits"". The first map shows the known sand and gravel resources and their quality. The second map indicates selected sand and gravel resources of primary, secondary and tertiary significance. The third map indicates both bedrock resources and bedrock areas suitable f or extraction. These maps and the text are prepared in a formal suited for use by planning personnel.Recently, the Aggregate Resources Inventory Program has undergone evolutionary changes. New sources of data are being utilized in the inventory reports; in particular, detailed field assessment by inspecting, sampling, drilling and backhoe pitting. Liaison and joint assessment with district and regional Mineral Resources staff of the Ministry of Natural Resources, and personnel of the Ministry of Transportation and Communications, are key components of the Program.Twenty-two reports were available to the public as of December 1980, with a further thirty-six awaiting publication. Our present production rate is 3.5 reports per month. The reports appear to be well accepted by the municipalities and have proven effective in conserving prime aggregate resource areas.IntroductionThe urbanization of Southern Ontario has resulted in a major increase in the production of industrial minerals, such as sand, gravel, clay, shale, gypsum and stone, for use as cru shed aggregate, building stone, lime and cement.Although mineral aggregate deposits are plentiful in Southern Ontario, they are fixed-location, non-renewable resources. The potential for extractive development is usually greatest in urban fringe areas where land-use competition is extreme. Comprehensive planning and resource management strategies are required to make the best use of available resources, especially in those areas experiencing rapid development. Such strategies must be based on a sound knowledge of the total mineral aggregate resource base at both local and regional levels."

Jan 1, 1982

By Dale Scott

"The Aggregate Resources Inventory Program was initiated 10 produce reports which assess the aggregate resources of municipalities designated under the Pits and Quarries Control ACI, 1971.Each report consists of three copies accompanied by a text. The text describes the local mineral aggregate resources, extractive activity and characteristics of the ""Selected Deposits"". The first map shows the known sand and gravel resources and their quality. The second map indicates selected sand and gravel resources of primary, secondary and tertiary significance. The third map indicates both bedrock resources and bedrock areas suitable f or extraction. These maps and the text are prepared in a formal suited for use by planning personnel.Recently, the Aggregate Resources Inventory Program has undergone evolutionary changes. New sources of data are being utilized in the inventory reports; in particular, detailed field assessment by inspecting, sampling, drilling and backhoe pitting. Liaison and joint assessment with district and regional Mineral Resources staff of the Ministry of Natural Resources, and personnel of the Ministry of Transportation and Communications, are key components of the Program.Twenty-two reports were available to the public as of December 1980, with a further thirty-six awaiting publication. Our present production rate is 3.5 reports per month. The reports appear to be well accepted by the municipalities and have proven effective in conserving prime aggregate resource areas.IntroductionThe urbanization of Southern Ontario has resulted in a major increase in the production of industrial minerals, such as sand, gravel, clay, shale, gypsum and stone, for use as cru shed aggregate, building stone, lime and cement.Although mineral aggregate deposits are plentiful in Southern Ontario, they are fixed-location, non-renewable resources. The potential for extractive development is usually greatest in urban fringe areas where land-use competition is extreme. Comprehensive planning and resource management strategies are required to make the best use of available resources, especially in those areas experiencing rapid development. Such strategies must be based on a sound knowledge of the total mineral aggregate resource base at both local and regional levels."

Jan 1, 1982

By Thomas G. Madgwick

Introduction Development of oil and gas is still centred in the Province of Alberta, much as it was when C. C. Ross read a paper on this subject three years ago at the Annual General Meeting in Montreal; but so far as gas is concerned, its early production in Saskatchewan seems now assured. The three years that have elapsed since Mr. Ross' paper have witnessed a growth in the world's production of oil that has created a potential supply out of all proportion to the demand for petroleum products, and one that has resisted the most energetic efforts of the industry entirely to control. The natural result has been very much to retard the active prospecting of new structures in the Prairie Provinces with any immediate view to oil production, although the same factor has not hindered the search for gas to the same extent. One consequence has been to divert the attention of organized oil operators from wildcat drilling to more detailed geological investigation than had hitherto been customary, sometimes accompanied by test drilling with a view to the elucidation of geological structure rather than to the immediate development of production which at the present is not needed. Nevertheless, in spite of the growth of this phase of oil prospecting - which the writer would be the last not to welcome as a very real blessing and of far greater value than indiscriminate wildcat drilling in either the complex structures of the foothills or the simpler but largely concealed formations of the plains- it is most satisfactory to have to record that in these three years the growth of production both of naphtha and the heavier crude-oil has kept pace with the by no means inconsiderable growth in the production and utilization of natural gas.

Jan 1, 1929

By H. J. White

Haynes International, a world leader in the manufacture and production of nickel, and cobalt base alloys has invented and developed a low cost high temperature material, with a unique combination of superior oxidation resistance and weldability/ fabricability. HAYNES® HR-224TM (Ni ? 27.5Fe ? 20Cr ?3.8A1 ? 0.3Si ? 0.3Ti) forms a planar/ continuous/ adherent aluminum oxide film at high temperatures which has been shown to effectively limit chromium poisoning in solid oxide fuel, cell, systems. A 20,000 pound vacuum induction melted (VIM) + electroslag remelted (ESR) heat has been melted and converted into various product forms: sheet, plate, bar, welded tubing, wire, etc. The alloy was designed for service in severely oxidizing environments recuperators, automotive catalytic converters, wire strand annealing furnace tubes, etc. and has been of great interest to solid oxide fuel, cell, manufacturers as a materials of construction in balance of plant (BOP) design. This manuscript presents the physical, properties, mechanica, properties, and oxidation resistance of the alloy compared to other materials being considered for solid oxide fuel, cell, design

Jan 1, 2010

By C. J. Cajka

Commodity agreements, trade liberalization, producer cartels, the New International Economic Order, price stabilization and access to supply are buzz words of the day. The international concern and dialogue on these concepts, often by a new breed of politically motivated experts, have generated intense interest in seeking an international solution to natural resource problems. While this momentum was maintained during the past year, the growing incidence of protectionist actions by several major nations has been eroding confidence in the global approach. The seriousness of current difficulties has created an urgent need for decisive action. At the same time, the limitations of the global approach have become more evident.

Jan 1, 1978

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By Ken Wood, Luc Duval

"The development and operation of the milling circuits treating the different Selbaie orebodies are discussed in this paper. The project is reviewed from metallurgical evaluation through construction to present operating status. The current flowsheets are described, with discussion of some unusual features.IntroductionThe Selbaie concentrator commenced initial production in August 1981, treating underground B zone copper ore in a single 1500 t/d circuit. Throughput was increased to 1650 t/d in 1985. The mill was expanded in 1986 to treat ore from the A-I zone open pit; an independent circuit was added to selectively treat 5000 t/d of copper-zinc ore. Current total mill throughput through both circuits averages 7200 t/d with the production of approximately 270 t/d of copper concentrate and 230 t/d of zinc concentrate.This paper describes the stages involved in bringing the project from initial laboratory testing to its current status as one of the most important producers of silver, copper and zinc in Quebec and a major employer in the region."

Jan 1, 1990

Agenda ? Where?s Victor ? What work was done to get approval to spend $982m ? a brief history ? Some project facts ? The triple bottom-line accomplishments to date ? Construction A Brief History of Victor ? 1960?s ? first sampling in area ? 1980?s ? stream samples and Victor kimberlite discovered ? 1990?s ? test / bulk samples ? 1999 / 2000 ? large bulk samples ? 2000 / 2003 ? technical evaluation through to Feasibility Study, permitting process

May 1, 2006

By G. Gabra

"A process of leaching niobium oxide from pyrochlore concentrate using hydrofluoric acid is described. Variables such as acid concentration, temperature, reaction time, solid/acid ratio, agitation speed and particle size are correlated to the recovery of niobium oxide.The relatively low activation energy (1,86 Kcal/mole) and the dependence of reaction rate on agitation suggest that the process is diffusion controlled. The optimum conditions for extracting niobium oxide from the leach solution, using either methyl isobutyl ketone or tributyl phosphate have been determined.IntroductionMost of the commercial production of niobium and tantalum has been derived from the treatment of columbite - tantalite minerals.In recent years (1960) , pyrochlore mineral has been found to be an alternate source of niobium . This mineral varies widely in composition and contains in addition to the main elements of calcium , sodium and niobium, some tantalum, fluorine, rare earth elements, titanium, alkali an d alkaline earth elements.It is well known that the province of Quebec possesses several pyrochlore niobium deposits totalling approximately 151 million ton s at an average 0.45% niobium oxide(1). One of the deposits, the St-Honor carbonatite, was brought into production by Niobec Inc. in 1976. Flotation o f this material produces a concentrate of about 60% Nb205(2).In view of an expanding niobium market in recent years and the presence of large niobium deposits in the province, a research and development program was initiated at the Centre de Recherches Miner ales to evaluate known processes for the separation of niobium and tantalum from each other as well as their purification . Some work has also been undertaken at the CRM to develop an improved extraction process. T his work will be the subject of further communication s."

Jan 1, 1985

By R. F. Robertson

"Adsorption isotherms of hexyl mercaptan vapour on synthetic sphalerite, zinc sulphide and zinc oxide were de-termined with a gravimetric McBain-Baker micro balance incorporated in the B.E.T. apparatus. Isotherms are given for hexyl mercaptan on synthetic sphalerite at 25°C, 0.5°C and 50°C; on zinc sulphide at 25°C and 1.5°C; and on zinc oxide at 25°C. All these isotherms are sigmoidal, with a definite change in slope at or close to the mono-layer. The amount of mercaptan adsorbed below the monolayer increases almost linearly with relative pressure to P/P0 = 0.8.Above this value, the amount adsorbed increases very rapidly with relative pressure. Hysteresis loops appear in the isotherms for all adsorption-desorption cycles. These loops are completely reversible. It is not possible to desorb the mercaptan monolayer from any of the adsorbents, even at elevated temperatures."

Jan 1, 1966

By H. Saeedi Ali, A. J. Monhemius

"Anglo Asian Mining’s Gedabek mine is situated in the Lesser Caucasus mountains in Western Azerbaijan. The ore body is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold and copper-bearing ores. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions. Ore processing at Gedabek is by agitation leaching for high grade ore (>1g Au/t) and heap leaching for lower grade ore. In order to cope with the high copper concentrations in the cyanide leach liquors, a unique combination of resin-in-pulp for selective gold extraction and SART processing for copper removal and cyanide recovery is used. In 2015, a flotation plant was added to treat the tailings from the agitation leach plant before the tails are sent to the tailings dam. This plant produces a copper sulphide flotation concentrate and also recovers some of the residual gold and silver in the tailings. Since February 2017, due to lower grades of gold and higher copper in the feed ore, the decision was taken to alter the flow sheet and to carry out flotation ahead of agitation leaching, to reduce the cyanide consumption during leaching by removing soluble copper minerals. The paper compares and contrasts the performance of the plant in the two configurations, namely, (i) leaching followed by flotation and (ii) flotation followed by leaching.INTRODUCTION In May 2009, Anglo Asian Mining started open pit mining for gold on its Gedabek property in the Lesser Caucasus Mountains in western Azerbaijan. Gedabek is situated on the highly mineralized Tethyan Belt that runs from the Himalayas to the Balkans. The ore body at Gedabek is a complex copper-gold porphyry deposit, comprising intermixed oxidized, transition and sulphidic gold-bearing ores. The sulphidic ores contain mainly pyrite and chalcopyrite, with some secondary copper sulphide minerals, such as bornite and chalcocite, and minor amounts of sphalerite, galena and tetrahedrite. Gold in the sulphide ores is generally not refractory and is recoverable by cyanide leaching, but the secondary copper minerals, which are also cyanide soluble, lead to high cyanide consumptions and passivation of free gold."

Jan 1, 2017

By O. Mejia

"As study was undertaken to investigate the relationship between mill liner wear and grinding energy efficiency and to assess the opportunity to control mill speed to improve energy performance as mill liner wears. The study involved analysis of plant operating data and liner wear profiles over time. The operating work index was found to be an effective tool to identify the decrease of grinding efficiency along the liner service. The plant data show that the mill grinding efficiency as determined by monitoring the operating work index, and throughput decreases as liner wears. However, efficiency and throughput can be maintained by either changing the liner more frequently or by increasing the mill speed. Two scenarios for increasing mill throughput were analyzed. The first one involves changing the liner before the efficiency drops and the second one requires increasing the mill speed from 75% to 79%. Both scenarios show financial benefits that can be used in mill operations.INTRODUCTION The analysis of the mill power draw is used in this study as a key parameter for comparing mill liner profile and its effect on mill performance. Current technology and simulation software used in the mining industry do not factor in the impact of liner wear profiles in grinding efficiency and mill throughput (Toor, 2013). To address this gap, this study provides an analysis of key factors affecting mill throughput and grinding efficiency: mill speed, ball loading, and liner profiles. Several years of plant mill operating data, published research papers, and MillTraj® simulation results are used to demonstrate that face angles impact grinding efficiency and throughput and that mill speed can be used to overcome this problem. Moreover, the liner profile wear analyses clarify a mismatch between actual and estimated power draw calculations."

Jan 1, 2019