Search Documents

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Mines Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840 µm to 1200 µm in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding , smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840 µm to 1200 µm class reported to the 600 µm to 840 µm; this figure is much higher than for silica (46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50 urn to JOO pm to 20 at 500 um to 1000µm.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840 µm to 1200 µm to the 600 µm to 840 µm class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photograhic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase over-all gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydro cyclones takes place at a much finer cut-size than ore, 20 µm vs 57 µm. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty-four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3 in.) Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89% and 92% for the PCUF and secondary mill discharge."

Jan 1, 1991

By Steve McMullan, Blaine Webster, Ian Johnson, Ron Matthews

"Time domain spectral Induced Polarization (IP) data from the Tower, Jojay and Laurel Lake gold deposits in northern Saskatchewan are presented. The resistivity data shows both resistivity lows (due to fault, shear or alteration zones) and resistivity highs (due to silicification) in the area of the deposits. The high resistivity zones suppress and distort coincident IP responses, calling f or high quality surveys and special care in interpreting the IP data.Electromagnetic methods are not effective in locating the deposits. This is due, in part, to masking by conductive cover. The Jojay Lake deposit has a strong magnetic response. A more indirect magnetic association is seen for the Tower Lake deposit. The Laurel Lake deposit has no magnetic signature. Magnetic data are useful in defining structure in all cases.All three deposits are outlined in the IP survey results. IP anomaly amplitudes from the pole-dipole array are from two times (Tower and Laurel Lak e) to six times (Jojay Lake) background values. Gradient array IP anomalies are of less amplitude. The spectral time constant is short for the Tower and Laurel Lak e deposits and long for the Jojay deposit. This implies that the metallic sulphides in the Jojay deposit are more interconnected than those of the other two deposits. INTRODUCTIONInduced polarization / resistivity surveys are commonly used in gold exploration program s in the Canadian shield because the IP method is effective in detecting disseminated metallic sulphides which are often found associated with gold. Other common geophysical sur vey methods such as magnetics, VLF and EM are not generally capable of direct detection of disseminated sulphides. Since the introduction of the IP method in the 1950s, it has undergone continuous improvement. The most recent improvement is the development of time domain receiver s which sample the full de cay and record it in digit al form. This results in a more complete measurement of the response which permits analysis and enhancement of data quality and the derivation of a nomaly parameters which characterize the measured decay. This extension of conventional time domain IP methods is called spectra l IP, a term first introduced by Pelton et al. working in the frequency domain Spectral IP surveys are attractive because they allow the possibility of discriminating between IP responses which have similar amplitudes but are due to dissimilar geo logic targets. The discrimination can be important in the selection of IP anomalies for follow-up.Time domain spectral IP survey results are presented over three known gold deposits in northern Saskatchewan-Tower Lake, Jojay Lake and Laurel Lake. The surveys were initiated and supported by Cameco-A Canadian Mining and Energy Corporation (formerly the Saskatchewan Mining and Development Corporation-SMDC) and were carried out by JVX Limited using the Scintrex IPR-II receiver and attendant spectral analysis software."

Jan 1, 1989

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By A. B. Barlow, D. H. Pitcher

"The Geophysics/Geochemistry Section of the Ontario Geological Survey initiated an aerial geophysical survey in the James Bay Lowlands, Cretaceous Basin area, District of Cochrane, Ontario. The survey was contracted to Scintrex Limited and was carried out in 1978. Approximately 8000 line kilometres of airborne electromagnetic and magnetic data were recorded. The Tridem airborne electromagnetic system was employed, mounted in a twin-engined PB Y Canso aircraft. This specific Tridem system uses a vertical coaxial coil configuration and measures in-phase and quadrature components of the secondary field at 500, 2000 and 8000 Hz.The primary purpose of this survey was to map subsurface conductivities and, in particular, to search for lignite deposits. Physical property measurements show that electrical methods should detect differen ces in conductivity between the moderately conducting clay-lignite horizons and the less conducting clay, soil, muskeg and gravel horizons. A preliminary Tridem test survey, as well as surface DC resistivity soundings, confirmed this approach. The interpretation of the present survey data indicates that Tridem is a suitable electrical method to aid lignite exploration in the James Bay Lowlands."

Jan 1, 1980

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By Rocky (Yaokun) Wu

Rock burst is one of the biggest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost effective yielding rock bolt. This paper introduces a new yielding rock support - Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150 ~ 250 mm of deflection at 8 ~ 10 metric tons (Mt) loads for every 16.4kJ energy input. Its performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described, the dynamic testing results are discussed; and the features and application of the bolt are presented.

Oct 1, 2010

By K. A. Hildebrant, J. R. Norgate

"Synthetic lubricants have for many years documented extended service life and provided superior performance in temperature extremes. Increasing interest in synthetics' ability to reduce energy costs has resulted in laboratory and industry application evaluations. These tests have documented savings in functions such as worm gear drives, spur gears and in compressors. Energy savings data are presented as well as payback calculations as low as thirty days.The National Research Council of Canada has estimated that the Canadian economy loses over five billion dollars per year in friction and wear. Figures quoted were for 1986 during which it was estimated that nine hundred and forty million dollars were lost in the mining industry alone"" It has been further estimated that about 115 million dollars can be immediately recovered through improved tribology practices (Table I).The purpose of this paper is to present results and savings opportunities through the use of synthetic lubricants in various but common applications. Many other areas exist with the opportunity for energy savings such as in the use of more efficient drive equipment, reduced contact seals, spray mist lubrication systems and reduced friction coatings on rotating equipment such as pump impellers"

Jan 1, 1994

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By W. H. MacLean, S. Liaghat

The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographic means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8070 carbonate, 6% chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/ybN = 1.7 to 2.8, SiO2 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y = 9, LaN/YbN= 4 to 8, SiO2 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of FeP3 (27% total iron), Si02 (14%), Cao (8%), S and K2 (+ 2%), were added, Nap was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By M. Pesowski

"Certain environmental problems can substantially alter the physical properties of the subsurface. In such cases, geophysical methods can be used to map the distribution of subsurface contamination or buried wastes prior to drilling or sampling. For example, inorganic contamination by acids, bases, salts, or metallic ions can be detected by instruments that measure ground conductivity; metallic objects such as buried drums, pipelines, etc. can be located by magnetic survey, and radioactive mine waste can be mapped by radiometric techniques. Geophysical methods can also be used to characterize site geology. If carried out prior to development, they can assist in identifying areas of high- and low permeability and sources of natural contamination. The methods can also be used to establish baseline values and to locate stable areas for development of environmentally sensitive facilities. Application of geophysical methods to environmental problems is illustrated with examples from base-metal mines, uranium operations, and potash and oil-sands operations. Particular attention is given to the problem of acid mine drainage. =IntroductionGeophysical methods have been used for many years by the mining industry in exploration and geotechnical investigations. The basic techniques for mapping variations in physical properties of the subsurface have been adapted to meet the special needs of resource exploration and development in the coal, potash , oil sands, industrial minerals, precious metals, and base-metal industries. Now the mining industry is facing another challenge: to operate the mining cycle, from discovery to closure, with minimum impact on the environment. This involves the rehabilitation of abandoned mining sites, the minimization and effective containment of pollutants at operating and developing sites, and the longterm containment and monitoring of sites after mine closures.Some of the most difficult aspects of environmental control and monitoring relate to the location of buried waste and contaminated fluids in the subsurface. As in the search for buried ore deposits or in geotechnical investigations, geophysics can be a valuable aid in subsur face environmental investigations. Investigations can be remedial , involving the location or monitoring of existing problems, or preventative, where problem areas are identified or background values are established before site development. In either case, geophysical methods should not be considered as a substitute for drilling. Geophysical interpretations in general do not provide the detail required for a complete environmental or geotechnical investigation. They are most useful as rapid reconnaissance methods for targeting subsequent drilling or for interpreting subsurface condit ions away from drill holes. Table I lists the common geophysical methods and the physical properties to which they are sensitive."

Jan 1, 1993

By Naoki Takada, Dae-Sung Cheon, Minoru Sato, Masaji Kato, Manabu Takahashi, Weiren Lin

"The permeability and specific storage of rocks and sedimentary layers deep underground are critical parameters for issues related to the buried evaluation of natural gas and oil, CO2 aquifer storage, various kind of waste storage and so on.The Shirahama sandstone of the Wakayama prefecture, Kii peninsular in central Japan, consists mainly of quartz grains with no cracks and rock fragments that are aggregations of various kind of minerals. The quartz grains have an average size of about 150 micron. The pre-existing pore sizes were distributed dominantly at approximately 1 micron, and the total porosity was about 13%.During the hydrostatic compression test, we measured permeability of Shirahama sandstone by Transient Pulse test for three mutually perpendicular directions. Permeability of Shirahama sandstone remained fairly constant while increasing the effective confining pressure. Permeability anisotropy was observed slightly in the normal and two parallel directions to the bedding planes.We used micro focus X-ray CT with high resolution of 10 micron to visualize and measure the voids space information in Shirahama sandstone. Three-dimensional data were obtained in the intact and stressed sandstone simultaneously. Pore structures and grain boundaries were clearly distinguished. Pore closure and grain movement were clearly observed with increasing confining pressure. Micro focus X-ray CT is an effective tool to visualize and measure the geometrical information in rocks.Three-dimensional medial axis (3DMA) method was introduced to quantify the flow-relevant geometric properties of the voids structure in Shirahama sandstone using µfocus X-Ray CT data. The number of connecting path between two faces, tortuosity and the shortest path distribution within an arbitrary region of Shirahama sandstone specimen were analyzed. Geometrical information on the number of connecting path shows reasonable correlation between permeability anisotropy and mutually perpendicular directions normal and parallel to bedding planes. In addition, we introduced numerical simulation of fluid flow of pressurized Shirahama sandstone by LBM, to discuss the permeability change caused by pressurization on effective confining pressure. We obtained the detailed distributions of fluid pressure and fluid velocity in relatively narrow voids space more than 10 µm. It was confirmed that pressurization effect on permeability caused by the decrease of the connecting path and the shortest path between arbitrary faces, and then caused a complex condition on fluid pressure and fluid velocity."

Jan 1, 2015

By C. Pichler, S. Luidold, C. Wagner, C. Sagadin, D. Kreuzer

Engineers and scientists have been combating the attack upon refractory materials of molten metals/matte and slags for hundreds of years. The details in many cases are still questionable or at least debatable. The corrosion is a major concern for furnace operators as refractory wear or failures inevitably results in reduced production efficiency and furnace reliability. Also the cost to industry is considerable and only a thorough understanding of all the complexities of the process will help to minimize that cost. One of the critical questions to overcome is the correct selection of refractories for the individual process steps to provide long and predictable refractory life together with high furnace availability. To understand the nature of the reactions involved in refractory corrosion, it is crucial to determine the complex thermo- chemical equilibria of the reactions occurring between the refractory materials and the process phases. A simulation model coupled with commercial software like FactSageTM is demonstrated aiming to understand the corrosion mechanisms between refractories and the molten process phases and draw implications for improving the performance of refractories and refractory lifetime. INTRODUCTION The extraction or recycling of valuable materials, e.g. metals, can be done by two main routes, pyro- and/or hydrometallurgical processing, depending on the chemical behavior of the used ore, scrap or pre-treated concentrate. Sometimes it is also necessary to use both process routes for the extraction or the recycling of valuable materials. In the case of a pyrometallurgical treatment, the usage of refractory materials is inevitable. This is mainly caused by high temperatures, prevailing during processing. The interaction between refractory material and slag, metal or matte leads to different reactions and interactions. As a main result corrosion of the furnace lining (refractory material) takes place. Hence, recurring furnace shutdowns occur for renewing the refractories. This leads to reduced production efficiency. Such refractory lifetimes are between some hours and decades, depending on the processes.

Jan 1, 2019

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By R. Prioul, J. Kear, D. Chuprakov, A. P. Bunger

"Hydraulic fracture (HF) growth through naturally fractured rocks challenges the development of accurate predictive HF models. The authors present laboratory experiments differentiating behaviours associated with orthogonal and oblique intersections between HFs and natural fractures (NFs). HFs were created in sandstone and crystalline (gabbro) rock specimens, impinging orthogonally or obliquely on an unbonded machined frictional interface. Ultrasound monitoring was used to observe the rate of propagation through the interface. A contrast was observed between direct and offset crossing for orthogonal and oblique intersection, respectively. The stresses required to promote crossing depended on the intersection angle between HFs and NFs.RÉSUMÉ La propagation des fractures hydrauliques (FH) dans les roches naturellement fracturées pose un défi pour le développement de modèles prédictifs. Nous présentons des essais en laboratoire qui différencient les comportements associés aux intersections orthogonales et obliques entre les FH et les fractures naturelles. Des FH ont été créées dans des spécimens de grès et de roches cristallines (gabbro), heurtés de manière orthogonale ou oblique sur une interface machinée, non liée, de frottement. Un suivi par ultrasons a servi à observer le taux de propagation à travers l’interface. Un contraste a été observé entre un croisement direct et un croisement indirect des intersections respectivement orthogonales et obliques. Les contraintes requises pour promouvoir le croisement variaient selon l’angle d’intersection entre les FH et les fractures naturelles."

Jan 1, 2016

By Yan Jie

A series of production technologies are described for gold recovery from complex gold concentrate blended with copper concentrate treated in the SKS smelting process comprising: 1) Feed preparation and proportionate feeding of complex gold concentrate and copper concentrate; 2) SKS smelting gold recovery operation and process control technology developed based on reaction mechanism, process simulation and slag formation optimization study; 3) a dry-process quenching arsenic collection technology developed during de-bottlenecking severe restriction of SO3 in the off-gas on As collection system by suppressing and eliminating SO3 in off-gas as a result of optimizing SKS smelting process conditions and spraying caustic soda absorbent so as to reduce off-gas dew point temperature; 4) electrorefining of impure anodes; 5) technology for recovering such precious metals as Au, Ag, Pt, Pd, etc. from high-Sb copper anode slime produced as a result of gold recovery from complex gold concentrate by using SKS smelting process. INTRODUCTION Gold concentrate resources in China are mainly found in Shandong province, Henan province and the Inner Mongolia Autonomous Region, etc. Currently, recovery of gold is based on pre-oxidation (roasting) cyanide leaching process. This process produces a large amount of cyanide-containing wastewater, cyanide leaching residue and relatively high SO2-bearing flue gas during production, which can cause increasingly more serious environmental pollution issues. Besides, this process route suffers from a relatively low precious metals recovery (70–80%) found when treating refractory gold concentrate and carbon-bearing gold concentrate. These issues have severely restricted the development of the precious metals processing industry in China.

Jan 1, 2019

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By J. Vaughn Barrie

Placer mineral deposits may exist in the nearshore and shelf regions off western Canada. These deposits could contain gold, ilmenite or zircon as well as sand and gravel aggregate. Two deposit types typical of the British Columbia offshore are: (l) modem and relict gold/titanium beach deposits; and (2) reworked relict titaniferous shelf deposits. The preservation of drowned beach heavy mineral concentrations resulted from a rapid relative sea level rise across the shallow shelves approximately 10 500 years ago, particularly off the Queen Charlotte Islands. This same transgression submerged an outwash fluvial system that had been exposed for at least 3200 years, draining areas of known gold placers.

Jan 1, 1994

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By P. Diehl, M. David

"As shortage in the supply of mineral commodities become more probable, there is an increasing need for reliable and comparable reserve/resource data. It is therefore necessary to standardize the traditional classification procedure by quantifying the three basic criteria in resource evaluation: economic feasibility, geologic assurance and recovery. For the portion of fairly well documented deposits and as far as their geologic parameters are concerned, geostatistical methods can considerably improve the quality of ore classification. In respect of economic feasibility and recovery, approved geostatistical methods can be introduced directly into the classification procedure. The concept of geologic assurance, however, requires a new interpretation in terms of geostatistical error spread. As the ""risk"" in estimating an ore parameter is also a function of the respective block size, it is reasonable to define not only upper limits for the risk intervals for each class of uncertainty, but also block dimensions which reflect the typical stage of planning associated with the different ore categories. An algorithm has been developed to block out areas inside a mine or a large panel which satisfies the constraints of an ore category in respect of the risk intervals of a parameter and in respect of their size. The method has been computerized and is demonstrated on a massive copper-nickel deposit.IntroductionFacing an uncertain future with respect to the demand and supply of mineral commodities, both governmental authorities and the mining industries show an increasing interest in a useful framework for the assessment and classification of the remaining mineral resources"". This is reflected by the recently published appraisal and classification scheme of the United Nations as well as by the new or revised classification systems of the USA; Canada or Australia. Moreover there are various classification schemes which are currently discussed in major mining companies."

Jan 1, 1982