Search Documents

By Asbjørn Solheim

The service life for aluminium reduction cells is often limited by the cathode carbon, due to preferential wear along the periphery of the cell leading to the so-called "W" wear pattern. The reason for this preferential wear is not well understood. Two mechanisms are suggested in the present paper; 1) non-stationary dissolution of aluminium carbide into a layer of sludge that periodically forms and disappears, and 2) electrochemical formation and dissolution of aluminium carbide within an aluminium carbide layer containing bath-filled pores. The latter mechanism may be related to the high local current density at the periphery of the cathode.

Jan 1, 2011

By Shuo Zhang, Wenying Liu

"In dump leaching, the efficiency of metal extraction from ores is strongly influenced by the mechanisms of fluid flow. Particle size distribution acts as a fundamental parameter in the determination of fluid flow properties in packed ore beds. In this study, we investigated the particle size distribution in dump leaching by using image analysis technique. The results showed that the particles in the dump varied from smaller than 2 cm to larger than 200 cm in diameter. P80 was calculated to be 200 cm, which was significantly higher than the historical data used by the operation. P25, P50 and P80 were found to increase non-linearly with increasing depth towards the toe of the dump, suggesting the segregation of fine and coarse particles. The image analysis results were verified by applying the rock fragmentation models. The model with the Swebrec function was found to be in better agreement with the image analysis results. Future research will investigate the effect of particle size distribution on the behaviour of fluid flow.INTRODUCTION Fluid flow plays an essential role in the extraction of valuable metals using heap/dump leaching (Amos et al., 2009). The rates of the chemical leaching reactions and microbial activities determine metal concentrations in the leachates and therefore the efficiency of the metal extraction. The reaction rates are influenced by two fundamental processes: transport phenomenon and reaction kinetics (Bouffard & Dixon, 2001). The transport phenomenon refers to the percolation of fluids through channels and pores in a packed ore bed, which carries lixiviants and reaction products to/from ore surfaces by convection and diffusion. The percolation rate of the leaching solution is determined by the hydraulic conductivity of the packed ore bed, which is a function of the permeability and the degree of saturation (Guzman et al., 2008). Permeability, an intrinsic property of a packed ore bed, is strongly influenced by the particle size distribution of the ore grains (Bouffard & Dixon, 2001). Hence, the objective of this study was to investigate the particle size distribution in dump leaching."

Jan 1, 2017

By X. Zhou

"Hydrogen induced failure and degradation in structural metals, namely hydrogen embrittlement, has been a long-standing industrial problem for more than one century and remains unsolved. Despite the proposal of numerous models, no consensus has been reached, and considerable discrepancies in experimental observations and theoretical calculations exist. One aspect that is central to the understanding of hydrogen embrittlement is the interaction between hydrogen and grain boundaries. In this study, we investigated the influence of several solute elements (i.e., Cr, Mo and Nb) on hydrogen segregation at the representative 9 grain boundary using first-principles calculations. Our results showed that the presence of Mo and Nb can reduce the tendency of hydrogen segregation at grain boundaries, while meanwhile enhance the grain boundary strength. This indicates that Mo and Nb are salutary elements that can be used to increase the material’s resistance to hydrogen embrittlement, providing new insights in designing hydrogen embrittlement resistant Ni alloys. INTRODUCTION Hydrogen embrittlement (HE), a phenomenon of hydrogen triggering premature failures in structural metals, has been a headache for industries ever since its first discovery one century ago (Johnson, 1874; Zhou, Marchand, McDowell, Zhu, & Song, 2016; Zhou, Ouyang, Curtin, & Song, 2016). It is well accepted that the segregation of hydrogen at microstructures such as grain boundaries (GBs) plays a key role in determining the occurrence and severity of HE. GBs are two-dimensional defects where significant local lattice distortion exist, which leads to large free volume and thus locations for hydrogen trapping and segregation. Numerous works have clarified GBs as the energetically preferable places for hydrogen segregation. For instance, Geng et al. demonstrated the preferential segregation of hydrogen at the S5(120) GB in several metals, and suggested a decohesion-type of HE in light of Rice-Wang thermodynamic theory (Geng, Freeman, & Olson, 2001). Birnbaum et al. illustrated that complete intergranular crack of Ni GBs can be induced by hydrogen segregation when the hydrogen concentration is sufficiently high, evidencing the significant role of hydrogen accumulation on GB weakening (Lassila & Birnbaum, 1987). Yamaguchi et al. demonstrated strong segregation hydrogen also occurs at S3 GBs in alpha-iron, showing that local hydrogen clustering (i.e., multiple hydrogen atoms, up to six, per unit cell) can be trapped at the S3 GB (Yamaguchi, Kameda, Ebihara, Itakura, & Kaburaki, 2012)."

Jan 1, 2017

By H. McIntire, R. Preston, D. Roberts

"Repeated 3D terrestrial digital photogrammetric surveys were conducted on hard rock mine pillars to characterize damage during secondary mining. Damage was quantified by measuring Depth of Failure, DOF, from spalling material and crack intensity, D21. These damage values were then correlated to visually assessed Pillar Damage Ratings and numerically estimated pillar loads. Measured damage, particularly Depth of Failure, correlated well with Pillar Damage Ratings. Numerical predicted pillar stress vs. damage exhibited the expected trend with shorter pillars being stronger. High resolution photographs and 3D models were also used to characterize damage mechanisms, which were found to be structurally constrained. INTRODUCTIONThe Doe Run companies Southeast Missouri Operations consists of six room and pillar lead mines (Brushy Creek, No. 29, Casteel, Buick, Fletcher and, Sweetwater) (The Doe Run Company, 2014). The mines are hosted in the Carbonates and Shales of the Viburnum trend with mining depths varying from 180 to 300 m. Pillars are commonly cut square with widths varying from 7 to 9 m and heights generally between 5 and 18 m, resulting in extraction ratios between 80 and 85% (Roberts et al., 1999). Figure 1 presents an idealized stratigraphic section through the Viburnum trend and Figure 2 shows a plan view of the five areas spanning the three mines included in this study."

Jan 1, 2015

By J. Sadaki, G. Dodbiba, S. Murakami, T. Fujita, S. Matsuo, H. Ono, K. Okaya

Printed circuit boards (PCBs) from discarded personal computer (PC) and household appliances were crushed by mechanical crushing or water explosion to remove mounted parts. More parts were stripped from PCB for PC composed of epoxy resin than from PCB for household appliance composed of phenol resin. In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 1073K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment. On the other hand, tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723 to 773K in air atmosphere and screening of 0.5mm. Silica was removed and 70% of tantalum grade was obtained after more than 823K heating and separation.

Jan 1, 2011

By David M. Parkes, George E. Davies

"Mathematically, the proposed formula is: ""Human Effectiveness + Technological Improvement = Success in the Nineties"". A brief review is made of geology, level of technology, management and labour situations, and range of production costs in coal producing countries. This comparison shows keen competition for Canadian coals, especially from the People's Republic of China, South Africa and Australia. Domestic competition comes from nuclear energy, hydro-electric generation, natural gas (if permitted) and eastern United States coal.The huge increase in the size and power of surface mining equipment in the last forty years led to modern large-scale open pit mining. While conventional truck and shovel operations will continue to be widely used, more continuous mining and conveying systems will be installed as pits become deeper and haul distances longer. Computer systems will become more sophisticated and their applications more widespread, leading to higher productivity and closer control of all operations and equipment performances and to partial or complete automation of certain operations.The underground revival will be driven by a new generation of mining people, cooperating to produce over 3 million t/y from 300 m longwall faces retreating over 3 km resulting in mine productivities of over 40 tonnes per man shift, as is already achieved in several mines throughout the world. Continuous operation using on-line control system will assist in consistent production with availabilities over 75%."

Jan 1, 1991

By P. R. A. Andrews

"Talc ore from Bakertalc, High water, Quebec analyzing about 60% talc, previously dry ground to about 95% minus 53 µm was beneficiated in an 11.4 kg/ h pilot-plant flotation circuit. A concentrate of 95.9% talc (necessary for paper-grade) was obtained at a recovery at 75.3% by employing 53 g/t of Dowfroth 250 collector at pH 9.2; further cleaning increased the grade to 97.2% talc at a recovery of 57.5%.Flotation of fresh ground 60% minus 44 µm ore at a feed rate of 18.6 kg/ h produced a grade of 96.4% talc with a recovery of 78.2%, using Aerofroth 70 collector a six carbon-branch chain alcohol, at pH 9.2.The similarity in the concentrate grade and recovery between pre-ground and fresh-ground ore indicated that it was not neces¬sary to grind to 95% minus 53/2m to achieve comparable selectivity. A grind of 60% minus 44 pm corresponds to 100% minus 300 µm.Flotation retention times obtained with fresh ground ore indicate 33 min. for combined rougher/scavenger, and 15 min. each for the first and second cleaners.Talc-magnesite flotation separation is explained in terms of physico-chemical forces, with reference to surface charge and adsorption mechanisms."

Jan 1, 1989

By J. Salazar

This paper presents a dynamic simulator of the semi-autogenous grinding operation deduced from first principles (non-stationary population balances) coupled to a Model-Based Real-Time Optimization (MBRTO) system to study optimizing strategies for an industrial semi-autogenous mill using genetic algorithms. For the design of the MBRTO both a validated first-principle steady-state model adapted on-line and a dynamic model were used to study the transient effect. The objective function considered is to maximize the ore throughput or the fine-product rate by changing the power-draw. For these purposes, these two performance indexes were introduced as fitness functions in the genetic algorithms. The three decision variables used were the ore feed rate, the water feed rate and the mill rotating velocity. The optimization problem was solved using a classical genetic algorithm with constant population. Constraints in the power draw and the filling level were handled by assigning a penalty function to the fitness function. Simulation results using industrial data for a large 1800 t/h copper-ore mill show the effectiveness of the system in finding the optimum controller set-points as a function of the process-operating constraints; mainly maximum ore feed rate, power draw and filling level. Starting from non- optimum conditions, the optimizer is able to improve the global performance index by 50% relative to a base case.

Jan 1, 2007

By R. L. Alexander

"Madawaska Mines Limited, incorporated in 1975 is the successor to Faraday Uranium Mines Limited. The history of the latter's mine development and corporate changes are outlined. This paper describes the geology of the Bancroft area and the rock types found in the mine, particularly the pegmatite which is the host rock for the uranium. The structure, mineralogy and distribution of the ore shoots are described with the method of grade control and mine development. The paper concludes with a summary of the production and mineral reserves.Location, Access, and PropertyMadawaska Mines Limited is located in Faraday Township, Hastings County, Ontario. The mine is in the N.T.S. quadrant 31 F/ 4, Bancroft sheet and near 46 degrees 01 minute latitude, 77 degrees 46 minutes longitude. The mine is one-half mile north of Highway 28, five miles (8 km) west of Bancroft, and is accessible by various highways from Toronto, Ottawa, Peterborough, and Belleville. (Fig. 1). A landing strip for small aircraft is located at the northwestern edge of Bancroft. Bancroft is a modern community with a population of 2,400. The company has the mineral rights to 2982 acres (1207 hectares) surrounding the mine workings and plant which are situated in the north parts of Lots 16 and 17, Concession XI, Faraday Township."

Jan 1, 1986

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By C. W. Eggert

"The idea for this talk came to me last year when I was attending the Canadian Gold Metallurgists Meeting. I talked about it to a friend of mine who is an authority on mineral dressing, particularly the theoretical end of the business. He remarked that this was an excellent technical note, why don't you write it up. This is what I have for presentation this morning. I hope in presenting this type of idea in this way it is in keeping with the tradition of the Canadian Gold Metallurgists which was to function on a not too sophisticated level and where operators could get together and trade ideas in an informal way.My basic thesis is that it should be possible to evaluate screen analyses by the application of the standard statistical probability theory. In any statistical analysis the sample is the first consideration. If we look at existing methods of size evaluation we find it is usually based on the fact that a given particle will pass one square aperature and not another. One system of standardizing how these aperatures will be set up is based on Rittenger' s work with the ratio of hole sizes proportional to the square root of 2. Keeping in mind the limitation we have accepted this as our method of 11 sizing"" in attempting to apply standard statistical methods to screen analysis."

Jan 1, 1968

By A. T. GRIFFIS, R. J. GRIFFIS

A large magnesite-talc body is locared in Delora Township, 11 km sourh-southeasr of Timmins, Onrario. The deposit occurs in part of an Archean greensrone belt dominated by volcanic and sedimenrary rocks and large bodies of ultramafic intrusions. The magnesite-talc zane is abour 1800 m long, has a maximum width of 300 m and has been drilled ro 120 m below surface. Chemical analyses of rhe main carbonate zane average 20 ro 28% soluble MgO (magnesia), 5 ro 6% rota/ iron oxide and less rhan 0.1 % CaO (lime). Mineralogically, the zane consists of approximately 54% magnesite, 28% rate, /5% quartz and 3% hematire. Perrographic srudies suggest that rhe various assemblages of magnesite, rate, quartz and serpentine were derived from a parenr serpenrinire (after dunire). An early carbonitization stage, which produced a high-magnesite, low-talc assemblage, preceded a farer decarbonitizarion stage, which formed rhe main magnesite-talc assemblage. Despite a favourably low calcium oxide content of rhe magnesite-talc rock, considerable iron in the magnesire /at rice has limited the quality of the beneficiared product: rhe besr flotation concentrate to dare yields 92 to 94% dead-burned MgO. Experimen- I L t r i i c:~:.•-4- -------- ? -_;> ,•----1---- ta/ work continues on finding a process whereby high-purity magnesia can be produced on a commercial scale.

Jan 1, 1984

By Gema Ribeiro Olivo

The hydrothermal Au-Pd deposits are hosted by the jacutinga in the Lake Superior-type iron-formation of the Itabira Group, Minas Supergroup. Jacutinga is a highly sheared, metamorphosed, hydrothermally altered iron-formation composed of hematite, magnetite, quartz, talc and phlogopite (Cauê) or muscovite (Conceição) and minor tourmaline, palladian gold, arsenopalladinite, mertierite II and palladeisite (hydrothermal) and native gold, native palladium Pd-Cu-oxides, and kaolinite (weathering products). The highest concentrations of Pd-Au occur in quartz and hematite veins parallel to the S1 foliation (Corpo Y, CorpoX, Aba Leste and Central orebodies, at Cauê and a single orebody at Conceição) or parallel to the S2 foliation (Aba Norte). The average ore grade is 30-40 g/t Au+Pd. The characteristics of the Au-Pd ore favor an epigenetic model for gold and palladium concentration in the iron-formation. During the D1 deformation and peak metamorphism, the oxiziding, acid and hot hydrothermal fluids transported Au and Pd preferentially as chloride complexes. The reaction of the fluid with the dolomitic carbonate (the probably protolith of the jacutinga) would have dissolved carbonate and K-feldspar to form muscovite or phlogopite and tourmaline, resulting in an increase in solution pH and a decrease of Cl concentration and subsequent deposition of gold and palladium minerals.

May 1, 2003

By M. Xian, M. Jahazi, Y. L. Lin

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded at different defocusing distances on two surface conditions (as-cast or machined) using a continuous wave 4 kW Nd:YAG laser system at a power of 2.5 kW and a welding speed of 6.0 m/min. Two welding modes (conduction or keyhole) have been observed. The adjustment of defocusing distance can greatly influence the establishment of conduction or keyhole modes. On the machined surface conditions conduction welding is obtained at a power density of 4.0 x 105 W/cm2. In contrast, keyhole welding is reached at a threshold irradiance of 1.5 x 106 W/cm2. Neither conduction nor stable keyhole modes have been established at a range of power density from 7.7 x 105 to 1.2 x 106 W/cm2 on the machined surface conditions. On the as-cast surface conditions keyhole is obtained at a power density as low as 4.0 x 105 W/cm2 but good surface quality is obtained at a defocusing of +2 mm. The as-cast surfaces require lower power irradiance for the formation of keyholes indicating that they have higher energy absorptivity for Nd:YAG laser beams probably due to coarse surface morphology.

Jan 1, 2004

By Joachim von Scheele

An oxyfuel-based technology - OXYFINES - has been introduced for in-plant recycling. It provides fines, dust, sludge (without any drying-step) and other by-products arising in the steel and metal producing industries to be recycled directly back into existing processes or a separate unit on-site. Results from full-scale installation (20,000 tpy) for dust treatment, full-scale and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. Processing rates at 3.5 t/h have been demonstrated. The product is agglomerates or lumpy pieces, the latter if the product has passed an all-liquid stage and thereafter been crushed. The technology does not only provide a solution to the problems connected to dust and sludge generated in metal production. It also turns these materials into a low-cost raw material useful for the production in question, thus replacing part of the raw material input in electric arc furnaces, blast furnaces, etc. Elements harmful to re-use of the processed dust or sludge, e.g., zinc and alkaline components in steel production, are removed as secondary dust, and material yield of main components for re-use is very high, about 98%. The paper reviews the concept, the results obtained and its status; its use for sludge recycling is emphasized.

Jan 1, 2004

By Jorge M. C. Soares

The CO oxidation reaction has been studied on Au/TiO2 catalysts prepared by incipient wetness (IW) and deposition-precipitation (DP) methods. Additionally the assessment of activity was also conducted on simple gold compounds (Au2O3 and Au(OH)3) and their physical mixtures with TiO2. We have found that there are three types of CO2 production from fresh catalysts, which are only dried, namely: Non-catalytic Type I (low temperature CO2 production); Non-catalytic Type II (higher temperature CO2 production) and Catalytic Type III. The DP catalysts are far more active for Type III reaction, showing activity already at room temperature, whereas the IW catalysts generally do not show steady state conversion until T>673 K. This is due to both large particle size and the presence of residual chlorine for the latter. No truly catalytic activity was found for low temperature CO oxidation on gold precursors on their own, although both Au2O3 and Au(OH)3 react well with CO even at room temperature in an irreversible manner (Type I reaction). Despite that, catalytic activity was obtained by mixing Au(OH)3 or Au2O3 with TiO2 which gives further emphasis on the importance of a good contact gold/support and the absence of chlorine.

Oct 1, 2003

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015

By S. Aram

Product Lifecycle Management (PLM) solutions have been serving as the basis for collaborative product definition, manufacturing, and service management in many industries. They capture and provide access to product and process information and preserve integrity of information throughout the lifecycle of a product. Efficient growth in the role of Building Information Modeling (BIM) can benefit vastly from unifying solutions to acquire, manage and make use of information and processes from various project and enterprise level systems, selectively adapting functionality from PLM systems. However, there are important differences between PLM?s target industries and the Architecture, Engineering, and Construction (AEC) industry characteristics that require modification and tailoring of some aspects of current PLM technology. In this study we examine the fundamental PLM functionalities that create synergy with the BIM-enabled AEC industry. We propose a conceptual model for the information flow and integration between BIM and PLM systems. Finally, we explore the differences between the AEC industry and traditional scope of service for PLM solutions.

Aug 1, 2013