Search Documents

By T. Abu Leil

A new class of ternary Mg-Sn-Ca alloys is being developed to address the dual demands of corrosion and creep resistance at service temperatures. While tin has proven to enhance the corrosion resistance, calcium is expected to significantly increase their creep resistance of binary magnesium alloys. Their effects in ternary magnesium alloys are not yet known. The series of alloys studied has Sn and Ca in the ranges 3-6% and 1¬2%, respectively. The results indicate that these alloys have two-phase structures with CaMgSn phase dispersed in a matrix that is predominantly a solid solution of magnesium. The corrosion behavior of these alloys has been investigated by means of salt spray tests and potentio-dynamic measurements. Creep behavior of these alloys was measured at a temperature of 135 C under an applied compressive stress of 85 MPa. Scanning Electron Microscopy with Energy Dispersive X-ray facility and X-ray Diffraction techniques were used to characterize the microstructures. The results indicate the prospect of designing alloys that can provide optimum combinations of corrosion and creep resistance by adjusting the relative compositions of Sn and Ca in the system.

Jan 1, 2006

By D. Nower

"The supply of copper is expected to be at a large deficit in 2012. To recover from these deficits mining companies are required to maximize production and there is no better way to accomplish this than to optimize the use of their mobile mining equipment fleets. To optimize these fleets, each equipment type has to be monitored in its own unique way. Automation would not only improve production, but also minimize the safety risks and eliminate planning errors. The automated vibration monitoring of multiple systems on the shovel can determine the machine’s condition at all times. This reduces unplanned downtime and keeps critical shovels in production. This paper will discuss the details of how shovels can be successfully monitored, continuously. INTRODUCTIONP&H Mining, part of Joy Global, is the world’s largest manufacturer of above-ground mining equipment. Its electric rope shovels, such as Figure 1, with capacities up to 115 tons (104.3 metric tons), are used for high production loading in surface mines; its draglines, such as Figure 2, have bucket capacities to 160 cubic yards (122 cubic meters). P&H also produces blasthole drills, mobile mining crushers and other essential mining equipment. Headquartered in Milwaukee, WI, the company does business on every continent, except Antarctica. ECONOMIC FACTORSDue to the global demands for metals and power, mines are required to operate at full capacity. Mine operations cannot afford any critical assets to shutdown unexpectedly; depending on the ore type and quality, downtime for a single shovel can be as much as $300,000 per hour.Electric rope shovels are one of the most critical assets in open pit mining. They are very large, complex machines with DC or AC motors, multiple reduction gearboxes (some of them complex planetary) and multiple large rolling element bearings. This complexity, combined with the tough 24/7 service, results in too much unplanned shovel downtime, which can affect the entire downstream process."

Jan 1, 2012

By K. E. Waters, N. Brodusch, R. Gauvin, A. Jordens, Teng. C., H. Demers

Rare earth elements (REEs) become increasingly significant for renewable energy devices and high-technology electronic products because of their large-scale popularity and applications. In this project, a field-emission scanning electron microscope was used to characterize the composition and distribution of REEs-bearing minerals. X-ray elemental maps were acquired with a large area x-ray detector (60 and 80 mm2 collecting area) and annular detector (60 mm2 collecting area), which allow fast x-ray acquisition at high count rate. These elemental maps were transformed into phase maps, which are used to identify the composition of the mineral phases and the REEs distribution over a large area. The phase maps are an easy way to distinguish the phases with and without REEs and compare the efficiency of different REEs extraction processes. Different methods (manual and automatic) for producing phase map were studied by comparing the distribution of REEs obtained from the same area.

Jan 1, 2015

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By M. du Plessis, G. More O’Ferrall, A. Hartzenberg

"Lonmin Platinum has experienced several cases of large-scale hangingwall instabilities during the extraction of the Upper Group 2 Chromitite Layer (UG2) at a number of the Marikana operations along the Western Limb of the Bushveld Complex. These instabilities were all attributed to the presence and interaction of prominent geological features and highlighted that assumptions made in the design of the stable pillars and stable span were potentially overly simplistic in these areas. Investigations into the various case studies over the past ten years have resulted in the identification and classification of the rock mass characteristics of the geological structures causing the instabilities.In order to get a better understanding of these instabilities, it is important to understand the structural geology in general, and the sequence of events that led to the formation of the Bushveld Complex in particular. The tectonics involved in the formation of the various layers around the economic mineralized layers has been investigated, and the influence of these tectonic events on the stability of the UG2 stopes hypothesized.Following this investigation, the behaviour of the various layers in the hangingwall of the UG2 is better understood. This paper presents a description of the ground conditions being experienced in the underground stoping environment, the possible source of the associated structures and the resultant behavioural mechanism of these structures causing the rock mass instabilities."

Jan 1, 2015

By F. A. Charalambous

Brannerite is commonly referred to as a refractory uranium mineral as it is usually highly resistant to acid leaching. There is however widely varying literature data on brannerite leaching, with some studies reporting that brannerite leaching can be achieved under relatively mild conditions. The differences observed for brannerite leaching are most likely due to the high degree of variation in the composition and structure observed in natural brannerites. These aspects of brannerite chemistry however are not very well understood due to a lack of fundamental research. The aims of this study were to investigate and develop methods for synthesising brannerites of varying composition and to investigate the effects of composition on brannerite leaching in acidic conditions.

Aug 1, 2010

By Norma G. González

La littérature et notre expérience en Bolivie dans une communauté minière très divisée comme celle de Huanuni nous montrent le besoin d?envisager des négociations gagnant-gagnant entre communauté et entreprise minière, non pas comme un point de départ, mais comme un résultat à atteindre, qui nécessite la préparation de conditions préalables. Cela implique fondamentalement de mettre l?accent sur le processus qui permettrait par la suite aux parties de mieux traiter les questions de contenu. Suivant cette hypothèse générale, l?initiative conjointe entre le Ministère des ressources naturelles du Québec et le CECI ?Développement des mécanismes de négociation entre communauté et entreprise minière? peut dégager, après un an et demi d?expérience pilote dans le site minier de Huanuni, département d?Oruro, Bolivie, les leçons préliminaires suivantes. Ce processus requiert: ??Agir, en tant qu?organisme consultant tierce partie, selon des principes et une méthodologie qui relèvent de la Communication publique et de la Médiation ; ??Comprendre et agir à partir de la ?réalité sociale? des parties en présence: l?entreprise minière, l?État et les différents groupes de la communauté; ??Intervenir sur les ?réalités sociales? des parties, par des actions d?éducation et de diffusion dans le but de préparer les personnes, les institutions et les organisations de la société civile, à des changements durables du modèle de communications existante; Approfondir la compréhension de la ?réalité sociale? du conflit (la culture du conflit, les méthodes populaires de résolution des problèmes et de gestion des conflits) afin d?offrire aux bénéficiaires les technologies appropriées pour la transformation de cette culture de confrontation violente en gestion constructive des conflits. Par ricochet, nous espérons ainsi faciliter l?attraction des investissements dans le secteur minier.

May 1, 2001

By L. Mercier, R. Narendrula, F. Desmarais, L. Amaratunga, A. Aledresse

Thiosulfate is recognized as a promising alternative lixiviant to cyanide for the extraction of gold from ore bodies. Gold thiosulfate ([Au(S2O3)2]2), however, is not well-adsorbed by activated charcoal, making industrial scale use of thiosulfate for gold leaching impractical at present. Because of their high specific surface areas (500-1000 m2g-1) and uniform open-framework nanoporosity (pore channel diameters in the range 3-10 nm), functionalized mesoporous silicas are widely recognized as highly effective materials for the selective, rapid and high capacity uptake of mercury, gold and platinum group ions. In the present work, the efficient and rapid adsorption of gold thiosulfate by thiol-functionalized mesoporous silica (hereafter designated MP-HMS) is demonstrated, whereby the thiol groups in the materials bind with the gold complexes by ligand displacement. The adsorbed gold could be leached out using cyanide, regenerating the adsorbent for further uptake cycles. Functionalized mesoporous silica is thus a promising candidate for the preconcentration of gold from thiosulfate leachate solutions.

Jan 1, 2011

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The 'actual performance' speed-curve of aircraft plotted over a ten-year period is rising faster than the 'expectancy' speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By B. Haneman, J. A. Gorst, W. Slabbert

"The Bayer process involves the digestion of bauxite in caustic liquors at high temperature and pressure. Typically the digestion section of the plant involves the heating of liquors up to the digestion temperature followed by flashing of the digestion product to atmospheric pressure with the flashed steam used to pre-heat the incoming cold slurry. Despite the heat recovery, the digestion process is a high consumer of energy. The application of tube digestion technology in such plants has resulted in significant improvements in refinery energy efficiency with associated benefits of process simplification and refinery flow sheet capital cost reduction. This paper reviews the potential application of this technology to other metals within the non-ferrous industry.THE BAYER PROCESSA typical Bayer flow sheet is shown in Figure 1. The raw feed material bauxite (containing aluminium hydroxide as gibbsite Al(OH)3 and boehmite AlO(OH)) is digested in caustic liquors (caustic soda is the solvent) at high temperature and pressure. This process extracts the alumina and silica and any carbon present on the ore. The slurry is then flashed down to atmospheric condition allowing for heat recovery from the flashed vapour and producing slurry supersaturated in alumina.Following the digestion process the mud is removed via thickening and then pressure filtration to remove fine particulate and produce a clarified liquor with dissolved alumina in solution. The resulting pregnant liquor is then cooled allowing the alumina in solution to precipitate as aluminium trihydrate Al(OH)3. The precipitated hydrate is then filtered and washed and classified into fine and coarse fractions. The fine material is returned to the precipitation process as seed while the coarse fraction is calcined at high temperature to produce alumina. The filtrate from the filtration process (spent liquor) is then heated by the incoming pregnant liquor before being fed to an evaporation process which produced the strong caustic liquor required in the digestion process. Finally, the mud from the thickening process is washed to recover caustic and then fed to tailings ponds. The washer overflow is then mixed with the digester product to increase super-saturation."

Jan 1, 2012

By M. Holm

Coal is an important fuel for energy generation, and since there are no adequate alternatives it will also be for the next decades. The deep lying hard coal is important in particular because of its high energy content. Automation of underground mining has led to major improvements in productivity and safety. A fully mechanized longwall shearer workface has already reached a high degree of automation and provides a high productivity for example utilizing the memory cut. Current researches and developments in longwall mining are focused on extending this method by adaptive cutting drum height adjustment. The so-called horizon control is often based on memory cut methods. Horizon control in this way requires information of the environment, which can be provided by models (seam model, cut model) and coal interface detection (CID). Available CID systems only provide an optimal output under specific conditions. The authors propose the shield-data-based horizon control (SDHC) system as an alternative approach. SDHC does not require information from a CID system or an environmental model. All necessary information is provided by roof supports, shearer and process monitoring. The SDHC system was tested in simulation under different seam conditions and yielded promising results which will be presented in this paper. In cooperation with the German mining company RAG the SDHC has already reached an experimental stage. A test assembly was built up at the surface and the SDHC system was implemented on real mining equipment. To make the test scenario as realistic as possible, the SDHC system was only connected to the monitoring system, not to the simulation model. The aim of these tests was to establish the cooperation between all subsystems, find appropriate controller parameters, locate and address safety critical aspects and finally to achieve an automatic cutting drum height adjustment. An introduction of SDHC for shearer guidance is given in this paper. The experimental tests are described and the control results of the realized SDHC system on the test assembly are shown.

Aug 1, 2013

By M. Kuyumcu

After German reunification the mining industry in former East Germany was profoundly restructured. Beside privatization of profitable companies the public sector took over responsibility for the mining operations to be shut down. Therefore state-owned companies cope with technical, ecological, and social challenges. The rehabilitation and reclamation has to rededicate former mining areas to new use and provided new jobs as well. In the lignite mining districts there are around 100,000 ha of mining area, a mining caused disturbance to the groundwater balance and to the system of surface water bodies of approx. 390,000 ha. They are called the largest landscape construction site in Europe. In addition to the results and diverse experience achieved over the past 23 years, a description will follow of our new challenges and of an outlook on remaining tasks. This article will describe the financing, as well as aspects of the jobcreation policy arising from lignite industry remediation.

Aug 1, 2013

Infrared spectroscopic data collected using HyloggerTM technology is being used to assess the mineral composition of Archean iron ore bedrock and Cenozoic detrital units in Western Australia’s Pilbara region. Analysis of infrared spectra enables quantification of: (1) composite iron mineralogy, (2) composite clay mineralogy, (3) hydrous silicates and (4) carbonate mineral abundances. Stratigraphic and rock mass unit logging of core has identified several detrital and bedrock units recognisable across the Pilbara. However, due to alteration related to mineralisation, weathering and later stage precipitate overprinting, it can often be difficult to assess the detrital-bedrock boundary and the occurrences of specific geotechnical units in the detritals and bedrock, particularly when using non-core drilling techniques and traditional geochemical assays. Infrared spectroscopic data collected concurrently on core from several sites has shown distinct correlation against existing unit subdivisions and associated geochemical parameters. Where infrared spectroscopic data have also been collected on rock chips recovered from reverse circulation infill drilling, these correlations allow robust geological and geotechnical models to be developed based on the typical mineralogical-geochemical signatures. The geotechnical sub-units identified in core can be readily distinguished using the various iron and clay minerals captured by the HyloggerTM technology as opposed to total iron, potassium, and alumina captured by geochemical assays. Further, some of the minerals targeted by infrared spectroscopic analysis (eg gibbsite, white mica, vitreous goethite) and their ubiquitous presence as the products of weathering, assist in recognition of various ancient weathering surfaces and help to define the origin of the material, whether bedrock or detrital. Overall, HyLogging of core and chips allows important mineralogy focussed data to be captured at minimal additional financial outlay. Correlations against geochemical unit identifiers are robust both within deposits and between deposits. Significant improvements in the confidence of geological and geotechnical models are attained.

Jan 1, 2015

By Fidelis T. Suorineni

HydraboltTM is a Swellex-type dowel support element developed and manufactured by New Concept Mining in South Africa. Like Swellex, the HydraboltTM is a folded tube which can be inserted into a larger diameter hole without pushing. It is then activated by injection of high pressure water which inflates the folded tube to intimate contact with the walls of the borehole at a set pressure, normally 25 MPa. Unlike Swellex however, the set water pressure at the end of the inflation is maintained throughout the life of the dowel. An integral non-return valve makes this possible. The HydraboltTM is being investigated as a possible stress change measuring cell. This paper presents the results of closed form solutions, numerical modeling and laboratory test to date. Preliminary results indicate that the HydraboltTM can be used as a stress change monitoring cell in addition to its conventional role as a rock mass reinforcing element. If successful, the HydraboltTM will supplement microseismic monitoring systems in rockburst-prone ground conditions where they will give quantitative stress change data for both mine design model calibrations and means for proactive safety measures.

Oct 1, 2010

By Wilson Pascheto

One of the main outcomes of a capital project is the reliability of a new plant, system or equipment. During 20 years of experience working in various capital projects for the mining industry, the author experienced failures which have caused significant losses to Owners, in many cases amounting to millions of dollars and almost jeopardizing entire projects. Often, failures were related to faulty design, shop fabrication and/or construction. Therefore, significant opportunities exist in the Mining Industry to improve the success rate of capital projects, improve on-line time at start-up, minimize the occurrence of unplanned maintenance due to equipment failures, and all this with positive contribution to health and safety. This paper presents some examples of failures and how they could have been prevented by proper Quality Assurance methodology. It also discusses some of the main challenges in the implementation of such methodology, including awareness of the Materials discipline and availability of trained Engineers.

Jan 1, 2015

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By E. Johansson, T. Siren, K. Kemppainen

"As part of the preparations for the design of an underground repository for radioactive waste at Posiva’s Olkiluoto site on the west coast of Finland, there has been considerable site investigation work. Except the extensive surface based investigations, Posiva started in 2004 the construction of an underground characterisation facility termed the ‘ONKALO’. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. The research conducted in the ONKALO gives further information on the bedrock and groundwater conditions of the final disposal site, as well as on the impact of the construction. The ONKALO provides an excellent opportunity to investigate the rock at tunnel scale, to conduct in-situ testing in rock, to develop excavation and final disposal techniques in realistic conditions. The ONKALO has aided in collecting the data needed, supported by a Preliminary Safety Assessment, for the application of the construction license that was submitted in the end of 2012. The target is to begin disposal operations in 2022. According to current plans, the final disposal would end in 2112 and the repository would be sealed up by 2120. The testing in the ONKALO still continues several years. This paper presents the current characterisation and research activities in the ONKALO. INTRODUCTIONAfter the Finnish Government's favourable policy decision in 2001, Posiva Oy, which is an expert organisation responsible for the final disposal of spent nuclear fuel of the owners in Finland, has focused further investigations at the Olkiluoto site, western Finland (Figure 1) and has started in 2004 the construction of an underground facility termed the ‘ONKALO’. The ONKALO is not a nuclear waste repository, but more than just an underground research laboratory URL – it is an underground rock characterisation facility. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. In addition to facilitating bedrock research, the ONKALO also provides an opportunity to develop excavation techniques and final disposal techniques in realistic conditions. Later, the ONKALO facilities can be put into use when building and using the repository. The construction methods and materials have been selected in order not to jeopardise the long-term safety of the repository site. The findings of the ONKALO and other investigations will provide the knowledge needed for an application, supported by a Preliminary Safety Assessment, to construct a final repository for spent nuclear fuel at the site. Posiva has submitted an application for the construction licence for a disposal facility in the end of 2012. The target is to begin disposal operations in 2022 and the repository would be sealed up by 2120."

Jan 1, 2015

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011