Search Documents

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

By D. Bois, F. P. Hassani, M. Hossein

"A growing environmental awareness hos prompted the mineral industry to seek innovations in waste management and technology. It is estimated that over 500 million metric tonnes of solid waste each year are rejected by the Canadian mineral industry. This waste hos to be disposed of in the most environmentally and economically acceptable manner.An extensive study has been conducted to estimate the cost of implementing total tailings fill from a waste disposal point-of-view as an alternative to large-scale surface disposal of tailings. The cost of waste disposal at the surface (tailings pond), and underground (total tailings fill) for three Canadian mines which have taken part in Quebec Mine Survey conducted in 1992 are analyzed. Surface disposal is the most economical and common method of mine waste disposal in Canada. Total tailings backfill as a method of waste disposal is technically feasible but cannot be regarded as more economic than surface disposal in all . It is important to remember that while surface disposal costs are rising, due to tighter legislation and more environmental pressure on governments; the costs of preparing and placing total tailings backfill is still falling as the technology improves."

Jan 1, 1994

By S. Pinard, A. Desbiens, R. del Villar, D. Jakelski

"During the fall of 1993, a new Pill-based control strategy was installed in the B grinding circuit at the Kidd Creek Division of Falconbridge Ltd. The control strategy was first evaluated on a grinding circuit dynamic simulator (DYNAFRAG), which permitted the discrimination between more than a dozen possible control alternatives. Once the final choice was made the necessary instruments were purchased and installed. The control strategy was configured on the plant computer and is planned to be commissioned shortly.This paper summarizes the control strategy, the design procedure, the installation and the controller tuning. Some preliminary problems posed by the process prior to implementation are also presented.IntroductionIn 1990 the GRAIIM (french acronym for Research Group on Computer Applications to the Mineral Industry) of Laval University started a research project on Knowledge Based Automatic Control (KBAC). This project is sponsored by a consortium of eight mining companies under the umbrella ofMI1EC (Mining Technology Council of Canada), the Quebec Mining Association (AMQ), CANMET and the Centre de Recherches minerales (CRM). The project also benefits from important grants from the Ministere de l'Education Superieure et de la Science and the NSREC-CRD program.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged."

Jan 1, 1994

By Simon Pelletier, Jose Delgadillo, Dave Page, Pramod Kumar, Raj Rajamani, Dilek Alkac, Martin Fillion

"In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal’s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned.First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized."

Jan 1, 2012

By D. R. Murray

"A promising long-term solution to uranium tailings reclamation has been the establishment of vegetation directly on the waste material. The soil profiles of areas vegetated for 0, 3, 8 and 10years are characterized as to the extent of soil development . The characteristics are compared with the visually interpreted soil profile. Organic matter content is presently the best analytical judge of soil development. Vegetation procedures have produced a build-up of organic matter in the top 10cm of tailings where natural microbial populations flourish. The CN ratio is high and the profile depth shallow, suggesting the need for additional fertilizer applications.IntroductionThe reduction of surface erosion and improved aesthetics of uranium tailings has been accomplished by the establishment of a vegetative cover. In 1971 research concentrated on developing methods of plant establishment at minimal cost and soil amendments on uranium tailings in Elliot Lake , Ontario. One process of stabilization used on a large scale was direct seeding of grasses and legumes into the tailings which had received only limestone and fertilizer treatments. Fertilizer additions were made for varying lengths of time in subsequent years to maintain the established cover.Maintenance-free vegetation would be possible once a soil profile developed with sufficient nutrient recycle and plant regeneration capabilities(1). Tailings vegetated in 1971, 1973 and 1978 that had received either 3 or 5 years of maintenance fertilizers were examined for soil development profiles. The extent of soil development and the relative effect of time and fertilizer would provide direction on reaching the goal of a self-sustaining cover.This paper is an abridgment of Division Report MRP /MRL 81-126 of the same title(2)."

Jan 1, 1984

By P. E. Weidmark

Allard, M., Hucka, V.J., Das, B., and Borchtch-Komponietz, V.I., "Investigation of seismic vibration due to large blasts in Gaspe Copper Mines"; (in Russ); The Industry of Chemical Raw Materials; Referativnyi sbornik; 5:18-20: 1978. Askew, J., McCarthy, P.L. , and Fitzgerald, D.J ., "Backfill research for pillar extraction at ZC/NBHC"; Mining with Backfill; Proc 12th Cdn Rock Mech Symp; May 23-25, 1978; Sudbury; CIM Spec Vol 19:100-lJO; 1978. Barrett, J.R., Coulthard, M.A., and Dight, P.M., "Determination of fill stability" ; Mining with Backfill; Proc 12th Cdn Rock Symp; May 23-25, 1978; Sudbury; CIM Spec Vol 19:85-91; 1978.

Jan 1, 1979

By M. K. Aly

"ABSTRACTThis paper briefly describes the mining method proposed for the iron ore deposits in Wadi Shatti, western Libya. The iron ore produced will be used in the steel plant at Misurata on the Mediterranean coast. GeologyThe Wadi Shatti is located in the central part of western Libya. Flat iron-bearing sedimentary rocks are exposed with remarkable regularity in this valley. It occupies an area 200 km long by approximately 20 km wide trending in an eastnortheast direction between Jabal Fazzan in the north and Zel1af Sand Dunes in the south (Fig. I). Only a part of this valley has been ful1y explored by drilling on a 400- by 200-m pattern in an area of 18 km2 south of the town of Taroot. Farther to the south, no exploration by drilling can be done due to the presence of sand dunes .The iron-bearing bed is about 10to 15m thick, with a dip of 2 to 4 degrees in a southerly direction . The overburden consists mainly of clayey sandstones, 4 to 5 m thick, in the northern part, increasing to 35 m in the southern part. The iron ore bed consists of three different layers, from the floor upward: (1) Lower Reduced Ore (LRO), having a varying thickness of 1 to 7 m; (2) Magnetic Ore (MO), with a thickness varying from 4 to 12 m mainly in the central part of the area; and(3) Upper Reduced Ore (URO), with a bed thickness varying from 0 to 7 m."

Jan 1, 1980

By I Wilkomirsky, F. Parada, R. Parra, E. Balladares

"The neutral roasting of As bearing copper concentrates is confirmed well established and promising option for the treatment of this type of complex concentrate. The AS elimination by volatilization allows subsequent treatment of the calcines produced in a conventional pyrometallurgical process, by blending this product with standard concentrates.Several tests were performed using the fluidized bed pilot plant at the University of Concepción with different types of concentrates. Calcines, fines from two hot cyclones and flue dust from the ESP were collected. These materials were characterized using QEMSCAN® and the results used for the development of a mass and energy balance which took into consideration the specific chemical transformations that occurred in the reactor.A physico-chemical/kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite. The mechanism involves solid-gas reactions between chalcocite, pyrrhotite and gaseous sulfur that without the mineralogical characterization would not have been possible to propose"

Jan 1, 2014

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By Barton G. Stone

The mining and exploration industries have been using Geostatistics (Matheron, 1963) for the past forty years. It has been extensively incorporated into three dimensional block modeling software whose usage has reflected the growth in the use of personal computers since 1980. Because of the utility of geostatistical models in mining and production planning, much of the modern reserve and resource modeling is done by mining engineers, geostatisticians and geological engineers. Explorationists are initially less concerned with three dimensional models until such time as a deposit has been roughly delineated. However, the concept of regionalized variables in ore deposits deals with the effect of spatial correlations between data points in a three dimensional sample space and should be useful for optimizing the spacing of drill holes to allow maximum bang-for-the-buck in drilling programs. This paper examines three common deposit types (porphyry copper, VMS and intrusive gold) to examine whether geostatistical methods have been used to minimize drilling costs because of better understanding of spatial correlations. The three model types were chosen from publicly available corporate websites of Canadian based Junior Mining Companies. They include the Wolverine polymetallic zinc deposit of Yukon Zinc in Yukon, Canada; the El Morro Deposit in Chile (30 percent ownership by New Gold Mining Company, and the Fort Knox Gold deposit in Alaska and 50 percent ownership by Nova Gold Resources). Typically, individual mining corporations post their technical reports as CNI 43-101 reports on their corporate website as indications of the favorability or progress on their more exciting properties. Data considered for this paper was not collected or generated by the author, but the information was extracted from these publicly available sites and had a variety of authorship.

Oct 1, 2009

By John O. Marsden

Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of mineral resources. The development of step change technologies that can offer >$0.15/lb total cost benefits provides a significant opportunity for producers to achieve competitive advantage, but it has been argued that rapid dissemination of technology makes such competitive advantage unsustainable over time. This paper presents the results of a recent study that evaluates a number of historical and emerging step change technology case studies in the copper industry and quantifies the associated cost benefits for users, the impact on the production cost curve, and the duration of such cost benefits for various categories of implementers: first mover, fast follower, conservative followers and laggards. The results provide a compelling case for major, mid-tier and emerging copper producers to invest in technology development initiatives if they wish to achieve and sustain competitive advantage over the long term. INTRODUCTION AND BACKGROUND A key issue for mining companies is how much time, effort and cost to spend on research and technology development (R&TD). The economic drivers for technology development and implementation are poorly understood in our industry and the business case is clouded by some notable and well-publicized failures (McNulty, 1998). Mining companies are in business to deliver financial returns to investors. This means delivering short term results on a quarter-by-quarter reporting basis as well as sustaining and growing the company to retain and reward a sustainable longer term investor base. The cyclical nature of the commodity metal markets makes it challenging to maintain investment in research and step change technology development: Mining companies must manage through the highs and the lows of price cycles, typically ranging from 5-15 years in length. The discounted cash flow approach to investment evaluation results in weak financial justification for R&TD expenditures. A clear and compelling rationale to support longer term investment in research and step change technology implementation is required.

Jan 1, 2019

By Yuhua Wang, Wei Sun, Dongfang Lu, Yuehua Hu, Tao Jiang

"With the continuous depletion of high-grade tungsten ores, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and use of toxic collectors.The aim of this study was to develop an environment-friendly processing flowsheet, which was used for beneficiation of low-grade tungsten ore containing 0.45% WO3 from New Brunswick in Canada, and the content of arsenic is 0.68% in this materials. The objective of beneficiation studied was to obtain a concentration containing 60% WO3 with less than 0.5% of arsenic under the condition without any flotation reagents. In this environment-friendly processing flowsheet, magnetic separation technology, classification and gravity separation technology were combined and employed. Firstly, magnetic separation was employed for the first pre-concentration process, over 95% of the feed was rejected as the final tailings, meanwhile, over 85% of arsenic minerals were removed with tailings. Secondly, gravity separation tests were employed on the classified magnetic pre-concentrate in the second pre-concentration process, a second pre-concentrate with WO3 grade of 54.32% and As grade of 5.41% was obtained. Finally, two stage magnetic cleaning were conducted on the second pre-concentrate for upgrading the second pre-concentrate, the mostly arsenic and gangues were removed from the second pre-concentrate. Finally, this novel processing achieved an effective recovery of fine wolframite from low grade tungsten ore with high arsenic. A concentrate with WO3 grade of 64.81% were obtained in new opened processing flowsheet, and As grade was less than of 0.5% in this concentrate. Furthermore, remarkable feature of this processing flowsheet is environment-friendly due to avoid using the toxic flotation reagents during the whole mineral processing.INTRODUCTIONTungsten is an essential metal and is the most widely used in industrial production such as national defense, electro-mechanical products, textile and leather sectors (Srivastava et al., 2000). Wolframite and scheelite are the main mineral sources of tungsten metal. With the continuous depletion of high-grade tungsten ores and the increasing demand for tungsten alloy, the low-grade refractory wolframite has become an important source for the tungsten industry. However, the large-scale utilization of low-grade refractory wolframite is disappointedly scarce, it is due to leanness of valuable minerals, complex mineral characterization and heavy use of toxic collectors."

Jan 1, 2016

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public's awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By F. Moraw

The use of redox fuel cells in which oxygen is replaced by other oxidants such as ferric ions can have significant advantages [1-3]. For example, the cathodic reaction rate (e.g., exchange current density) can be increased by several orders of magnitude compared to the oxygen reduction reaction, and platinum group metal (PGM) catalysts are not required. As a result of the higher aqueous solubility of the oxidant in a redox fuel cell compared to that of oxygen the rate of mass transfer (e.g., limiting current density) is greater by several orders of magnitude. The redox fuel cell can achieve high efficiencies and has other fuel cell advantages. The main issue with the redox fuel cell cathode is the regeneration of the oxidant where low conversion efficiencies are achieved even with platinum group metal (PGM) catalysts. In the work discussed here the Fe3+/Fe2+ redox fuel cell cathode is characterized over a range of electrolyte concentrations and operating conditions, and electrode materials. Cyclic voltammetry and electrochemical impedance spectroscopy are mainly used for electrochemical characterization and mechanistic determination of the cathode redox couple. Further characterization with selected compositions and materials is done in a redox fuel cell (hydrogen - Fe3+/Fe2+). The mechanism and the advantages and disadvantages of the fuel cell redox cathode are discussed with respect to other approaches and other redox couples.

Jan 1, 2005

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By P. Taskinen, A. Jokilaakso

The Flash Smelting Process for copper and nickel production has been one of the most successful new metallurgical process developments in the 20th century. The experimental data from laboratory scale investigations of studies has produced information and insight into the reaction mechanisms and kinetics of the flash reactions of copper concentrates. Advanced computer models coupling chemical reactions with a Computational Fluid Dynamics (CFD) software became possible with the development of commercial CFD software together with increased computing power. Currently, there are both experimental and CFD modelling, including also CFD–DEM coupling (Discrete Element Method), studies ongoing for investigating the kinetics of matte – slag reactions in the flash smelting furnace (FSF) settler. The ultimate goal of the modelling work is to develop a comprehensive FSF model for studying the behavior of changing raw materials, both primary and secondary, and distribution of their elements between the matte, slag, and gas phases. The use of User-Defined-Functions (UDF) is one way to digitalize metallurgical knowledge and experimental information to be used for supporting process experts and development of artificial intelligence applications in metallurgy. In this paper, a review of the development of the FSF reaction shaft modelling and experimental investigations, and the current work for the settler reactions’ experiments and modelling are presented. INTRODUCTION The Outotec Flash Smelting process (Bryk, Ryselin, Honkasalo, & Malmström 1958) has been used in the copper and nickel industry for 70 years with continuous support from experimental investigations by many research groups in academia, among others Jorgensen and Segnit (1977); Jokilaakso, Suominen, Taskinen and Lilius (1991), Chaubal and Sohn (1986), Kim and Themelis (1986), and in industry Mäkinen and Jåfs (1982); Kojo, Lahtinen and Miettinen (2009); Tuominen, Pienimäki and Fagerlund (2016). It has been developed also for pyrite and lead smelting (Asteljoki, Sulanto & Talonen, 1984). A schematic illustration of the FSF and other main parts of the process is depicted in Figure 1. Also, two and three dimensional physical water or gas models have extensively been used in product and process development (Lilja & Rajainmäki 1995). During the recent decades, computer based models have increasingly been adopted in the FSF research and development (Ahokainen & Jokilaakso, 1998); Ahokainen, Jokilaakso, Taskinen & Kytö, 2006; Hahn & Sohn, 1990; Jorgensen & Elliot, 1992; Zhou, Zhou, Chen & Mao, 2014; White, Haywood, Ranasinghe & Chen, 2015) to name a few, but also in supporting engineering and sales of the technology (Miettinen 2017). Even though the reactions of the sulfidic concentrate particles have been included in the reaction shaft modelling, the complete FSF model with both gas-solid/drop and molten slag/matte drop has so far been and still is too demanding for today’s computer hardware.

Jan 1, 2019