Search Documents

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By Shaun Booth

Automating Delay Reporting to Deliver Effective Maintenance Corporate Background: Technology Company: Matrikon Inc. Global software and service provider of Information Technology and Control Solutions that deliver Business Results. Case Study Facility: Bulga Coal Handling and Preparation Plant <CHPP> Australian site, part of Xstrata, an international Swiss natural resources group. Technology: ProcessMORe ? Missed Opportunity Reporting (Delay Reporting). Matrikon?s technology implemented at many facilities, to deliver effective maintenance Matrikon International Inc. Global software and service provider of Industrial Decision Support, maintenance and control solutions, with universal connectivity to existing systems and work processes. ? 1999 ? 100 employees ? 2003 ? 450 employees ? Our offices: 20 offices worldwide: ? Quebec, Toronto, Edmonton, Calgary, Ft.McMurray, Vancouver ? U.S. ? Australia (formerly Hunter Controls)

May 1, 2003

By Richard Phiri, Mike Milupi, Jackson Kapobe, Anton Lemmer, Charles Mazala

Sustainability of plant operations in a rapidly changing mining environment requires a well-trained workforce to ensure smooth running of operations. To ensure availability of trained labor, Mopani Copper Mines PLC set up a training facility in 2013. The school offers training in Engineering, Mining and Process. The engineering section enrolls grade 12 school leavers for artisan training. Mining section offers comprehensive safety induction program to employees and contractors to meet the Mopani zero tolerance accidents safety policy. The process training section offers advanced training programs for plant operating personnel and university graduates. The program includes needs analysis, theoretical metallurgical modules, practical plant training and e-learning modules. The school also offers assaying and sampling courses. All the above courses are extended to individuals and other mining houses outside Mopani wishing to have their personnel trained. The Mopani sustainable development academy ensures that contractors engaged on the Mopani sites are fully registered, comply with all relevant regulations and have undergone induction program before they can be allowed to work on the mine. INTRODUCTION “Sustainable operation of the mining industry requires a continuous supply of trained human resources” (Kapobe et al., 2018). The publication by the Asian Development Bank (2014) argued that there was a mismatch between the demand for high-level skills and the oversupply of low-level skills. Globally, the mining industry requires continued supply of skilled manpower for its complex operations and long term projects whose sustainability is absolutely necessary. Implementation of newer technologies in plant operations to ensure cost effective and efficient operations requires trained and skilled labor at various levels to handle ever-changing challenges. Dutz (2007:152–156) made three recommendations for Building Worker and Management Skills in India: Strengthen enterprise - based training. The government should help ensure that the benefits of in- service training are widely recognized by enterprises, while simultaneously providing strong financial incentives Improve vocational training - Vocational education and training systems have been unsuccessful in preparing graduates to meet market needs, particularly because of a lack of interaction with industry. Public and private vocational education and training providers should be strengthened to make them more responsive to industry demands. Curricula should be updated to reflect modern technologies. Strengthen business, management education, management of research and commercialization - business and management education should be strengthened through public-private partnerships. Innovative management courses should be introduced. Although these recommendations were made for India, they also apply to Zambia and other low and medium income nations.

Jan 1, 2019

By Aparup Chattopadhyay, Barun K. Gorain

"Porphyry copper deposits are the most important source of copper and also gold within the orogenic belts. These deposits are characterized by low grade copper ore (0.2% to 1% copper) and host precious metals like gold, silver and platinum. A characterization tool has been developed for complex porphyry type copper-gold deposits with an aim to quantify copper and precious metal deportment. This quantification is a challenging task due to low grades and also due to the presence of both visible and invisible precious metal content in different sulphide and non-sulphide phases. Studies were initiated on various complex ore deposits and also on samples representing various processing streams such as flotation and leach products. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metals content in various species. The relevance of this characterization to metallurgy will also be briefly discussed in this paper.INTRODUCTIONA novel characterization tool has been developed for double refractory gold ores and complex copper-gold ores using state-of-the-art technology for quantitative gold and copper deportment study. The characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulphide phases and variable proportion of visible and invisible gold in different sulphides phases (pyrite, chalcopyrite, chalcocite and bornite) and iron oxide phases (magnetite, hematite and goethite). A study was initiated on various ore deposits and also on samples representing various processing streams of pilot plant batches such as flotation concentrates and tailings. This paper attempts to discuss the deportment characterization methodology through presenting results from investigations on four samples from a flotation circuit viz, Feed, Final concentrate, Cleaner Scavenger Tail and Rougher Tail samples. These four samples represent the key streams for a typical copper-gold flotation flow sheet. The key objective of this investigation was to identify and quantify visible and invisible gold along with understanding the morphology and liberation of gold associated with various sulphides, Fe- Oxides and non-sulphide gangue species. In addition, the aim of this study was also to relate this mineralogical and gold deportment information to metallurgical performance."

Jan 1, 2013

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By L. M. Pidgeon

Introduction The production of magnesium by direct reduction of the oxide has far passed the experimental stage and was responsible for 30 per cent of the recent wartime production of 246,000 tons per annum. This paper describes the small-scale experiments which culminated in a number of the wartime plants. The paper traces the author&apos;s early experiments on various direct reduction reactions leading to his choice of the ferrosilicon reduction of dolomite and the realization that this reaction would proceed at a satisfactory rate at temperatures obtainable in metal apparatus. MgO has a standard heat of formation of 146,100 cal. and is therefore one of the most difficult oxides to reduce. However, if advantage is taken of the relative volatility of magnesium metal, thermally unfavourable reactions may be utilized. In reaction MgO + X = XO+ Mg . . . . . . . . . . . . . (1) the removal of Mg as a gas at high temperatures displaces the equilibrium to the right in the face of the unfavourable thermo-chemistry which is inevitable with any X other than calcium metal. If X is carbon, not only is the reaction highly endothermic, but CO is gaseous. A temperature of l,864°C. is required to produce a pressure of one atmosphere of Mg. Between l,900°C. and perhaps 400°C., the back reaction takes place readily and special shock cooling devices are required to recover magnesium from the gaseous mixture. This reaction does not lend itself to small-scale experiments and was not examined by the author. If, in reaction, carbon is replaced by a relatively pan-volatile metal, the oxide of which is also non-volatile and possesses a fairly high heat of formation, a reduction reaction is offered which is free from the difficulties associated with carbon. The typical case of silicon will serve as an example: 2MgO + Si = SiO2 + 2Mg (g) . . . . . . . . . . . . . . . . . . . . . . (2) At temperatures above l,000°C., a positive pressure of magnesium will exist over the system. Removal of the magnesium vapour will displace the reaction to the right in the face .of an unfavourable thermal balance. Since magnesium is the only volatile component at this temperature, it may be evolved and condensed, using attractively simple distillation technique.

Jan 1, 1946

By Gianni Bartolacci, Patrice Nadeau, Szatvanyi. Gerard, Carl Duchesne, Claude Chrétien

"Combustion is used throughout the mineral processing industry to produce steam in boilers, to dry concentrates in rotary dryers, and to apply heat treatments in pyrometallurgical furnaces. Tight combustion control is very important in latter type of furnace since the combustion conditions directly affect final ore quality. However, achieving tight combustion control is not straightforward since most of the flames encountered in industry are turbulent non-premixed flames, they are affected by several unmeasured disturbances and are often produced by burning several types of fuel simultaneously, some of them coming from other parts of the plant. A novel method is proposed in this paper to improve process and product quality control as well as to optimize the combustion conditions based on digital flame color images. Multivariate Image Analysis and Regression is to used extract the flame color characteristics from images to predict the solids discharge temperature of an industrial rotary kiln. It is shown that this method yield extremely good 10 minutes ahead forecast of the temperature and should lead to a substantial reduction in product quality variability as well as in fuel consumption.INTRODUCTIONFuel-fired furnaces are often used in the mineral processing industry for various purposes, such as for the production of steam (utility boiler), in conjunction with rotary dryers to dry mineral concentrates or in pyrometallurgical processes for induration, roasting, and so forth. These furnaces are necessary in the supply chain from the mine to the metals, but their operating costs are constantly rising due to the fluctuations in fuel prices. Moreover, these processes are now targeted by the Kyoto Protocol since they are energy intensive and they produce significant amounts of CO2 and other pollutants such CO, NOx and SO2. To achieve both a reduction in operating costs (i.e. fuel consumption) and in pollutant emissions while maintaining or improving product quality, one needs to have a very good control of the combustion process."

Jan 1, 2005

By Ronald E. Hamilton

"An attempt to review the recent literature on comminution reveals at once that the subject has many ramifications and that the applications are so diverse that there are very few general statements which can be made.It. seems reasonable to start classification on the basis of size of material as Input to the comminution process. However, we find that this can only be done in a very imprecise manner.The initial step of breaking rock from its natural state of very large pieces in geological formations into sizes suitable for processing is accomplished by blasting. This step in the process has not been ex-amined in this project except to note that great changes have been made during the last decade or so in the explosives used, and in the method of handling them. We should determine what effect changes in mining methods can have on the need for crushing.The second step in the process is usually primary crushing, performed by gyratory or jaw crushers. The largest chunk which can be fed to a jaw crusher depends on the size of the machine, and should be larger than the largest fragment produced in the miring process. It is obvious that the larger the crusher, the less care required in mining to en¬sure the absence of rocks too large to be crushed. The optimum size of crusher to minimize overall cost of mining and reduction is not at all obvious, and no information on this point has come to light in this investigation.It is rather generally accepted that size reduction is most efficiently done in small stages, and that different machines have different opti¬mum size ranges of feed. For example, crushers are preferred for sizes above about 1"", rod mills for the range between 1"" and 0.1"", ball mills are preferred from 0.1""down to perhaps 10 microns, and vibratory mills, or jet mills, below 10 microns."

Jan 1, 1976

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By Toshiharu Teranishi

When we apply the Au nanoparticle superlattices to the future nanooptical and nanoelectronic devices, the control of not only the particle size but also the interparticle spacing and symmetry of superlattice are the essential problems to be overcome. First, we developed a novel synthetic procedure to precisely control the particle size of alkanethiol-protected Au nanoparticles in the range from 1.5 to 9.7 nm by the heat-treatment of the small Au nanoparticles in the solid state. Absorption and nonlinear optical properties of alkanethiol-protected Au nanoparticle superlattices were then elucidated. On the other hand, the hexagonal close-packed (hcp) 2D superlattices of small Au nanoparticles with the interparticle spacings from 1.9 to 3.6 nm were successfully prepared by using newly-synthesized ligand for single electron tunneling devices. Finally, various symmetric superlattices, such as chain (2-fold), quasi-honeycomb (3-fold), square (4-fold), etc., of Au nanoparticles could be produced by making use of interligand interactions or some templates.

Oct 1, 2003

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By John T. Whetton

"FROM 1850 when the annual production was around 50 million tons, coal output in Great Britain expanded rapidly to 225 million tons in 1900 and 287 million tons in 1913. However, during the First World War, countries which had previously bought large quantities of coal from Britain sought other sources of sup-ply or developed their own coal re-sources. Thus from the record figure of 73 million tons exported in 1913, Britain's coal exports declined until in 1938 they stood at 39 mil-lion tons. An important reason for this was the development of oil engines for marine propulsion. Today, nearly all the navies and mercantile shipping in the world have turned to oil engines. Sometime in the future, however, it is reasonable to expect nuclear power to replace oil.During the Second World War, coal output in Great Britain and manpower at the mines were reduced considerably and in 1.945, 175 mil-lion tons were produced by 709,000 miners. Exports were meagre, only 8.""7 million tons went to foreign consumption. During the severe winter of 1947, inland demand for coal exceeded production and exports were prohibited. Even importation of coal was required to meet inland demand. These were years when the coal industry of Great Britain made immense efforts to secure maximum output irrespective of economy. The energy needs of Great Britain appeared insatiable; but had it been possible to export, the nationalised mining industry could have made huge profits as there was a world shortage of coal. However, home needs were considered to be the priority and many overseas markets were lost. Other producers moved in and secured long-term contracts. Not only was the British export market lost, but also the nationalised industry had to sell the imported coal at the same prices as home-produced coal and suffered losses up to of:3 per ton. Bence, at a time when the National Coal Board might have ac-cumulated a reserve fund to cope with less prosperons times, it was having to spend large sums of money securing sufficient coal for inland consumption. This was a time when intensive efforts in the mining industry, comparable with those of many industries and establishments inclusive of the armed services during the war, would have produced a greater amount of coal and have been of immense value to the country as a whole."

Jan 1, 1960

By R. A. Leveille, M. D. Doggett

"Economic returns for the copper industry have been assessed by building cash flow models for each of the 100 new mines brought into production over the past 20 years. Ninety-one of the 100 new mines returned the assumed 8% cost of capital and generated a positive net present value (NPV) at the development decision point. Economic criteria for individual mines are highly variable with NPV ranging from -$111 million (-$111M) to +$3850M (all money values are presented in United States dollars) and internal rate of return (IRR) ranging from -8% to +95%. The copper industry collectively would generate approximately $39 billion dollars in NPV through the development of the 100 new mines.The returns to exploration ($174M per deposit) were measured by deducting the cost of exploration per deposit ($221M) from the returns to development per deposit ($395M). Overall, the copper business has provided positive returns to exploration. However, the variability in returns across deposits means that only 41 of the 100 new mines can carry the average cost of exploration. The long lead times and high costs associated with exploration result in only those deposits with large amounts of contained copper being able to cover the average finding cost of the industry.The returns to development and exploration are shown to be highly sensitive to the cost of capital and metal price assumptions. With respect to deposit type, porphyry deposits are both larger (NPV) and exhibit lower profitability (IRR) than the nonporphyry deposits. On a geographic basis, returns to development and exploration are higher in Chile than elsewhere, reflecting the larger average deposit size and lower average exploration cost per deposit."

Jan 1, 2009

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By Paul H. Atkinson

"Sampling in the mineral processing industry has always been a subject which has received considerable discussion. There have been many volumes written on theory, techniques and practical application of sampling. However, until recently, the companies were not completely aware of the potential savings available with properly designed sampling systems both to assist in pieces: control and final product values.Definition In our discussion today, we will define sampling as the operation of removing a part, convenient in quantity for analysis, from a whole, which is of much greater hulk, and removing it in such a way that the proportion and distribution of the quality to be tested, i.e. size of particle, moisture content, specific gravity content, mineral and chemical composition, are the same in both the sample and the whole.Application It has been well established that undetected errors can result in large economic losses, thus most firms depend upon some type of sampling and sample analysis as a control in their continuous processing of materials. Despite the large investment in facilities and personnel the ""analysis"" of a sample can be no more accurate or reliable than the sample on which it is being based. The importance of sampling is recognized by a great many but it is appreciated by only a few, largely because it is sometimes one of the items which is taken for granted."

Jan 1, 1976