Search Documents

By J. P. Burland

The paper describes a number of recent case histories in the United Kingdom where field instrumentation and measurements have played a major role in the design and construction of excavations, piles and foundations. It is shown that the design and construction procedures for deep excavations in London Clay are based almost entirely on the results of field measurements. Examples are given of successful application of such measurements. The present understanding of the behaviour of bored piles in stiff clays and their design is based on a number of instrumented pile loading tests. The results of these tests have led to a radically new concept of pile design in which the piles operate at their full shaft capacity under working loads thereby resulting in considerable savings in design and construction. Some examples of the successful application of this concept are given. Finally it is shown that the present knowledge of the stiffness properties of chalk is based entirely on field observations. An example is given of how direct field measurements were used to solve a foundation problem at the base of a coffer-dam in chalk.

Jan 1, 2010

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By Greg Canivan, Bernie Hertlein, Les Chernauskas, Joram Amir, Garland Likins, E. Anna Sellountou, Tim Kovacs, Peter Kandaris

Nondestructive testing of drilled shaft foundations via Crosshole Sonic Logging (CSL) is often performed as part of the quality assurance process to assess the soundness of concrete. The intent of CSL testing is to identify irregularities such as soil intrusion, necking, soft bottom, segregation, voids and other defects that could result in poor structural performance of the foundation. Over time, CSL rating criteria based on first arrival time and relative energy have incorrectly evolved to often be the sole means of determining the acceptability of a shaft. Some of these criteria have found their way into regulatory agency specifications, with acceptance values often differing from agency to agency.The purpose of this document is to review the state of the practice (including experience gained over the past 20 years), propose improved CSL rating criteria and make recommendations for additional assessment, as well as educate the industry on the proper interpretation of CSL test. CSL test results alone should not be the sole means of rejecting or accepting a shaft. A task force of industry exerts was formed to review the existing CSL rating criteria and propose improvements where appropriate. The recommendations presented herein are the consensus of the task force, which believes that they should be incorporated into future criteria, codes and specifications. This paper was produced as a joint effort between the Codes and Standards Committee, the Drilled Shafts Committee and Testing and Evaluation Committee. A task force was authorized under Testing and Evaluation Committee. The task force contributed their expertise in web-based discussions often every two weeks over a period of three years. Interested participants were invited to participate at any time. The document had two rounds of broad industry review, two rounds of DFI Technical Advisory Committee reviews, and a Public Comments process. All comments were considered in producing the final document.

Jan 1, 2019

By David Peterson, Terry Tucker, Rafael Serrano

"The Alameda Corridor-East (ACE) Construction Authority awarded a $172.6 million contract to Walsh Construction Company (Walsh) for the construction of a 2.2 mi (3.5 km) long grade separation including a 1.4 mi (2.3 km) long trench that will allow Union Pacific Railroad (UPRR) and Amtrak passenger trains to operate below ground through the city of San Gabriel, Calif. The project is necessary as the ACE trade corridor accommodates approximately 60% of the shipping containers that move from San Pedro Bay, the busiest port facility in the western hemisphere, to the rest of the country via an extensive rail network. Rail traffic is expected to increase by as much as 160% by 2020, and the resultant delays to vehicular traffic is projected to increase by an estimated 300%. The San Gabriel Trench Project is designed to mitigate the effects of this increased train and vehicle traffic throughout the San Gabriel Valley. Malcolm Drilling Company (Malcolm) was selected by Walsh to perform the specialty foundation and ground improvement work for the San Gabriel Trench.This project is part of ACE’s program to create 22 grade separations and safety improvements at 39 grade crossings throughout the San Gabriel Valley. In addition to safety improvements that will eliminate crossing collisions and delays to emergency responders, the project will reduce vehicle congestion and emissions from passenger cars and trucks having to wait for passing trains, and the project will also reduce locomotive horn and crossing bell noise to local residents.Construction of this portion of the project began in late 2012, and it is scheduled to be completed by the end of 2017, having created approximately 9,000 jobs during this period. The project is being funded from Proposition 1B transportation bonds approved by California in 2006, the Metropolitan Transportation Authority (MTA) Measure “R,” and other local and federal funds. The overall project cost is estimated to be $313 million."

Jan 1, 2017

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By Y. Z. Wang

Zhengzhou Yellow River Highway Bridge, which is under construction, has a total length of 5550 meters with bored cast-in-place concrete piles as the foundations of its piers which have a diameter of 2.20 m with a length of approximately 65 m. This paper attempts, through the introduction of the said bridge's footing pile design and construction, mainly to give an account of the following points: 1) experiment and research on deep friction pile with a large diameter, 2) calculation of vertical carrying capacity of the pile with a large diameter, 3) analy­sis of horizontal forces the footing-piles of the column-shaped piers, 4) application of normal and reverse-circulation rotary drilling technologies to the construction of bored cast-in-place concrete piles with a large diameter and 5) applying super-sonic impulse on destruction detective device to examine the quality of the pile concrete.

Jan 1, 2010

It is my great pleasure as mayor of the city of Amsterdam to welcome you today to Amsterdam, and to the 10th International Conference on Piling and Deep Foundations. The history of Amsterdam has been connected intimately with your professions of geo-engineering and geotechnology, since its very first days. It is good to be aware that you are part of a very old tradition. The knowledge that we need today to build and renew the city has been gathered over a century long process so that we fortunately can stand on the shoulders of the giants before us. During the centuries people living in this part of the Netherlands have always struggled against the water. The same waters that brought the opportunity for a seafaring country to discover the world and to build an empire in the 17th century were a threat to the low lying Netherlands.

Jan 1, 2006

By B. De Paoli

At Pietrafitta, between Assisi and Perugia, ENEL (Italian National Electricity Authority) has for some time been managing a power-station operated with lignite, mined from an open mine on the way to exhaustion. A new plant is under construction which is located in the mine that was filled with tailings, mainly clays, sandy silts, lignite and ashes produced by the power-station. The soil profile is shown in Fig. 1: the thickness of the made ground is around 27 m. The foundation of the new power-station is on 320 t piles, 1.20 m diameter, embedded in the cohesive base formation at a depth of 57.5 m. 2,350 piles will be constructed for a total length of 125 km. It is therefore one of the largest pile sites at present in operation in Italy. [ ]

Jan 1, 1994

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By Rodrigue Karam

An assessment of the geotechnical conditions at the Manhattan Cruise Terminals (Piers 88, 90, 92 & 94) was conducted after excessive settlement and structural distress was reported at Pier 92. The piers are located on the Hudson River along the west side of Manhattan, New York. The following paper focuses on the investigation and analysis performed on Pier 88 located at the western terminus of 48th Street. The pier is supported by approximately 2,500 timber piles bearing on soft organic silts and clays. The first portion of the analysis consisted of an offshore field investigation and laboratory testing to classify the subsurface soils within the project area and estimate the geotechnical capacities of the timber piles. Additionally, a settlement analysis including consolidation and negative skin friction analyses was performed to evaluate existing settlement levels. Axial and lateral analyses were performed to develop the soil springs (p-y, t-z, and q-z curves) necessary for the structural analysis.

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By Pierre Gouvin, Michael Oakland

"This paper covers the rapid response methods used to monitor the emergency response to damage to an historic structure. An architectural gem, the latest incarnation of the old south Church was completed in 1875, utilizing local conglomerate (pudding stone), combined with brownstone and other materials to make an incredible showcase for priceless stained glass and other details epitomizing the height of the American Industrial Revolution. As part of required American with Disabilities retrofits to the adjacent Metropolitan Boston Transit Authority Station (MBTA), a support of excavation system was implemented with tradition sheet piles. During excavation (SOE) it was determined that Jet Grouting would need to supplement the sheeting to close openings in the SOE. During Jet Grouting, the eastern side of the structure was bisected, and lifted over 2 inches up and to the south. The movement occurred rapidly, within minutes, and subsided when Jet grouting was discontinued. The paper will describe the nature of the immediate response to get a real time monitoring program established, and the follow on monitoring program that ensued to provide the needed information to the stakeholders about this critical structure to evaluate stability, safety and to develop a long term remediation plan. The real time systems and instruments used consisted of Automated Motorized Total Stations (AMTS) and Automated Crackmeters. The Paper will describe the techniques used to control construction in safe manner.INTRODUCTIONThe Old South Church of Boston was constructed in 1875 and is one of the best examples of High Victorian Gothic Architecture in the Northeast. (Fig. 1) shows the newly constructed Old South in 1882. The Roxbury Conglomerate used to construct the church combined with large stained glass window by Clayton and Bell of London provides its unique appearance. Like most of the structures constructed in Boston’s Back Bay at that time, the church is founded on timber piles which penetrate the fill and organic soils to bear in the upper Boston Blue Clay. The churches interior includes high vaulted plaster ceilings and a 1920’s E. M. Skinner organ with exposed pipes as long as 32 ft. in length. The Church was added to the list of National Historic Landmarks in 1970 and is a featured Boston attraction."

Jan 1, 2017

By Tomohiro Yamasaki

"At the pre-construction foundations of the controlled waste disposal site built at the Port of Kinuura, the clayey soil account for the most, and with lesser amounts of sand compaction piles and sand mat. The cement deep mixing method (CDM) was used to improve ground impermeability and to reinforce the foundations on the seawall. Laboratory mixing and testing was performed to determine the appropriate quantities of cement additive for clayey soil, SCP sand, and sand mat. The test results indicated that maintaining the design strength of qu = 1,550 kN/m2 would require C = 100 kg/m3 of cement additive for all three soil types (clayey soil, SCP sand, sand mat). The permeability performance needed to improve ground impermeability assumes a permeability coefficient of K = 1.0×10-6cm/s. And the clayey soil satisfied the performance requirements at C = 100 kg/m3. However, to improve grand impermeability of the SCP sand and sand mat required more than 5% of particles having diameters of less than 75 µm. Thus, in the latter two cases, the required cement adding quantity was C = 250 kg/m3. The test specimens at one to two weeks after the created with a permeability coefficient of K = 10-6cm/s became permeability coefficient of K = 10-7cm/s six week later due to the effects of cement solidification. So the permeability coefficient declined about one order. The permeability coefficient three months later tends to decline continued with a somewhat lower.INTRODUCTIONBetween 2008 and 2011, the Aichi Seaside Environment Center constructed the Kinuura No. 3 offshore controlled waste final disposal site at Taketoyo in Aichi prefecture. (see Figure 1). The disposal site offers a landfill capacity of 5.21 million m3 and measures 472,000 m2 in area, of which some 344,000 m2 is a managed controlled sector enclosed within an impermeable seawall."

Jan 1, 2015

By Clinton O. Rex, Adam S. Hurley, W. Morgan NeSmith

"Hartsfield-Jackson Atlanta International Airport underwent a $1.2 billion dollar expansion project centered on the construction of the new Maynard H. Jackson International Terminal. Passenger access between the new International Terminal and the domestic airport facilities is primarily via underground Automated People Mover (APM) trains. Prior to this expansion, the APM tunnel terminated beneath Concourse E, which previously served all international flights. The new International Terminal is located approximately ½-mile from the previous terminus of the APM tunnel.A paper describing the general approach to excavation support for construction of the entire APM tunnel extension from under Concourse E to the new International Terminal was published by two of the authors (Hurley and NeSmith, 2014). One of the features of note of the approach involved the intersection of the proposed new alignment of the APM tunnel extension under Concourse E with the old terminus. Specifically, the new tunnel extension conflicted with the location of the existing Auger Pressure Grouted (APG) piles supporting four columns in Concourse E. This paper presents design and installation details of the micropile underpinning approach used to support the existing columns to allow for the proposed excavation including the cutting and removal of the existing APG piles, while allowing Concourse E to remain in service during construction.PROJECT DETAILSGeneralThe construction of the APM extension required an excavation support system for a 450-ft long, 55-ft deep excavation across Taxiway Dixie and a 900-ft long, 30-ft deep excavation beneath the basement of existing Concourse E. The excavation under Concourse E required both excavation support and support of the existing columns over the proposed excavation zone. A general overview of the work area is shown on Figure 1."

Jan 1, 2017

By Babak Mamaqani

The Regional Connector Transit Corridor (RCC) is the Los Angeles Metro area's ambitious light rail project, running under the city's main thoroughfares, Flower and 2nd streets. When com- pleted, it will alleviate traffic and parking congestion downtown, while connecting thousands of residents living in the bedroom communities of Inland Empire and Long Beach to their jobs there. The rail line of 1.9 mi (3 km), which involves a $1.756 billion (€1.545 billion) budget to construct the under- ground rail line, including three new stations. They are the Grand Av Arts/Bunker Hill station at 2nd and Hope streets, Historic Broadway Station at 2nd Street and Broadway, and Little Tokyo/Arts District Station at 1st Street and Central Avenue, which will offer riders their first "one seat/one fare" ride option from Azuza to Long Beach. Regional Connector Constructors JV is led by Skanska USA Civil West California District Inc. (Skanska), in partnership with Traylor Bros., Inc. (Traylor), to deliver RCC to the Los Angeles County Metropolitan Trans- portation Authority (Metro). PB&A was the structural engineer of record (SEOR) responsible to design the shoring systems for the Grand Av Arts/Bunker Hill Station at 2nd and Hope streets, and Historic Broadway Station at 2nd Street and Broadway. The temporary shoring design for Historic Broadway Station is the focus of this article, and why the project received special recognition as a runner up for DFI's 2021 Outstanding Project Award. Two main challenges are discussed in particular: design of the shoring system considering all construction stages, and design of an underpinning system where the Los Angeles Times Building (Times Building) protruded into the station footprint.

Apr 1, 2022

By Andy Boeckmann

In early 2021, DFI formed a Foundation Reuse Task Force due to concurrent and coincidental discussions of this topic during meetings of the Subsurface Char- acterization for Deep Foundations and Testing and Evaluation committees. Interested members from both commit- tees, as well as of the Sustainability Com- mittee, joined forces to form the task force. The task force mission is to promote foundation reuse by leveraging experi- ence among DFI members and collabo- rating across pertinent committees. General goals of the task force are to identify, assess and reduce risks associated with reuse; to educate owners and decision-makers about reuse; and to improve the investigation, design, construction and testing practices associated with reuse. One of the first orders of business for the task force was to organize a roundtable discussion of foundation reuse for DFI's 46th Annual Conference on Deep Foundations in Las Vegas. Last fall's discussion was framed as a continuation of the successful "Horses for Courses" session of SuperPile '21, which also focused on foundation reuse. However, whereas the SuperPile session focused on technical content, the annual conference panel on October 13, 2021, was envisioned as a less technical conversation that emphasized audience participation while addressing approaches to decisions about foundation reuse issues. The roundtable consisted of five panelists: • • • Bryan Hartnagel, Ph.D., state bridge engineer, Missouri DOT (MODOT) Tom Bradley, project director, Stanhope, London Hilary Shields, senior geotechnical engineer, Arup, London Jim Mackey, vice president/chief marketing officer, McGee Group, London Susan White, attorney, Benesch, Cleveland The roundtable was moderated by Andy Boeckmann, Ph.D., P.E., a senior engineer who works in Dan Brown and Associates' Missouri and Illinois offices, and is an article co-author.

Feb 1, 2022

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By Ryan Sullivan, Lisa Smiley, Jewels Stover

The Westerly Storage Tunnel (WST) Project is part of Project Clean lake, the North East Ohio Regional Sewer Dist years. When completed in 2020, WST will be nearly 2 miles of 25-ft diameter tunnel 200-250 ft below ground. The storage tunnel will manage higher flow volumes, keeping stormwater out of the combined sewer system reducing overflow occurrences. Three deep shafts provide access to the tunnel at the tunnel boring machine (TBM) launch and retrieval sites, as well as a vent shaft. Support of excavation for the access shafts was constructed utilizing unreinforced concrete diaphragm walls. This innovative, value-engineered alternate design significantly reduced risks associated with conventional secant piles combined with a rib and liner plate system. Implementation of the diaphragm wall technology resulted in a water tight, continuous shaft keyed into rock. This case study examines the design, methodology, and installation challenges unique to each shaft, as well as the benefits of the final product to the overall project.

By Kaustuv Bhattacharya, Manish Kumar, Nirbhay Singh, Prodyot Kr. Ray, Praveen Soin

This paper highlights salient features of an excavation 38 m (Length) by 10 m (Width) by 24 m (Depth) carried out in Central Kolkata. Secant pile wall (SPW) formed using a combination of alternating 1200 mm & 800 mm diameter piles was used. Six layers of struts and waler beams, including bottom slab were utilized as lateral restraints to piles. The geotechnical profile for excavation zone was predominantly silty sand to sandy silt. The profile is characteristic of river channel deposit usually encountered in Kolkata. Temporary stage analysis (including seepage analysis) and design were carried out in FEM softwares. Design checks for clay bursting, piping, bottom heave, etc. were also carried out. Extensive instrumentation and monitoring were carried out during the excavation period to check parameters such as ground movement, pile movement, piezometric heads, etc. as per review levels. During excavation, ground improvement using Tube-a-manchette grouting technique was also required to be carried out as per field observations. The paper discusses some of the major challenges faced as well as measures taken to counter them, during deep excavation carried out in silty soils in a very congested Urban setting in the heart of a Megacity.

Sep 1, 2022