Search Documents

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crushed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summaries of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling at the same group of quarries. OBJECT Or STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

In 2006, a total of 4,573 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 30.7% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,042; 44.7%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=368; 8.0%), followed by Texas (n=342; 7.5%).

Jan 1, 2008

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By Steven K. Ruggieri

This report describes the use of the sprayfan auxiliary ventilation system for methane and dust control on continuous miner sections to potential users. The sprayfan auxiliary ventilation system is a modified water spray system which directs intake air to and across the front of a continuous miner to prevent build up of methane gas and dust concentrations. This user's manual contains practical information concerning sprayfan: a. Description and capabilities b. Design c. Installation d. Operation e. Maintenance. Underground tests, independent laboratory tests, tests by MSHA, and independent installations by coal producers have confirmed the performance of the sprayfan system. There are currently 150 sprayfan systems in operation in underground coal mines.

Jan 1, 1981

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By Thomas Varley

"The literature on flotation of oxidized ores except for patents (especially for reagents) is very sparse. The Bureau of Mines in 1936, published a circular on the subject, by Ralston and Allen. The treatment of oxides by flotation was then in its infancy, but several of the most important mining companies in the Western United States and Mexico are now operating flotation plants for treating oxidized ores. The purpose of this present circular is to review the progress made and bring the subject up to date. One of the writers of the 1916 report (Mr. Allen) has been associated with some of the most important mining companies who have put into practical operation the process of flotation of oxidized ores; among these companies are the Shhttuck Arizona Copper Co., Bisbee, Arizona (now the Shattuck Denn Co.) and the San Francisco Mines of Mexico, Ltd., San Francisco Del Oro, Chihuahua, Mexico. His experience and other sources of information have been freely drawn on in pre-paring this paper. Mr. Ralston, assistant chief metallurgist of the Bureau of Mines, contributed many valuable suggestions and criticisms.Sulphidizing Reagents for Oxidize Ores.The various reagents and methods that might possibly be used for sulphidizing were summarized by Ralston and Allen as follows:""Sulphidizing (1) by the use of hydrogen sulphide on either the dry or the wet crushed ore, (2) by the use of solutions of the various sulphides and sulpho-compounds of sodium, (3) by the use of solutions of the various sulphides and sulpho-compounds of calcium, (4) by the use of sulphur vapor, (5) by the use of a sulphureted oil, (6) with colloidal sulphur."

Jun 1, 1927

By Thomas P. Mucho, Thomas M. Barczak, Dennis R. Dolinar

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial-and-error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground reaction behavior based on support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health's (NIOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate application of alternative roof support systems or to design in-mine trials so that a fair and equitable comparison of different support systems can be made. A case study of the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to the conventional wood and concrete cribbing historically used at this particular mine.

Jan 10, 2000

By Piyush K. Dutta

This report describes the design, development, manufacture and incorporation of noise control features on a jumbo drill and the results of successful tests of this drill in surface and underground mines. The noise-reducing features developed under this program are applicable to future designs of jumbo mounted drills that can be cost effectively manufactured and have the potential to reduce noise levels at the operator's position from 115-120 dBA to 95 dBA or less without a reduction of currently attainable drilling rates.

Jan 1, 1985

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By Jack W. Carlson

Considering the magnitude of today's public concern with critical mineral and fuel materials, regarding both their midterm and long term availability, the Nation is fortunate to have in place and operating the coordinated data systems of the Geological Survey and the Bureau of Mines. Under the supervision and policy direction of the Assistant Secretary--Energy and Minerals, these Department of the Interior agencies have long been responsible for important mineral activities in the Federal Government. Aside from their highly respected mineral industry publications such as the monthly Mineral Industry Surveys, annual Commodity Data Summaries and topical Professional Papers and Reports of Investigation, the Bureau of Mines and Geological Survey data bases and expertise have been readily available for use in emergency situations. Policymakers and decisionmakers in government have placed major reliance upon this ready mineral data and analytical capability in World War II, the Korean War, the recent price control era, and the Arab oil embargo.

Jan 1, 1975

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By W. W. Weller

Heat capacity measurements of anhydrous cobalt sulfate (CoSO4), copper sulfate (CuSO4), nickel sulfate (NiSO4), and zinc sulfate (ZnSO4) were conducted over the temperature range 51° to 298° K. The results were used to evaluate the following entropies at 298.15° K (cal/deg mole): CoSO4, 28.1; CuSO4, 26.8; NiSO4, 24.8; and ZnSO4, 26.4. Entropies were combined with heats of formation to give free energies of formation.

Jan 1, 1965

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981

By Thomas M. Barczak

The U.S. Bureau of Mines has been conducting research to optimize the design and utilization of mine roof support systems. An objective of these efforts is to evaluate the mechanical and structural responses of various mine roof support systems under simulated load conditions in the Bureau's mine roof simulator. Underground studies are also made to evaluate the in situ behavior of support structures. The purpose of this report is to document practical applications for longwall face and gate road supports that have resulted from these studies. This report is not intended to be an all-inclusive manual on every aspect of support utilization, but it does provide a comprehensive assessment of practical considerations relating to the mechanical and structural behavior of these support systems. Forty-six recommendations are made to provide assistance to mine operators in the testing, selection, and utilization of longwall face and gate road supports. Many of these recommendations offer innovative solutions to everyday problems faced by mining personnel in the control of ground in longwall mining.

Jan 1, 1989

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930