Search Documents

By Charles Zahn

Direct mass spectrometric determination of alcohols in the presence of hydrocarbons has not been possible because of the similarity of hydrocarbon and alcohol mass spectra. Experiments have demonstrated that by converting the alcohols to their trimethylsilyl derivatives, characteristic mass spectra are obtained free of interference from hydrocarbon ion fragmentation. Hexa- methyldisilazane is the reagent selected for the conversion, An improved method of preparing the reagent is given, Mass spectrometric determination of alcohols as trimethylsilyl ethers now is not only possible without prior separation from other materials, but the range of the room-temperature mass spectrometer is also extended to include the C10 alcohol region. Water does not interfere because it is converted to hexamethyldisiloxane, which has its own distinctive mass spectral peak, Experience indicates that other compounds such as glycols, amines, and phenols probably could also be determined by mass spectrometry of their trimethylsilyl ethers. Studies on the similar detemination of phenols in coal oils have been started, When mass spectrometry is not available, gas-liquid chromatography of alcohols before and after their conversion to the trimethylsilyl derivatives probably could be performed. The preparation and properties of the trimethylsilyl derivatives of 23 alcohols, 2 glycols, 3 amines, and 1 mercaptan are detailed. INRODUCTION During investigations by the Bureau of Mines at the Pittsburgh Coal Research Center relative to the development of Fischer-Tropsch processes, complications were encountered in the mass spectrometric analysis of alcohols in hydrocarbon oils. The fragmentation peaks of the alcohols and the hydrocarbons were so similar that an accurate analysis was not possible, Since involved separation techniques are necessary to isolate alcohols from hydro-carbons for separate determinations, efforts were turned to the search for a

Jan 1, 1962

By F. E. Cash

"Explosions in bituminous coal mines are preventable. The combination of adequate ventilation, thorough rock-dusting, and water on the cutter bars of mining machines and of empty and loaded cars will certainly reduce the hazard to a minimum, if not remove it entirely. This is the attitude taken by the Woodward Iron Co. in lessening or removing the dust and gas explosion hazard from its Dolomite and Mulga mines.This report was made possible through the willingness of Frank H. Crockard, president of the Woodward Iron Co. to make records available and to authorize their publication for the benefit of the coal-mining industry.The compilation of these data and preparation of maps was facilitated by the cooperation of M. Heard, general superintendent of coal mines, J. B. Whatley, assistant general super-intendent of coal, and R. P. Whetmore, chief mining engineer.The Dolomite and Mulga mines are about 16 miles southwest of Birmingham, Jefferson County, Ala., on a company owned and operated railroad which connects ore mines, coal mines, coke ovens, and furnaces.In the Dolomite property there is a 30°, 860-foot, double-tracked slope for hoisting, three manway and air slopes and one air shaft, all in rock.At Mulga there is a 220-foot hoisting shaft, an air shaft and two manways, and material and air slopes, all in rock to the coal bed.The coal in both mines comes from the Pratt bed, which is the next coal above the Mary Lee bed in the Warrior Basin. The coal is horizontal or slightly undulating, with thickness varying from 36 to 72 inches and averaging 50 inches.The method of mining is essentially room-and-pillar with modifications for mechanized sections. The mines produced approximately 1,100,000 tons with 2,328,309 man-hours exposure n 1929 and 900,000 tons with 1,697,436 man-hours exposure in 1930.Through the work of the safety department the entire personnel in the coal mines, as well as in other departments, makes safety an essential part of efficient operation.Both mines are gassy; Dolomite produces about 334,000 cubic feet and Mulga about 919,000 cubic feet of methane every 24 hours.The ventilation maps, two of Dolomite mines (figs. 1 and 2) and one of Mulga (fig. 3) give as much of the details of ventilation as is practicable to put on maps of such scale. As will be seen from these maps there are two main ventilating fans in Dolomite mine and two in Mulga mine and the general direction of the air travel is indicated by long arrows to fan 1 and short arrows to fan 2 in each mine. Each fan has a gas or steam auxiliary drive and each mine has a complete fan and power unit ready for operation in emergency.In Dolomite, recently taken data show that fan 1 exhausts 82,000 cubic feet of air per minute at 3.2-inch water-gage pressure, with an analyzed methane content of 0.15 per cent, and fan 2 exhausts 115,500 cubic feet of air at 3.8-inch pressure and 0.10 per cent of methane. In addition, a Capell fan at No. 2 air shaft is a standby or emergency unit.In Mulga recently taken data show that fan 1 exhausts 83,000 cubic feet of air per minute at 3.0-inch pressure and 0.18 per cent of methane, and fan 3 exhaust 119,000 cubic feet of air per minute at 5.4 inch pressure and 0.35 per cent of methane. Fan 2 at No. 2 shaft is a standby or emergency unit for the Mulga mine.The ventilation is on a split system in both mines. All part split and total returns are measured, sampled, and analyzed weekly, requiring one man two days each week. During December, 1930, 77 samples were collected and analyzed in Mulga and 78 in Dolomite. Two weekly reports covering part of December, 1930, are given here so that they can be studied to show control of ventilation in the Dolomite and Mulga mines. In the event that a split sample shows more than 0.50 per cent of methane, immediate steps are taken to lower the explosive-gas content. The reports follow:"

Mar 1, 1932

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By Alan A. Campoli

The U.S. Bureau of Mines evaluated two different conventionallongwall gate entry systems in the Southern Appalachian Basin, where mining and geologic conditions are conducive for coal pillar bumps. These gate entry systems were in a coal mine located in the Pocahontas No.3 Coalbed under approximately 2,000 ft of overburden and a massive quartzite sandstone member, and both employed a center abutment pillar flanked by yield pillars. The 8O-ft-square tailgate abutment pillars within the first study area began bumping 500 ft in advance of mining. This was accompanied by face bumps on the tailgate corner of the longwall face. The 120-by 180-ft tailgate abutment pillars within the second study area did not begin to bump until mining was approximately 100 ft past. Coalbed stress change and abutment pillar dilation data demonstrated that a 15-ft-wide perimeter of yielded coal surrounded a highly stressed core in both sizes of abutment pillars. The 62 pet more core area per foot of gate entry in the larger abutment pillars prevented excessive load transfer to the corner of the tailgate panel and eliminated the face bumps experienced with the original gate entry design.

Jan 1, 1990

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By Arno C. Fieldner

The objectives of the coal-research activities of the Bureau of Mines are very well expressed in the organic act of Congress establishing the Bureau. It reads as follows: That it shall be the province and duty of the Bureau of Mines, subject to the approval of the Secretary of the Interior, to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources, through the prevention of waste in the mining, quarrying, metallurgical and other mineral industries; to investigate explosives and peat; and on behalf of the Government to investigate the mineral fuels and unfinished mineral products belonging to, or for the use of, the United States, with a view to their more efficient mining, preparation, treatment, and use; and to disseminate information concerning these subjects in such a manner as will best carry out the purposes of this act.

Jan 1, 1946

This Bureau of Hines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By Jaan Kiusalaas

This report is a self-contained User Manual for a computer program called SPASID -- Subsidence Prediction and System Identification. The program has two primary functions: (i) Precalculation of ground movements due to underground mining operations using the influence function method; (ii) Computation of influence function and site parameters from measured displacements. SPASID is written in FORTRAN and consists of four modules: (i) Preprocessor Module that prepares and maintains surface and mine data bases; (ii) Subsidence Computation Module that predicts movements of the surface; (iii) System Identification Module which is used to calculate the optimal influence function parameters, and (iv) Postprocessor Module for generating graphic displays of subsidence data. The last module is somewhat machine dependent but has internal documentation to indicate potential changes. All of the modules may be run in either batch or interactive mode. The manual does not assume previous knowledge of the influence function method or programming competence.

Jan 1, 1983

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By Terry J. Close

From 1981-84, Bureau of Mines personnel examined and evaluated mines and prospects in the highly mineralized 62,400 acre Inyo Mountains U. S. Bureau of Land Management (BLM) Wilderness Study Area (WSA), located east of Lone Pine, CA. The 62,400 acres studied is the part of the 87,145 acre WSA designated as suitable prior to February 28, 1983. The WSA is underlain principally by quartz monzonite and quartz diorite that have intruded sedimentary and volcanic rocks. Three types of mineral deposits are present: 1) gold in fissure veins, 2) silver in fissure and replacement veins, and 3) talc in metasomatic lenses. Of the 84 nines, mills, and prospects examined, 54 are significant: 1) 5 in the intrusive rocks total about 4.4 million tons of inferred marginal gold reserves averaging 0.24 oz gold and 0.74 oz silver/ton; 2) three associated with intrusive-sedimentary rock contact zones total about 280,000 tons of inferred subeconomic silver resources averaging 7 oz silver/ton; 3) 27 gold and silver occurrences in the intrusive and sedimentary rocks total about 1.2 million tons of material in poorly defined bodies too small or low grade to be resources; 4) 15 gold and silver occurrences in the intrusive and sedimentary rocks are too poorly exposed to estimate tonnage and grade; and 5) four talc deposits along intrusive-sedimentary contact zones have inferred marginal reserves totaling about 640,000 tons. The marginal gold reserves at $450/oz might be profitably mined (reserve) at a gold price of about $600/oz and the subeconomic silver resources at a silver price in excess of about $27/oz. The marginal talc reserves might become minable at prices of about $50/ton and $80/ton for unprocessed and processed talc, respectively, after present supply sources are depleted. At most of the 54 significant mines and prospects, additional reserves or resources would likely be disclosed by trenching or drilling. Present in the WSA are 13 gold mills, numerous small pits and cuts, 270 underground workings totaling about 36,000 ft, and 80 mining benches totaling about 11,000 ft. Gold, silver, or talc were produced from most of the workings. A total of 1,561 lode and 18 placer samples were taken.

Jan 1, 1985

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980