Search Documents

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

By Norman G. Foster

The mass spectra of 14 previously unreported alkylthiophenes are pre-sented. Low ionization voltage data of selected compounds from these 14 and 23 previously reported alkylthiophenes are presented and discussed for their value in supporting fragmentation mechanisms analytical correlations. A comparison with and corroboration of earlier correlations is made. Additional correlations concerning detection of side chain branching and the detection of ethyl-alkyl and propyl-alkylthiophenes are made. A discussion of the possible fragmentation routes and mechanism of fragmentation is given. Speculative structures are inferred s out some of the ions and hence this work provides a basis for suggesting fation mechanisms for the alkylthiophenes according to modern theories ass spectrometry. Verification of these mechanisms must await the availability of isotopically labeled molecules which are labeled in specific lotions that permit the definition of the paths of frag-mentation. Some suggestions for further work to generalize on the correlations and studies made to this point are presented.

Jan 1, 1965

By Oliver C. Ralston

[The NOJ'l..metals Division deals wi tt mi:leral n t inte .ded to be used a ra\o,f materials for extraction of metals. ~ _ ereas, a. materinl containing a chromite, if used' for production of c~1r()rrti1..1r.'l ::tetE' .. l or fcrrochromiu"1, 1,oJould be a chromi te ore, if used as 8. rcfrn.cto~J or for prod .1.ction of chromium chemicals, it is a chromi te-beari [. ~?oCl... Li;{eHise, a r:1a&neti te used for production of iron is a metallifero"'..ls ~in8re..i; if used 8.S a water-filtration granule in .:l magne.tically cleaned filter bed, it 'ould be a nonmetallic in-dustrial mineral.]

Jan 1, 1940

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By A. R. T. Denues

This investigation was made under a cooperative agreement between the United States Department of the Interior, Bureau of Mines, and the Pittsburgh Testing Laboratory. Funds were supplied by the Chile Exploration Co., whose executive offices are in New York City. The support, cooperation, and services of these agencies made the work possible and are acknowledged gratefully. The writer wishes to express his particular indebtedness to the staff of the Explosives Division of the Bureau of Mines for services and assistance, particularly Dr. Wilbert J. Huff, consulting explosives chemist, J. C. Holtz, J. E. Tiffany, and A. B. Coates; to F. O. Gardner, treasurer of the Pittsburgh Testing Laboratory; to G. B. Holderer, consulting engineer in connection with liquid-oxygen explosives for the Chile Exploration Co.; to the Enos Coal Mining Co. of Oakland City, Ind., particularly to G. H. Utterback of the staff of the mine for providing facilities that made field tests possible; and to full-time assistants J. W. Rothhaar and J. G. P. Weinheimer and to W. S. Hiller, part-time assistant, who were employed under the cooperative agreement.

Jan 1, 1940

By J. Fletcher Smoak

Consumption of abrasive materials in the United States in 1981 was approximately $340 million, of which 37 % was industrial diamond (natural and synthetic), 39% manufactured abrasives, and 24% natural abrasives. Production and shipments of natural abrasives, excluding emery and industrial diamond, decreased in quantity 9% and 7%, respectively, when compared with that of 1980. Emery showed the largest change in output, decreasing 30% in quantity and 20% in value. Production of nonmetallic .manufactured abrasives material plus shipments of metallic abrasives material decreased 5% in quantity but increased 4% in value. Nonmetallic manufactured abrasives consisted of aluminum oxide (fused) and crude silicon carbide produced in the United States and Canada and accounted for 63% of the value of all manufactured abrasives. Metallic abrasives shipments included chilled and annealed iron shot and grit, steel shot and grit, plus cut wire, aluminum, and stainless steel shot and equaled 37 % of the value of all manufactured abrasives.

Jan 1, 1982

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By E. J. Matson

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. The Rush Creek lead-zinc deposit, Mono County, Calif. (fig. 1), was examined by W. T. Benson in July 1944 and again in September 1945 by D. W. Butner, engineers of the Bureau of Mines. From the results of these preliminary examinations, a core-drilling program (fig. 2) was started in August 1946 and continued until November 1946, when work was stopped on account of inclement weather. Field work was again started in May 1947 and completed in June 1947. The drilling program was laid out to develop the horizontal .and vertical extensions of showings exposed in surface pits.

Jan 1, 1949

By R. Blickensderfer

Several thin film absorber stacks with spectrally selective characteristics were developed by the Bureau of Mines. The stacks consisted of a silicon thick film or a zirconium compound thin film on a reflective thin film of silver. The zirconium absorber films, with the general formula ZrCxOyNz, were prepared by reactively sputtering zirconium or zirconium carbide in argon with small amounts of oxygen, nitrogen, or both, or by oxidizing zirconium films in air. A few similar types of films were prepared from titanium. The short-wave absorptance over the solar spectrum, a(s), and thermal emittance at 600 K, e(600 K), of the solar absorber stacks were calculated from room-temperature reflectance data. The values of a(s) ranged from 0.47 to 0.93, e(600 K) from 0.49 to 0.034, and the ratio a(s)/e(600 K) from 1.7 to 34. The specimen with the best combination of properties, a ZrNx-Ag stack, had a solar absorptance a(s) of 0.85 and a ratio, a(s)/e(600 K), of 24. The effect of film thickness and composition on spectral selectivity was determined. An emissometer for measuring normal total emittance up to 800 K and a method for determining a (s), e(T) (hemispherical), and a(s)/e(T) using simulated solar radiation are described. A calorimetric method for measuring a(s) and e(T) (hemispherical) at elevated temperature is also described. Measurements made on several specimens agreed favorably with calculated values.

Jan 1, 1976

By B. E. Davis

The Bureau of Mines conducted tests on samples of two Florida phosphate slimes t6 devise a technique to recover phosphate currently dis-carded because of its fine size. A flotation technique was devised to recover the phosphate contained in two fractions of each slime: the plus 37um fraction and the plus 20-um fraction. The technique involved conditioning the flotation feed with sodium silicate and a fatty acid-fuel oil emulsion, floating a rougher phosphate concentrate, and cleaning the concentrate in two cleaner stages with sodium silicate added to each for gangue depression. Concentrates containing 21.0 to 32.3 pct P20S were produced with recoveries of 68.1 to 84.2 pct of the P20S con-tained in the flotation feed.

Jan 1, 1987

By Raymond O. Dannenberg

The gas-combustion retort developed by the Federal Bureau of Mines at the Rifle Oil Shale Project near Rifle, Colo., is a continuous, gravity-feed retort. The heat required to convert the kerogen in the oil shale to liquid oil is generated by the combustion of product gas and carbonaceous residue remaining on the retorted shale after the kerogen has been converted to oil, gas, and residue. A study of the effects of the process variables on retort operation, product yields, and product properties is important to the successful solution of the problems encountered in the development of a satisfactory process. Statistical methods were used to design the experiments and analyze the effects of the rate of shale throughput, the composition of dilution gas, the height of the shale bed above the air entry, air-gas distributor design, shale size range, and the ratios of the flow rates of the various gas streams entering the retort to the rate of shale throughput.

Jan 1, 1960

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Monongalia County, W. Va. It is one of a Bureau of Mines series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.5 million tons of coal was produced in Monongalia County in 1957, of which more than 7 million tons was cleaned mechanically in 8 cleaning plants. On January I, 1954 the Bureau of Mines estimated that 1,576 million tons of recoverable coal remained in the county in beds 28 inches or more thick.

Jan 1, 1960

By O. C. Blade

This survey report, the first for this type of fuel, is issued to provide information on the characteristics of the burner-fuel oils now manufactured for sale. Reports of surveys of diesel fuel, conducted under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines, United States Deportment of the Interior, have been published annually since 1950.2/ This survey of burner-fuel oils is similar to the diesel-fuel surveys In pattern and has been conducted under an extension of the same agreement at the request of the Oil-Heat Institute of America and the petroleum industry. It is not intended to conflict with the diesel-fuel survey but rather to supplement it. Burner-fuel oils, also specifically referred to as heating oil, range oil, furnace oil, "Bunker C," and fuel oil, are sold in increasing volumes for use in this country and for export. Sales of all grades of fuel oil in the United States have increased from 340 million barrels in 1926Y to over a billion barrels per year. 4/ Distillate fuel oil sales, in proportion to total fuel-oil volume sold, increased from 42 percent in 1950 to 50 percent in 1954. Sales of distillate and the heavier residual oils during recent years are shown: [ ] It must be realized that the data given are not accurate indications of the use of these materials as burner fuels. Some burner fuel, used as range oil, is kerosine, which is not included above. A large volume of fuel oil--approximately 30 percent of the distillate type and some residual fuel oil--is sold as diesel fuel. Smaller

Jan 1, 1955

By D. K. Deardorff

The purpose of this work was to investigate the hafnium-carbon phase diagram. Alloys used to study this system were prepared from high-purity components by both consumable-and nonconsumable-electrode arc melting. Data for the diagram were obtained on the alloys by metallography, optical pyrometry, thermal analysis, heat treatment, and X-ray diffraction. The data indicate that a carbide compound occurs over considerable range of composition, and that one of each of the following types of reactions occurs in the hafnium-carbon system: Peritectoid, peritectic, and eutectic. The maximum melting temperature of hafnium carbide is 3,840° C at 49 to 50 atomic percent carbon, and the composition range of hafnium carbide at temperatures of 2,150° to 2,380° C is from 37.0 to 48.5 atomic percent carbon. The hafnium a-S transformation temperature is raised on alloying with carbon from 1,750° to 1,890° C, where a peritectoid reaction isotherm occurs. Alloying hafnium with carbon increases the hafnium melting temperature from 2,190° to 2,250° C, at which temperature a peritectic reaction occurs. Hafnium carbide and carbon react at 3,055° C to form a eutectic of 68.3 atomic percent carbon.

Jan 1, 1967

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By S. L. Weber, Y. H. Cheng, D. E. Banks, J. K. H. Ma

"The aggressive industrialization of America, the development of powered tools which generated massive amounts of respirable-sized dust particles, a latency period which may mask the relationship between exposure and development of disease, inadequate (or perhaps even careless) understanding of the relationship between dust exposure and disease, and respiratory protection which has later proven to be inadequate have resulted in a series of epidemics of silicosis which have caused the premature death of many workers.1-11 Emphasis on the regulatory control of dust levels in the workplace has greatly reduced the development of pneumoconiosis in the United States and in other developed as well as underdeveloped countries, yet the prevention of silicosis or coal workers' pneumoconiosis has not come close to being accomplished. Despite the public health perspective that pneumoconiosis arc totally preventable illnesses, there appears to be little evidence that this is the case.Cases of pneumoconiosis continue despite aggressive enforcement policies by regulatory agencies, attempts at dissemination of very readable materials aimed at workers and management 12.13 and respiratory dust exposure standards which are in place and appear, for the most part, protectivc.14- 16 It is more than frustrating for all parties associated with advocating workers' health to see reports of workers with aggressive silicosis. On another level, both the physician and the affected worker are helpless when a diagnosis of silicosis or coal workers' pneumoconiosis is made. Both realize that there is no proven way to affect the natural history of these progressive inflammatory and fibrotic processes. Neither is there any ""compassionate use"" therapy. What must be developed, at the very least, is a ""salvage therapy"" which has the potential to reverse, or at least dramatically lessen, the aggressive natural history of silicosis which develops over relatively short time periods. Because of the aggressive nature of silicosis (compared to coal workers' pneumoconiosis) attempting to develop a therapy for this illness should be a priority."

Nov 1, 1995

By C. W. Smith

The U.S. Bureau of Mines; Tuscaloosa Research Center, in cooperation with the U.S. Army Corps of Engineers under interagency Agreement No. 14-09-0078-1510, conducted a comprehensive sampling program of 10 upland disposal sites along the Alabama, Black Warrior, and Tombigbee River systems in Alabama. Samples from each site were characterized according to particle size, chemical analysis, mineralogical content, and potential end use. Additionally, samples were subjected to the Toxic Characteristic Leachate Procedure to determine the presence of potentially harmful heavy metals. Based on the results of these studies, each sample was determined to have properties amenable for use as aggregate in general-purpose portland cement concretes and certain asphalt concrete applications.

Jan 1, 2010

By Robert V. Spencer

"This report describes an examination and preliminary exploration of the Magnet Cove Rutile Co. property in Hot Spring County, Ark. The company in 1944 was producing titania for use in-the welding-rod and metallurgical industries but later ceased operations. The deposit appeared to contain potential reserves of rutile ore, and the Bureau of lanes in 1945 conducted an examination designed (1) to obtain samples for ore-dressing tests and (2) to gather information regarding the grade, character, and size of the deposit. This report presents the data obtained by geologic mapping, geophysical surveying, churn drilling, and core drilling. Beneficiation tests are being made at the Bureau of Mines Rolla, No. station, on the samples taken and will be discussed in a later report.The Magnet Cove operation had been called to the attention of the Bureau of Mines, and in view of the potential reserve of titanium-bearing material, it was decided to obtain samples for ore-dressing tests. Churn drilling was selected as a means of obtaining representative samples, and geologic mapping and geophysical surveying were done to throw more light on the nature of the deposit. Subsequently, a few holes were core-drilled.The property contains the NE1/4, W1/2 fractional NW1/4 and 82 acres of the N part of SE of sec. 18, and -29 acres of the SW1/4 NW1/4 sec. 17, all in T. 3 S., R. 17 W., Hot Spring County, Ark. The mine and mill are about 1 mile by graveled road northeast of U. S. Highway 270, a paved road connecting Malvern, 10 miles south and Hot Springs, 12 miles west. The area is served by two railroads, the Missouri Pacific, which passes through Malvern and Hot Springs and the Chicago, Rock Island & Pacific,,has a line connecting Malvern and Hot Springs an passes about 2 miles south of the property. A natural-gas pipe line and an electric power line reach the property."

Sep 1, 1946