Search Documents

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By William H. Lesser

A recent survey of pumping plants in the anthracite region of Pennsyl¬vania showed that more than 90 percent of the pumps in use are the horizontal centrifugal types (1).2/ This report on the design and operation of centrifugal pumps should be helpful to engineers of the region who must select pumps that are best suited to particular pumping conditions in anthracite mines. Before a centrifugal mine pumping plant is designed, the special features of the pumps that may be used should be considered, especially when low repair costs and continuous operation during flood periods are prerequisites, and when acid mine water is to be pumped. Two important advantages of a centrifugal pump are that the flow is continuous and that it can be throttled without developing excessive pressure or overloading its driving unit.

Jan 1, 1950

By Curtis D. Edgerton

The Pittsburgh Mine Map Repository of the Bureau of Mines serves as a basic reference file for the archival preservation of mine map data of mines east of the Mississippi River. About 22,000 of an estimated 500,000 available mine maps have been microfilmed A computerized index serves as the mechanism for retrieval of any microfilmed mine map. The operation, equipment, and index are described in the report.

Jan 1, 1974

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

By D. Harrington

The occurrence of dust in mines has always been a source of trouble, but for any years, and virtually up to the beginning of the present century, relatively little of a definite nature was known as to the numerous ill effects of dust in mining operations. Even today, with the west amount of time given and attention paid (for at least 40 years in various, countries) to research and observation en dust in mining, and in spite of the experience with it, much information remains to be obtained, before definite, well-authenticated statements can be made as to numerous features connected with the occurrence of dust in Dines an of its effect upon the health and safety of the worker. One statement that can be made with relatively good assurance of being uncontradicted in that dust is a real menace to the well-being of mine workers, and this includes both health and safety. In addition, dust in and around mines and mining plants is one cause of large financial losses to mine owners and operators. FORMATION OF DUST IN COAL MINES IN THE UNITED STATES One definition of mining is "the processes by which useful materials are obtained from the earth's crust; " since virtually all of the useful materials of or in the earth's crust either are solids or must be reached by penetrating through solids, the materials that are moved in mining must necessarily be broken or disrupted, so that almost every phase of the work of loosening the material and transporting it is likely to produce dust.

Jan 1, 1939

By J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine, Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert-system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 2010

By Graham W. Marks

This report is the fourth of a series concerning the development of spectrochemical methods for the analysis of ore samples and related Metallurgical materials by the total-energy method. In this report, the application of this method to the determination of thallium is discussed. This element lies in group III of the periodic tale; one other Clement of this group; indium, has already been investigated.

Jan 1, 1949

By Jack I. Paige

The devitrification of lithium silicate glasses was studied to determine the effect of annealing temperature, composition, and additives on nucleation and crystallization. High-purity glasses, prepared from reagent-grade chemicals, had close to optical quality when prepared by a vacuum induction melting method developed during this research, The progress of devitrification was traced by differential thermal analysis and thermal expansion for those lithium metasilicate-silica compositions containing 80 to 90 percent silica. Microscopic studies of glasses partially devitrified at various temperatures and annealing times indicated that the primary initial mode of formation of individual crystals ,vas from densely crystalline zones that filled in as crystallization advanced Of the additives tested, calcium, potassium, and sodium helped promote devitrification with the least cracking or surface deformation. Tin oxide was most effective in reducing volume contrast ion during devitrification, but was not ClS effective in preventing cracking as calcium or potassium additions.

Jan 1, 1965

By Fred D. Wright

This paper describes research at the Bureau of Mines experimental oil-shale mine at Rifle, Colo., to improve blasting techniques and reduce breaking costs. Many of the conclusions are applicable to any mining operation. Experiments Were conducted on many phases of blasting. The effectiveness of various grades of explosives was compared, and several different drill-hole patterns were tried in heading rounds. An experiment was conducted to determine the maximum effective burden for various diameter blast holes. High-speed motion-picture studies were made of blasts, and the time for initial movement of rock after detonation of the explosive was measured. Experiments with millisecond-delay detonators in heading rounds proved that, when used properly, these detonators result in improved fragmentation, economical use of explosive, and compact, easily loaded muck piles.

Jan 1, 1953

By David P. Lindroth

The objective of this research by the Bureau of Mines was to determine the technical feasibility and associated pilot data for drying minus 1/4-in coal with microwave energy at a frequency of 2.45 GHz. The drying data were obtained experimentally on three coal types: bituminous, subbituminous, and lignite. The experiments were performed with a custom-designed conveyorized microwave oven having a continuous power capability of 12 kW. Drying efficiencies near the theoretical maximum of 1.54 kg of water per kilowatt hour of energy input were achieved for two coals and two sizes; overall drying efficiencies averaged 77 pct.

Jan 1, 1986

By C. J. Johnson, C. J. Bise

"As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity.Room-and-pillar mining accounts for approximately 68% of the nations underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-mid-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.IntroductionThe ultimate goal for any coal mining company is to effectively use its human and financial resources to maximize its profits through the extraction of its reserves. Although recent workforce reductions in the industry have resulted in a more efficient use of labor and increased productivity, there comes a point in time when further reductions in the numbers of workers in each operating section are impossible with existing equipment. For example, Farinelli and Bise (1987) found that labor cost constituted 62% - 73% of the cost per ton of coal at the mining section, with a minimum crew size. Thereafter, efforts to increase productivity must focus on more efficient mine plans and technology.The fact that an increase in productivity can be realized by reducing non-productive time (change-out and tram time) and converting it to productive time has been known and demonstrated for quite some time. What has not been demonstrated frequently is the quantification of the potential productivity increase of currently emerging technology or ""add-on"" equipment. It is one thing to be able to say that a piece of equipment will make an operation more productive, but it is another thing to be able to quantify the productivity increase that will justify the purchase of the new equipment. Not only is a financial benefit possible in room-and-pillar mining with an increase in productivity, but a decrease in the time necessary to develop a longwall panel can also occur.The purpose of this paper is an analyze the impacts of a changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to several scenarios incorporating emerging technology. To do this, four cases will be developed. A base case, consisting of the typical manner in which continuous-miner sections are currently operating, is compared to three layouts incorporating: (1) flooded-bed scrubbers on radio remote-controlled continuous miners, (2)a continuous miner with side-mounted roofbolters, and (3) a continuous miner with side-mounted roofbolters used in conjunction with a continuous-haulage system."

Jan 1, 1989

By Donald P. Schlick

The Federal Coal Mine Health and Safety Act of 1969 requires each mine operator to implement the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare. This program requires frequent sampling of "high-risk" face workers and periodic sampling of other underground workers. Dust samples are collected by the coal mine operator and weighed at the Bureau's Pittsburgh Field Health Group, and the results are processed by the Bureau's Automatic Data Processing Section located in Denver, Colo. This paper presents the system employed by the Bureau to weigh the dust samples and to process and store the data.

Jan 1, 1971

By John Nagy

A study was made in the Bureau of Mines experimental coal mine of factors affecting gas ignition by a cutoff explosive charge. Experiments showed that, although gas could be ignited under some circumstances, the probability under normal mining conditions would be low. The use of permissible explosives, relatively short-delay intervals in firing adjacent holes, blasting to a 6-inch kerf, and reasonable care in the placement of the holes favor safe blasting and are current practice in mining. The experiments also showed that the weight of the charge is not a primary factor in the ignition of gas by a cutoff charge. The quenching action of a first charge on the igniting action of a second was verified in a supplementary study. Related experiments have shown that gas at the face may be ignited by a single charge of explosive when fired with a light coal burden. Permissible explosives were less hazardous under these conditions than nonpermissible explosives. The frequency of gas ignition in cutoff and single-charge experiments increased as the linear distance between the sheared face and the opposing mine rib increased.

Jan 1, 1960

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By Natalie A. Sapola, Knox Van Dyke, Jean Rabovsky, Vincent Castranova, William H. Pailes, Melanie McPeek, Deloris J. Judy

"INTRODCJCTJONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acctyl-sn-glycerol-3-phosphoryl choline) which has been shown to mediate a broad range of biological activities. 1·3 Its pulmonary actions include contraction of pulmonary tissue,4 secretion of leukotrienes from leukocytcs,5 airway constriction,6 pulmonary edema,7 and enhanced migration of neutrophils into the airspaces of thelungs.8-9PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin. 1~1 3 Therefore, PAF may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of P AF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type Il epithelial cells.METHODSIsolation of CellsNeutrophils were isolated from human blood by dextran settling and centrifugal elutriation.14 Isolated neutrophils (93% pure) were resuspended in HEPES-buffered medium (145 mM NaCl, 5 mM KCI, 10 mM HEPES, 5 mM glucose, and 1 mM CaC12; pH = 7.4). Cell number and volume were determined with an electronic cell counter equipped with a sizing attachment.Rat alveolar macrophages were obtained by pulmonary lavage with ea2+, Mg2+-free Hanks balanced salts solution. 15 Alveolar macrophages (94% pure) were resuspended in HEPES-buffered medium, counted, and sized electronically.Rat alveolar type Il cells were isolated by enzymatic digestion for 35 minutes at 37°C with 40 µ/ml type I elastasc and 0.1 % collagenase and purified by centrifugal elutriation. 16.17 Type Il cells (92 % pure) were resuspended in HEPES-buffered medium for measurement of membrane potential, oxygen consumption, and trypan blue exclusion. Type Il pneumocytcs were resuspended in 0.1 M NaCl plus 0.05 M HEPES (pH = 7.8) to measure cytochrome P450-dependent activities and aggregation. Cell size and number were determined electronically."

Jan 1, 1990

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the high funding level program plan.

Jan 1, 1980

By R. A. Cattell

With the activities of the Petroleum and Natural Gas Division geared chiefly to problems directly connected with the war effort , the emphasis of the work under oil and gas development and production was to make engineering studies of selected reservoirs for the Petroleum Administration for War , to determine the extractable quantities of components in them, and to study the characteristics of these components for use in the manufacture of aviation gasoline and other products . The needs of the Petroleum Administration for War and the operators for specific data from gas - condensate fields were fulfilled , and , in addition , engineering data along lines of a forward - looking program of research on reservoir behavior were collected , which should be of great value in the postwar period . It is planned to publish many of these data as soon as conditions permit . The work of the Secondary Recovery Section had as its objectives in- . creasing the rate of production of crude petroleum and , which is more important , preventing the premature abandonment of wells in " stripper " and marginal According to the National Survey of Stripper Wells by the National Stripper Well Association in cooperation with the Interstate Oil Compact Commission , a total of 67,460 stripper wells was abandoned from January 1 , 1935 , to July 1 , 1942 , inclusive , with an estimated loss in proved reserves of approximately 216 million barrels . This survey also indicates that over 1.2 billion barrels of oil would be recovered by primary production from more than 290,000 stripper wells then in operation , and an additional 2.5 billion barrels of oil could be recovered from them by secondary production methods . The work of the Chemistry and Refining Section was oriented towards the optimum utilization of crude oils in the manufacture of aviation fuels for spark-ignition and jet - propulsion engines . The work involved intensive studies of superfractionation , hydrocarbon analysis , and the engine testing of fuels . Particular attention was given to the effect of sulfur compounds in the crude oils and in the fuels made from them . The research on thermodynamics is concerned with the experimental determination of precise and accurate values of the fundamental thermodynamic constants of pure hydrocarbons and related compounds . The data obtained in these investigations will be utilized for devising and improving chemical processes in which petroleum hydrocarbons are the raw materials . Without such data , much time and expensive material and equipment may be wasted in attempts to obtain reactions under conditions that the laws of thermodynamics rule out of consideration . Thermodynamic data are useful and required in the petroleum industry for calculations of heat balances in the design of furnaces , fractionating towers , and heat- transfer equipment . It is of utmost importance , also , to know the heat requirements of cracking and other chemical reactions so that heat may be supplied or dissipated in the proper proportions . These needs for thermodynamic data are being recognized more and more by petroleum -refining engineers . The responsibility for the production of helium for the Navy , the Army , other governmental agencies and non-Federal users is vested in the Bureau of Mines by an Act of Congress ( 50 Stat . 885 ; 50 U.S.c. 161-166 ) . The Helium Subdivision of the Petroleum and Natural Gas Division continued to meet all demands for helium .

Jun 1, 1949

By Terry J. Close

The Anaconda Pintlar Wilderness has a significant mineral resource potential. Five deposits have resources totaling about 180,300 tons (163,600 t) containing silver, copper, lead, gold, and zinc. Another 11, not sufficiently exposed to allow resource estimates, may have additional mineral potential. No placer deposits are indicated. There is little potential for the production of sand, gravel, or stone; alternate sources are closer to markets. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By C. P. Mangelsdorf

When the finely bedded shale frequently encountered over coal seams experiences a separation, the material below the separation must behave like a beam or plate in that it must resist both bending and shear. Be-cause of the weakness in interlaminar shear inherent in such strata, shear deflections that are usually ignored in isotropic beam theory may account for a significant part of the total roof sag. Similarly, when a roof truss is installed in such a roof the upward displacement reducing the sag will have components due to shear as well as bending. Questions asked by mine operators about the installation of roof trusses frequently deal with optimum position, slope, and initial tension of the inclined chords. This Bureau of Mines report examines the effects of those chord parameters on the strain energy of both shear and bending and offers optimum values that will minimize the total strain energy of the immediate roof. Design charts are provided, several design examples are included, and the results are compared with current practice. The effects of in situ stresses are investigated and are shown to be equivalent to an additional load on the beam.

Jan 1, 1988