Search Documents

By Frank D. Lamb

Pyrophyllite, a hydrous aluminum silicate (Al2 Si4O10 (OH)2 ) has been mined in North Carolina and marketed without beneficiation for the past 100 years, but recent demands for higher-grade material indicate that an economical concentration method is needed for at least a part of the pyrophyllite production. Past production has depended upon selective mining and hand sorting, which is often unsatisfactory because of the finely disseminated character of the ores. The major impurity in North Carolina pyrophyllite ores is quartz, which accounts for the abrasiveness of the commercial product. Since pyrophyllite is only slightly heavier than quartz, those ores cannot be beneficiated by simple gravity-concentration methods. Some separation can be attained by differential grinding and air classification because of the difference in hardness of the two minerals) but the separation is not sharp. Froth flotation of pyrophyllite from Quartz has never been attempted commercially, but if the demand for high-grade material is sufficient, it would seem that this process offers the most premise of being economically feasible.

Jan 1, 1950

Continuously separate mixture of non-magnetic materials (such as scrap, precious metals, or certain ores) at a reasonable cost. Approach Nonmagnetic materials of different densities are rapidly float/sink separated by an augmented lifting force produced In a magnetic fluid (liquid) by the effect of an external magnetic field. The magnetic fluid is a colloidal suspension of magnetite In kerosene, prepared by a low-cost process. How It Works Separation is accomplished in an open trough filled with magnetic fluid. A magnetic field is established in the fluid, by energizing an electromagnet having poles on each side of the trough. Due to the design of the magnet poles and air gaps, the magnetic field is strongest at the bottom, about 10,000 oersteds, and uniformly decreases in strength to about 2,000 oersteds at the top of the fluid. Therefore, the magnetic field gradient increases with depth. The magnetic force attracts the entire separation medium (magnetic fluid) creating a reaction force of equal magnitude and acting in the opposite direction. This reaction created within a magnetic fluid/magnetic field combination is called a magnetic levitation force. It increases with the field strength. In this case because the magnetic field is strongest at the bottom of the trough, the magnetic levitation force will quickly float lighter material while heavier material sinks.

Jan 1, 1980

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By F. D. DeVaney

An examination of the physical properties of manganese ores is being made at the Mississippi. Valley Station of the United States Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Missouri. The object of the study is to find out how much these ores can be beneficiated by such processes as jigging, tabling, magnetic separation, and flotation. Some. of the results were given in an earlier report.4 Eighty samples obtained from various prospects and mines throughout the country have been examined; this is a very small part of those that should be examined before the work can be a definite factor in-the appraisal of manganese ores or the guide in beneficiation which the operators seek. The ore deposits are not expected to reach to great depths vertically, after the manner of copper and gold, but in lateral distribution their greater extent is notable. This applies particularly to the residual and replacement deposits of manganese.

Jan 1, 1929

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

A computer model of an existing mine ventilation system can be executed using data developed from ventilation survey results. This model can then be used to analyze and evaluate proposed modifications to the system. The acquisition of field measurements during a ventilation survey and the corresponding development of this information into computer input data have been discussed in detail in the preceding chapters. In this chapter, the data are used in computer-oriented analysis of the mine ventilation system. The PSU/MVS was selected for use because of its advanced capabilities. MINE DESCRIPTION The mine chosen for this application is located in Western Pennsylvania. The Pittsburgh coal seam, having an average height of 5-1/4 to 6-1/2 ft, is mined under approximately 300 to 500 ft of cover. The mine preparation plant and shipping facilities are located at the seam outcrop along a river; mining has progressed from the outcrop to an area about 10 miles from the pit mouth so that there are extensive worked-out areas through which access is maintained to the current mining area. Coal haulage is by conveyor to an underground transfer point, located four miles from the pit mouth, and then by high speed rail haulage to the preparation plant. The rail haulage link is scheduled for replacement by a conveyor in the near future. Mining at the present time is limited to the room and pillar method using continuous miners. Longwall mining had been attempted in the past with only limited success; as a result, several panels originally laid out for longwall mining are currently being extracted by room and pillar work. The

Jan 1, 1977

By R. Ward Stahl

Fire has been one of man's most useful tools through the ages and certainly is a "must" for industrial progress but when uncontrolled is one of the most destructive agencies. This fact is even more important in a coal mine, where many persons and much expensive equipment are confined in a relatively small area. Means of escape from a burning area, as well as from the products of combustion, are often limited; and in many instances the entire surroundings are combustible. Numerous mine fires, which resulted in a high death toll and great financial loss through the years, have caused mine owners to search for the best fire-fighting equipment; much of this has been installed, the quantity depending largely upon the experience of the individual companies or neighboring mines in certain coalfields. A mine owner or operator has meager published information on the actual fire protection afforded and systems of fire-fighting inaugurated in the coalfields, by which he could compare his efforts and get some idea of the adequacy of his own protection. To further general knowledge of the subject, it was decided to survey a representative number of mines in the field and show what has been accomplished. Representative mines were selected in various coal beds; some had similar tonnage, so comparison could be made if desired.

Jan 1, 1957

As a basis for recommendation and for instruction of bureau engineers the considered opinion of the bureau is expressed in "decisions" of its Mine Safety Board, approved by the Director. Ten of these decisions were discussed, in Information Circular 6091.3 Decision No. 11, approved by Scott Turner, Director, on February 28, 1929, is as follows: "In the interest of safety, the Bureau of Mines, Department of. Commerce, recommends that in coal mines, haulage and (or) hoisting be kept in intake air as far as possible." As in the case of previous mine-safety decisions, the subject matter covered by this decision has frequently come to the attention of the Bureau of Mines through the reports of its mining engineers on explosion disasters and in accident-hazard investigations.

Jan 1, 1929

Provide coal mine shafts/slopes with an optimum coal mine shaft fire and smoke protection system composed of reasonably-priced, reliable hardware. Approach Accident and injury data indicate that a relatively low percentage (5%) of underground coal mine fires occur in shafts or slopes. Nevertheless, shaft or slope fires are extremely serious because they block critical escape routes for miners. That also can happen when combustion products resulting from fires in other mine areas contaminate shahs and slopes. Seeking the optimum configuration for a shaft/slope fire and smoke protection systems, the Bureau of Mines gathered data on the performance of existing fire detection devices and signal telemetry systems In several mines, and analyzed the generic protection needs of the U.S. underground coal mining industry. The optimum system developed by the Bureau provided an adequate number of detectors, a wide area of coverage, and an extensive data acquisition, analysis, display, and storage capability. This system. recommended for fabrication and in-mine testing, consisted of a microcomputer-controlled master panel located in the test mine's slope hoist room, and four remote units. Two of the remote units were placed on the surface atop upcast ventilation shafts, a third was situated underground near the slope bottom, and a fourth was installed at the slope top in intake air.

Jan 1, 1986

By Ivan F. Avery

PRODUCTION of carbon black decreased 4 percent in 1961. Output in the major producing States of Texas and Louisiana decreased 1 percent and 8 percent, respectively. Production of channel black continued downward, declining 10 percent in 1961 compared with 9 percent in 1960. Furnace black production also decreased 3 percent from 1960. Total domestic sales, however, increased 2 percent, Sales to most major consumers increased, but sales to the ink industry decreased 10 percent. Producer's stocks decreased 5,083,000 pounds during the year. Exports decreased 4 percent. SCOPE OF REPORT Carbon black is a very pure grade of quasi-graphitic carbon; particle diameters range from 50 to 5,000 angstrom units. Annual reports were submitted to the Bureau of Mines by operators of all commercial plants in the United States.

Jan 1, 1962

By Jeffrey B. Osmint

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1991

By E. D. Calvert

As part of its goal to minimize the requirements for critical and strategic minerals, the Bureau of Mines is conducting research to foster the use of domestically abundant materials such as molybdenum. This report describes the development of an investment shell molding technique that can be used to make castings of molybdenum and its alloys. The mold material is cubic Zr02 with a monoclinic Zr02 binder. The shell, formed by standard investment molding techniques described in the text, is prepared for molybdenum casting by firing for 6 hours at 1,550° C (2,822° F) or for 4 hours at 1,650° C (3,002° F). The resulting castings have predictable and reproducible dimensions with good detail. As-cast strength is poorer than the strength of wrought materials below 1,600° F. At and above this temperature, tensile strengths of cast and wrought materials are nearly equal. Aqueous corrosion of the castings in most media is insignificant.

Jan 1, 1982

By A. W. Khair, S. J. Jung

"A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.1. INTRODUCTIONMuch research in the past has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in cutting process. However the mechanisms of energy dissipation or failure criteria for rocks in cutting process in order to evaluate the efficiency of energy requirements in specific rock fragmentation is not well understood. The formation of a crater in rock under the impact blow of a bit has been observed experimentally (Hartman, 1959). It is known that directly beneath the edge of the bit the rock is crushed into fine powder, toward the sides of the crater it chips out into relatively large fragments. (Sikarskie & Cheatham, 1973). Singh et al. (1967) investigated the cratering process under the two different conditions of static and dynamic loading. They found that the amount of energy consumed per unit volume of crater is unequal for the two different loading conditions. A complex network of fractures often extends downward and laterally into the rock below the bit. The surface of the specimens showed that the dynamic loading damaged larger area then the static loading."

Jan 1, 1989

By Andrew B. Cecala, Edward D. Thimons

"The Bureau of Mines has recorded a number of different background dust sources that significantly contaminated the air breathed by bag machine operators. These background sources, observed at five different plants over the past 2 years, can expose bag machine operators to more significant dust concentrations than the filling process itself. To keep bag operator exposure within acceptable dust levels established by the Mine Safety and Health Administration, U.S. Department of Labor, the significance of these background sources must be realized, and the sources must be identified and controlled. The purpose of this work is to identify common background dust sources and show the significant effects that they have on the bag operator's overall dust exposure. INTRODUCTIONThe purpose of this report is to identify some common background dust sources in and around the bag-filling area. Although these background dust sources are of ten unrecognized, they can be more significant sources of contamination than the dust generated from the bagging process.The bagging of mineral products into 50- and 100-lb paper bags is common throughout the entire mineral processing industry. Bagging is performed by a bag operator who sits in front of a two- or four-station fill machine. The bagger's function is to attach empty bags to the fill nozzles as filled bags are ejected from the machine. If the product being bagged is extremely fine (smaller than 200 mesh), the bag operator's dust exposure is usually one of the highest in the plant.The bag operator is exposed to two primary dust sources. The first is product blowback during the bag-filling cycle. This occurs as excess pressure is released from around the fill nozzle during filling. As the excess air forces its way out of the bag, product is forced out with it. This blowback of product leaving the bag creates a considerable amount of dust. The second major source is the ""rooster tail"" of product thrown from the bag valve and fill nozzle as the bag is ejected from the fill machine. Since the bag is pressurized as it leaves the machine, product spews out of the valve for a few seconds."

Jan 1, 1986

By H. K. Kutter

The pressure pulse generated by an underwater spark \vas investigated in relation to its potential use for rock fragmentation. The study established (1) the relation between the peak discharge current and the peak wave pressure; (2) the relationships among the peak wave pressure, the discharge voltage, and the spark gap width; (3) the type and pulse duration of the generated wave; (4) the percentage of energy transmitted in the spark as a function of spark gap width and discharge voltage; and (5) the percentage of energy converted into the pressure wave as a function of gap width and discharge voltage. Spark-generated fractures were studied in two-and three-dimensional rock and plastic specimens. The laboratory results indicated that the pressure pulse generated by an underwater spark is a potential practical tool for rock fragmentation. The paper contains an appendix describing the capacitive pressure gage specially developed for the laboratory tests.

Jan 1, 1969

By A. W. Khair, S. J. Jung

"IntroductionIn a typical incremental loading test, the AE activity increases rapidly in the initial stage of the loading. It is associated with initial closure under compression of favorably oriented cracks already present, together with sliding of crack faces against each other /1/. After the initial stage, crack closure and movement largely cease and the AE activity drops to a barely detectable level /2/. In the final stage of loading test, cracking associated with the onset of inelastic deformation' occurs, and the rate of AE rapidly increases /3/ indicating an increase in the •number of events associated with higher number of microcracks. To understand better primary fragmentation process, Anderson and Ruzzi conducted tests to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool /4/. They proved that a relationship existed between the AE activity, generated during fracturing and the amount of fracture surface area created.A process of fragmentation, demonstrated by conical bits acting orthogonal to the flat surface of block of coal specimen with and without lateral confining pressure is presented here. The monitoring of AE during the fracturing process of rock/coal has been a very useful indirect method in studying fracture mechanism.Specimen PreparationLarge blocks of Waynesburg coal were obtained from a surface mine. These blocks were then out and molded to approximate dimensions of 25.4 x 25.4 x 15.2 'an (10 x 10 x 6 in.). These specimens were instrumented with three strain gages in a 45 degree rosette. One was mounted parallel to the bedding plane direction, another was tinted at an angle of 45 degree from the bedding plane direction and the third was mounted perpendicular to the bedding .plane direction. Each of the three strain gages were set 5.1 an (2 in.) away from the impact point.Typical Test ProcedureIn a typical experiment, the specimen was placed in the confining chamber.Predetermined equivalent in-situ stresses were applied to the specimen by using two sets of hydraulic cylinders. Two 1 in. thick steel plates ware positioned between the sample and the hydraulic cylinders in order to distribute the pressure uniformly over the whole surface of the specimen. The LVDT null position was adjusted with respect to the coal face. After setting the LVDT, the bit and associated weight was lifted to a predetermined height (equivalent to a predetermined kinetic energy) by a win. The three strain gages were balanced using the signal conditioner and the output was recorded by a 6 channel strip chart recorder. The experimental set-up is shown in Figure 1."

Jan 1, 1989

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By C. E. Wethered

This paper describing the mining methods employed by the Federal Mining and Smelting Co., operating the Morning mine at Mullan, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The daily tonnage produced at the Morning mine, including that mined by leasers, is 1,100 tons. Mine run of ore will average 9.1 per cent lead, 5.8 per cent zinc, and 4.4 ounces silver per ton. A stull set and fill method of mining is employed.

Jan 1, 1930

By F. W. Hoertel

Tungsten from the hydrogen reduction of WF was vapor - deposited to coat MERM (Material Evaluation Rocket Motor ) graphite and rhenium- lined graphite nozzles . These nozzles have surface configurations that preclude the conventional fabrication of high- density- tungsten liners . Operation at 550 ° C produced selectively placed uniform coatings of specified thicknesses at near theoretical density . An acceptable coating could not be deposited on a beryllia nozzle because of an undesirable side reaction between the substrate and one or more of the products of the reduction reaction .

Jan 1, 1964

By H. H. Schrenk

The safe use of a refrigerant or any substance depends on knowledge of its pertinent properties and conditions of use; therefore some of the properties of refrigerants that are related to life, fire, and explosion hazards are discussed herein. These data serve as a basis for suggested control measures in the use· of refrigerants. The properties of refrigerants may be broadly classified into three main groups: (1) Those important for refrigeration, (2) those significant from the standpoint of confining the refrigerant, and (3) those that become important if the refrigerant escapes from the :machine or container. The first group of properties, such as latent heat of vaporization, specific heat of vapor, specific heat of liquid, etc., is not considered to be directly related to safety and is not discussed here. The second group, those properties important in confining the refrigerants, has particular significance because· it relates to "built-in" safety. This group is emphasized because it is believed the soundest procedure in designing equipment is to give due consideration .to both the health and safety hazards likely to be associated with the equipment. Furthermore, the toxicity, fire, and explosion hazards are controlled as long as the refrigerant is confined. Some properties of this group are (1) stability, (2) corrosiveness, (3) boiling point, (4) pressure developed in the system, (5) warning odor or irritation, and (6) ease of detection. The third group includes such properties as toxicity (of compound and decomposition products), irritating action, and explosibility.

Feb 1, 1942