Search Documents

By H. E. Blake

An evaluation was made to determine the economics of utilizing waste fluosilicic acid for production of (1) calcium fluoride, and (2) anhydrous hydro-gen fluoride. Two versions of each process were considered and compared. The evaluation showed that both products could be produced and marketed competitively. Lowest estimated product sales prices required to yield a 25-percent return on investment before taxes (discounted cash flow basis) was $339.34 per ton of hydrogen fluoride and $48.64 per ton of calcium fluoride.

Jan 1, 1971

By Oliver W. Keener

The operation described herein differs from the usual practice in the Tri-State district in two important respects: (1) the ore is loaded into cars which are tramped to the shaft and hoisted on self-dumping cages, and (2) about 30 per cent of the ore is loaded by power shovels. The four-month period covered by the cost data appended at the end of the paper immediately followed a period of about one year during which the mine was shut down, and the expense incident to the resumption of operations is reflected in the costs. The author acknowledges the assistance of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the preparation of this paper and the compilation of the data.

Jan 1, 1929

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

By Herbert H. Fields

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (1), and pipeline--quality gas was introduced into a commercial pipe-line. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed,

Jan 1, 1975

By T. C. Higgins, J. S. Malesky, J. A. O'Connor

"INTRODUCTION This circular contains the story of a stubborn mine fire of electrical origin that started on the main haulage road of No. 59 mine of the Peabody Coal Co. and illustrates that sometimes serious fires can be fought by direct attack. The story also points out that the cost of such procedure can be extremely high, and it is better, therefore, to minimize the possibility of a fire of electrical origin by suitable over-current and line-fault protection. The lives of 163 men were saved by utilizing a recently sunk air shaft near active workings as an escapeway. These men could not have reached the older openings. Also described are the rescue of 75 additional men through another air shaft, sealing of the fire, attempted extin¬guishment with carbon dioxide, and the difficulties of fighting the fire and recovering the mine.A fire occurred shortly before 12 o'clock noon, August 15, 1949, in the No. 59 mine, Peabody Coal Co., Springfield, Ill. All 257 men underground escaped to the surface. One group of 75 men was delayed from escaping for several hours after the alarm was given because smoke and fire gases were circulating in a main return airway, which intervened between their working section and one air shaft, and also in the stairway compartment of the shaft. After being supplied with universal-type gas masks, or self-rescuers, these men were conducted from the mine by members of a State mine-rescue team and other mine employees. Six nine officials were hospitalized because of exposure to carbon monoxide during fire-fighting activities; all were discharged a few days afterward. Later, while doing work incident to fighting the fire, two men were killed, and several were injured by falls of roof and rib.The fire broke out after a collision of a loaded trip with four empty mine cars on the main east haulage entry. The mine cars were jammed against the trolley wire causing a sustained electric arc that ignited the wooden mine cars and the fire spread to the timbers and coal."

Apr 1, 1950

By Vernon R. Miller

The Bureau of Mines developed and evaluated a detector-sorting device to separate the copper-bearing portion from the barren portion of native copper ores. Small-scale sorting tests were run on minus 1-inch plus 1/2-inch size materials from the following Michigan samples: Winona, Kingston, and Centennial ores, and "poor" rock from the Champion mine dump. Results showed that 60 to 85 pct of the copper was recovered in 9 to 19 wt-pct of the sorted fraction. About 90 pct of the copper recovered was obtained in the first pass through the sorter. For the Kingston and Centennial ores, combinations of sorter concentrates and fines generated during crushing, resulted in recoveries of 93 and 94 pct, respectively, of the total copper in the samples. The combined products constituted about 66 wt-pct of the total sample and allowed the balance to be discarded with only a 6 to 7 pct copper loss.

Jan 1, 1974

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By N. A. C. Smith

During the past, six, years, the Bureau of Mines has made and. published several hundred analyses of typical crude oils and 'has developed a system of interpreting the analyses and of classifying crudes. This system is presented here with. It is apparently equate for classifying crude oils into four main groups and has also been found very convenient in studying the geological relationships between crude oils, and the probable refinery yields of valuable products from them. Crude petroleum is morn to be a very complex substance. An analytical statement of its properties must, therefore, consist of two distinct parts, - first, the report of the results of the determinations made by the analyst in the laboratory, - second, the proper arrangement, classification and interpretation of these results so that the analysis, as a mole, will indicate the meaning- and the relative- importance of the essential characteristics of the oil.

Jan 1, 1927

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By Stephen Utter

This report summarizes the procedure and results of an investigation to determine the stresses in the rock around an underground opening in the Climax molybdenum mine, Climax, Colo. This study is part of an overall investigation conducted by the Bureau of Mines to determine the stresses induced by block-caving mining. The purpose of this study is to obtain estimates of the magnitudes and directions of the principal stresses, the location of the maximum stress concentrations, and the effect of topography on the stresses.

Jan 1, 1962

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By W. D. Bensema, J. W. Adams, W. W. Scott, H. Dobroski

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the en- tire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 10, 1974

By R. E. Perry

In connection with a program of coal research at the Southern Experiment Station the Bureau of Mines, in cooperation with the University of Alabama and the various coal operators, conducts washability studies of coal from beds in Alabama and other Southern States in which commercially important deposits occur. One of the main objectives of a washability study is to obtain technically and commercially important data necessary for determining the best methods for preparing and utilizing the Nation's limited reserves of coking coal. Such information is important to conservation because it facilitates selection of preparation methods that will provide maximum yields of coal with low ash and sulfur contents.

Jan 1, 1958

By C. Melvin Lepper

A solid-state amplifier for the bridge circuit of an atomic-absorption mercury detector is presented and described. Operational advantages over previously used circuitry include improved time and temperature stability, increased measurement accuracy, and simplified setup, calibration, and operation.

Jan 1, 1972

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By W. A. Calhoun

A method for concentration of the nickel-cobalt-bearing mineral, siegenite, from a table middling has been developed by the Bureau of Mines at Rolla, Mo. The table middling is composed of a complex series of sulfide minerals, occurring in mill operations in the southeast Missouri "lead belt." In these operations the siegenite is lost as a separate concentrate, being diverted to other products. The procedure also includes recovering commercial-grade concentrates of copper and lead. A low-grade zinc concentrate, a potential coproduct, was also made.

Jan 1, 1962

By Kung-Lee Wang

The 1963 performance of the United States economy was impressive. The year was one of continued growth unmarred by a recession. By the end of 1963 the economy's expansion had already lasted almost as long as the 1954-57 upswing, and the net gain in output since the trough in activity in early 1961 compared favorably with most earlier postwar cyclical advances. There was no indication of any slow- down at yearend. Both gross national product (GNP) and national income in 1963 were 5 percent higher than in the previous year. GNP totaled $584 billion, a gain of $28 billion over 1962. Real output of goods and services rose 3.4 percent over the year. Price increases continued to be moderate. Production, employment, personal income, and corporate profits all registered new but unemployment continued high at 5.5 percent and the prospects for improvement remained poor. The economy again failed to use its full potential. Current value of mineral production kept pace with the economy. The constant dollar value of mineral production gained more than real GNP because of the relatively stable price of minerals. Mining production achieved a new high in 1963. Steel production totaled 110 million tons, 12 million tons above 1962, making 1963 the first 100- million-ton year since 1957 and lifting the steel-associated minerals group upward. The gain in ferrous metals mining was insufficient to compensate for the decline of nonferrous metals mining resulting in an insignificant decline in the metal mining total as a whole. The upsurge of construction material minerals output, with an assist from chemical and fertilizer minerals, accounted for peak production of

Jan 1, 1964

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By Robert D. Schmidt

This Bureau of Mines report describes the development and application of a computer model for simulating the hydrological activity associated with in situ leaching. The model is intended to provide uranium resource developers with a description of the flow behavior of leachants and ground water during the development, production, and restoration phases of a leaching operation involving an arbitrary pattern of injection and recovery wells. Different aquifer environments are modeled, using a closed-form solution to the partial differential equation that describes three-dimensional changes in piezometric head as a result of pumping from leachant injection and recovery wells. The computer program can model a maximum of, 50 arbitarily located wells. Numerical techniques involving difference quotients and Taylor expansions about time points are used to derive time, velocity, areal sweep, and fluid volume parameters associated with leaching hydraulics. These parameters are output by the program in graphic and tabular formats. Other numeric methods insure that the program running time is minimized without significantly affect-ing the accuracy of results.

Jan 1, 1980

By William C. Larson

A study was conducted by the Bureau of Mines to provide quarry operators with information regarding (1) the effects of jointing and bedding on rock fragmentation when bench blasting in two small-scale (2.5-ft) limestone benches, and (2) the successful use of inexpensive equipment and field techniques to determine the orientation and spacing of joints and bedding separations within the quarry. Using inexpensive equipment, such as a pocket transit and steel and paper tapes, joint and bedding separations were mapped and their frequencies measured. Results from two small-scale bench blasts in the Stewartville member of the Galena limestone formation showed that when the row of vertical blast-holes was oblique to the vertical joint orientations, the backface expression was outlined by two relatively large triangular protrusions (joint surfaces). In this blast, part of the rock burden was unbroken. When the line of vertical blastholes paralleled a predominant joint set, all of the rock burden was broken and displaced. The thickness of fragments that had been displaced by a blast correlated with the observed bedding thickness in the bench.

Jan 1, 1974