Search Documents

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS© Expert system together with three VisioRockTM online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS© is the first installation to incorporate Metso Minerals Process Technology-Asia Pacific's (MMPT AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS© logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

By J-N. Oyourou, R. McCrindle, C. J. S. Fourie

"Many mines in South Africa were inappropriately closed and left unattended during the last century. These old mines are potential sources of environmental pollution and may pose a health risk to local populations, since the surrounds contain elevated levels of toxic elements. Soil from the old Edendale lead mine property in Mamelodi Extension 11, east of Pretoria, which was suspected to be contaminated with lead, was analysed. The mine, which primarily extracted galena, was decommissioned in 1938. During this study, the old mine property and surrounds were screened for zinc and lead using a field-portable X-ray fluorescence (pXRF) spectrometer. The metal concentrations, which ranged from 18 to 7 300 mg/kg for zinc and from 50 to 21 000 mg/kg, for lead, were plotted together with the GPS coordinates to produce a concentration distribution map for lead and zinc. This map revealed three anomalies of unacceptably high concentrations, possibly corresponding to areas where ore had been piled or dumped to waste from the old mine. Thirty-six of the soil samples that were analysed by pXRF on site were selected and analysed in the laboratory using inductively coupled plasmaoptical emission spectrometry (ICP-OES) for verification purposes. The zinc and lead concentrations obtained from the two analytical methods were compared using linear regression analysis. Excellent correlation was obtained between the results from the two methods (r2 = 0.99 for zinc and r2 = 0.95 for lead). IntroductionEarly economic development in South Africa was based mainly on mining. However, these activities left a legacy of approximately 6 000 improperly closed mines scattered throughout the country (SAI, 2009; van Schie, 2012). Due to their proximity to settlements, these abandoned mines may pose a potential health risk to humans and an environmental hazard. Mining activities generate large amounts of waste, mostly in the form of overburden and process tailings, which often contain high concentrations of toxic elements. Bioavailable toxic elements can contaminate crops growing in the polluted area (Kala, 2010; Marwa, Meharg, and Rice, 2012) or eventually migrate and detrimentally affect the groundwater (Rösner and van Schalkwyk, 2000). Moreover, sulfides accumulated in mine waste generate acid minewater (Rösner and van Schalkwyk 2000). Unfortunately, owners of mines, closed before the promulgation of the Minerals Act more than twenty years ago (Act 50 of 1991), avoided the compulsory rehabilitation of the environment enforced by this legislation. Toxic elements, such as lead, which were confined within ores, may become exposed through mining and are therefore more easily mobilized within the environment. Elements essential to human and plant metabolism, such as zinc, when exposed by mining activities, may become hazardous due to elevated concentrations (Aslibekan and Moles, 2003; Wuana and Okiemen, 2011). Humans exposed to potentially toxic metals may experience harmful effects as discussed elsewhere (Nriagu and Pacynar, 1988; Wayne and Ming-Ho, 2005)."

Jan 1, 2019

By C. G. Carey, M. P. Mullins

BHPBilliton is a large (US$32bn market capitalization) diversified mining group. Significant organic growth is planned through the development of a number of mining, processing and oil and gas projects, totalling some US$5.2bn over the next three years. The investment standards underpin the capital approval process, and incorporate the requirements for range and risk analysis of key input variables, including mineral resources. Public reporting codes for mineral resources and ore reserves (such as JORC) stipulate deterministic reporting of estimates, but are generally silent on any requirement for range or risk assessment, although they acknowledge the risk and uncertainty in the production of resource estimates. In contrast, public reporting of petroleum reserves allow for the use of either deterministic or probabilistic estimation, and for the latter, mandate the level of confidence required for proven versus probable reserves. Conditional simulation techniques, popular in the petroleum industry, provide an ideal tool forrange and risk assessment of the range of outcomes of key resource parameters, such as tonnagesand grades. Examples of a diamond deposit and of a porphyry copper deposit are presented. The understanding and quantification of mineral resource risk through a technique such as conditional simulation provides quantified information on the potential upside or downside. These techniques should be more widely utilized in the high-risk minerals extraction industry. Keywords: mineral resources, conditional simulation, risk, capital investment standards, BHPBilliton.

Jan 1, 2003

To determine the characteristics of a mineral deposit, the usual practice is to take samples, analyse the properties of those samples and infer the characteristics of the deposit from these properties. This analysis can be done using statistical methods. In the present work we are concerned with two types of statistical approaches, classical statistics and spatial statistics. If one uses classical statistics to represent the properties of the sample values, the assumption is made that the values are realizations of a random variable. The relative positions of the samples are ignored, and it is assumed that all sample values in the mineral deposit have an equal probability of being selected. The likely presence of trends, zones of enrichment, or pay shoots in the mineralization, is ignored. The fact that two samples taken close to each other are more likely to have similar values than if taken far apart is also not taken into consideration. In contrast, spatial statistics will be used if one chooses to consider that the sample values are realizations of random functions. On this hypothesis, the value of a sample is a function of its position in the mineralization of the deposit, and the relative position of the samples is taken into consideration. The similarity between sample values is quantified as a function of the distance between samples and this relationship represents the foundation of spatial statistics. There are few situations where classical statistics can be used. The assumption that all sample values in the mineral deposit have an equal likelihood of being represented will be satisfied only if the sample values are randomly distributed, or if the sample positions are random. Sample values are in fact never randomly distributed within a mineral deposit. Further- more, geologists usually avoid taking samples at random (random sampling), as it is correctly accepted that samples located on a regular grid, or approximately on a regular grid, give more information than randomly located samples. In practice, classical statistics should be used only in the early stages of exploration, when the number of samples available is relatively small and the distances between samples are large. In these circumstances, and whenever the information available is not sufficient to permit the use of spatial statistics, application of the methods described in this chapter is justified.

Jan 1, 1978

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009

By A. Holder

A major mud push occurred on the 870 m production level, scraper drift block cave at Dutoitspan diamond mine in November 2011, during which it is estimated that more than 4 400 m3 of mud engulfed the west cave. The production level was successfully evacuated during the mud push with no loss of life or injury to personnel, thanks largely to mine employees being well trained in and adhering to on-mine mud rush evacuation procedures. All access to the west cave was lost as a result of the mud push. Clean-up operations are currently under way to regain access to the production level, to establish the extent of damage to scraper drifts and equipment, and to evaluate what remedial works may be required to resume production. The magnitude of the Dutoitspan mud push necessitated a detailed investigation into the key contributing factors leading up to the incident, which are discussed in this paper. Mud rush mitigation measures in place on scraper drift block caving operations at Dutoitspan, Bultfontein, and Wesselton diamond mines in the Kimberley area are critically reviewed. Recommendations are furthermore made for enhanced mitigation based on mud rush risk profiles derived for different production areas in these old scraper drift block caves. Keywords mud push, mud rush, scraper drift, block cave, mitigation factors, risk profiles, risk management structure.

Jul 1, 2013

By André Fouché

GFWW Bulk Sample Prep Plant INDEX ?Features ?Flow Diagram ?Pictures of Plant

Jan 1, 2005

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in1983 with the formation of De Beers Marine. Full-scale commercial mining commenced around 1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geo-survey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. DeBeers operates across the entire value-chain spectrum from geology and geo-survey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in DeBeers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities are also available to support R&D and projects activities. Hydro transport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet-pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By W van Drunick, S Naik

To date, Anglo Research has carried out several projects, based on the techniques developed in the AMIRA P9 (AMIRA International Limited), to develop comminution and flotation models for several Anglo Base Metals and, to a lesser degree, Anglo Platinum flotation plants. Plant optimization is thus achieved through steady-state sampling, model-fitting and simulation using the JK SimMet and JK SimFloat software packages. The surveys can vary depending on the needs of the plant/client. The survey can therefore include as little as a single piece of equipment, an entire milling/flotation circuit, or a complete circuit from primary comminution to final flotation concentrate (i.e. the ?integrated survey?). The presence of the AR team on-site usually precipitates in face-value observations that can lead to initial improvements. This stems from the knowledge-sharing on best practice that exists in parallel with the surveys. Numerous (reasonable) changes can then be simulated, thus indicating the optimization step most likely to result in the best efficiency improvements. The simulations can include changes in the flowsheet, ore characteristics, mill loads, grinding media size, change in grind, flotation residence time, air hold-up and several more. Plant surveys can result in process changes that provide the plant with either: higher plant tonnage, improved plant grind, additional flotation recovery and/or improved product grade. The additional benefit of performing an integrated plant survey is that the effects of an optimization change in the comminution circuit can be simulated using the flotation model. This paper describes a number of case studies where individual and integrated plant surveys were conducted by AR for Anglo Base Metals.

Jan 1, 2007

By A. Hoogervorst

Cyanide is a key contributor to the efficiency of gold extraction. Public perceptions of cyanide are emotive and following some publicised incidents involving cyanide, the gold mining industry established a voluntary cyanide code for the manufacture, transport and use of cyanide in the production of gold. The paper describes the development of the code, its content and the third party auditing of the code as a means of establishing and maintaining benchmark standards. In adhering to the cyanide code requirements, there are overlaps with other management systems such as ISO 14001 and OHASA 18001 and the paper seeks to show how existing mine systems can readily accommodate cyanide code compliance and that operating and auditing the cyanide code can assist in the integration of mine heath, safety and environmental management systems.

Jan 1, 2009

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By J. C. R. van Schoor

In this study the applicability of a batch press to predict the energy consumption and particle size distributions for medium-pressure roller presses was investigated. The relationships between energy consumption, feed size and product size are discussed with reference to Hukki?s interpretation of Bond?s and Rittinger?s laws, as well as the particle size parameter used. It was found that the comminution laws have limited utility for the characterization of the performance of the medium-pressure roller crushers or the batch press used, and also depend on the particle size distribution indicator used. It was also found that the batch press is not a suitable simulator for medium-pressure roller mills as it was notable to predict the energy requirements, or to predict the size distributions that would be obtained for the ores evaluated.

Jan 1, 2012

It is well understood that to develop wagon wheels with higher abrasion resistance, fracture toughness, and fatigue resistance, steels with lower amounts of inclusions need to be used. Clean steels are produced with technologies that minimize the amount of inclusions in the microstructure. The demand for cleaner steels is high, and lowering of non-metallic oxide inclusions and controlling their morphology, composition, and size distribution is vital. Reduction of residual impurity elements such as sulphur, phosphorus, hydrogen, nitrogen, and trace elements is essential in the production of cleaner steel. Material cleanliness is vital for fatigue endurance, since oxide inclusions may act as stress concentrators and initiation points for fatigue cracks. To better understand the relationship between the cleanliness and toughness of the 34-inch cast wagon wheels, two samples of different levels of cleanliness were supplied for investigation. This paper presents the results of metallurgical analysis using scanning electron microscopy(SEM), energy-dispersive spectrometry (EDS), and mechanical tests for the pearlitic high-performance cast rail wagon wheel (identified as Class B) that are currently being used. The Charpy V-notch impact test results for the three samples from wagon wheels were compared. With the aid of SEM/EDS analysis system, non-metallic inclusions in these steels were detected, and it was possible to determine the position, size, shape, and composition of each particle. Alumina and manganese sulphide inclusions could be identified as the dominant inclusion types in the investigated samples. Fracture surface analysis of the Charpy specimen with high inclusions indicated that transgranular cleavage was the predominant fracture mode. Fractography of fracture surfaces of Charpy impact test samples also showed improvement of toughness properties on the clean sample.

Jan 1, 2013

By E. J. McLean

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By D. J. Stanton

The objective of this study was to develop, install, and test a small underground mobile refrigeration plant (MRP) to deal with some of the real problems associated with mine cooling in an operating mine. The requirement for cooling the underground environment is discussed with particular emphasis on the need for this method of cooling, with the concomitant benefits. The research investigated current methods of cooling and reasons for previous failures in MRP. Both static and dynamic simulations were conducted to increase the confidence level under operating conditions. Implementation and testing, resulted in ?lessons learnt? requiring modifications, which are documented. Actual results have been recorded. These results have proved that significant cooling via MRP is feasible. Main benefits include positional efficiency, cost per kilowatt of cooling and cooling opportunities for remote hot areas of a mine. Finally, a proven technology is now available for large-scale implementation in the mining industry. Now the ventilation engineer has another system of cooling, which can be utilized in the quest to create an occupational environment, which meets the physical and mental health requirements of the worker.

Jan 1, 2004