Search Documents

By C. A. Snyders

The research presented in this paper investigated the practical aspects of the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were conducted on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of Pt, Pd, and Au were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours, and 100 per cent for Pt, 97.4 per cent for Pd, and 99.9 per cent for Au after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while Ni concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, Ni adsorbs at approximately the same rate as the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. The equilibrium loading of gold is exothermic in nature (Fleming and Nicol, 1984) which will result in an increase in gold elution kinetics with an increase in temperature at similar pre-treatment conditions. A similar result was found for the elution of Pt and Pd. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and results suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing due to increased ionic strength.

Jan 1, 2013

By H. Cevizci

In this study, a newly developed plaster stemming method is studied and compared with the usual dry drill cuttings stemming method for surface blasting in mines and quarries. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. In one series of blast tests, blasting costs per unit volume of rock were reduced to 16 per cent by increasing burden and spacing distances. Also, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments reduced to 5.4 per cent of the total, compared to 37.7 per cent in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage, but these increased values were small and under the permitted limit for blast damage criteria.

Jan 1, 2012

By Peter N. Calder, Alan Bauer

The complexity of modem open pit load-haul-dump systems is described, and the need for realistic working models is pointed out. Both standard and probabilistic simulation procedures are discussed, probabilistic simulation being indicated as the more powerful and practical technique. Acquisition of the necessary pit operating data required for simulator construction and general modelling procedures are described. Finally, results from a typical open pit simulator are used to indicate the scope of the technique.

Jan 1, 2014

By FJ Fourie

Lack of success in attempts to develop viable large-scale continuous mining techniques (previously reported by MP o?Hare in 2004) led the team at Kopanang to explore alternative solutions to their ongoing need for improved profitability. By calling into question the basic assumptions around the stoping of narrow tabular deposits of gold, fragmentation and more particularly, the range of sizes of blasted rocks eventually became the focus of serious study. This background is briefly covered before the sequence of the investigations is described. So far, some of the ?rules of thumb? derived over the years have been confirmed, albeit for totally different reasons than those from which they arose; some persistent theories on gold loss have been debunked, and some new ones have been developed. Blast optimisation (the means by which desired fragmentation is achieved) has been based on tailoring energy to rock characteristics in an innovative packaging design for explosive charges. Other beneficial consequences arising from the work include increased production volume and gold output, a decrease in milling consumables, and the Mine Call Factor is being maintained at a level previously thought to be unachievable. This is very much a ?work in progress?, and it is empirical in its approach. The authors are the first to recognise that they have yet to determine in absolute measures why some of the innovations have had the effect that has been observed. Also that there other factors which may contribute to the result, but which have not yet been examined. Nevertheless, publication of the work completed so far is felt to be justified; firstly on the basis of the achievements themselves, and secondly for the benefit of others in the industry for whom similar problems exist. Statistical reports of the effects on the business are included at the end of the report. Detailed laboratory test results have been separated into an appendix, leaving salient graph and tabulated data in the main text. For ease of reading, units of measurement for particle sizes below 1mm are described in microns, but millimetres have been retained for those at that size or greater.

Jan 1, 2007

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008

A decision by joint-venture partners Anglo American, Gencor, and the Industrial Development Corporation to proceed with the expansion of the Columbus Stainless Steel plant in Middelburg will contribute significantly towards the economic growth that South Africa needs so desperately. The expanded facility, expected to come on-line in 1995, will be the largest single-plant producer of stainless steel in the world, and the company will rank sixth overall in world production.

Jan 1, 1993

"Chairman: Dr DeV. HarrisRapporteur: Mr A.H. MunroPapers:Corporate exploration strategies by MacKenzie, B.W.The Engel Simulator and the search for uranium by Griffiths, J.C. and Singer, D.A.The Chairman opened the session by tracing the changes which have taken place in the exploration field since the days of the lone prospector who relied upon his individual skills and to a large extent on luck. The deposits which now remain to be discovered are better covered and are of lower grade. A much greater team effort, involving geoscientists and engineers, is required. The gamble is thus much greater -not only are the probabilities of failure still significant but the consequences are more severe. A recent Canadian survey indicated that expenditures of between two and nine million dollars on regional exploration programs are required to locate one significant deposit.The Chairman went on to say that these facts have led companies to regard exploration as another form of investment and to treat it accordingly. This had placed exploration in the context of corporate strategics and structures, which was the subject of the first paper of the session.In introducing his paper, Dr B. W. MacKenzie said that the paper suggested a decision framework for exploration planning. Initially the environment is analyzed to define observable and relevant economic characteristics. The terms of reference for exploration planning and the appropriate allocation of capital and skills are then established in the light of corporate objectives and growth alternatives. With the aid of this information and in the light of profit and corporate risk criteria, exploration strategies can be selected.Dr MacKenzie went on to say that the usefulness of the concept and criteria outlined in his paper depended critically upon three characteristics of any particular economic environment, namely, the return resulting from an economic discovery, the unit discovery Cost and the probability of making an economic discovery. He then showed by means of a case history relative to the Canadian Shield and Cordilleran areas that these three characteristics could, in fact, be evaluated for regions with reasonable histories of mineral activity.The first contributor to the discussion of the paper, Mr Alfred Weiss, mentioned that his group had been involved in exploration modelling for some ten years and were thus particularly interested in the paper. He went on to say that they had experienced greatest difficulty with reconnaissance programs and that he sensed that these difficulties were also present with the methodology which had been outlined. Mr Weiss asked Dr MacKenzie how he would deal with such situations when no information was available but where there was the potential for both exploration and discovery. Dr Mackenzie agreed that the lack of information was a very severe limitation and said that at the present time his methodology probably did not provide a basis for breaking down the broad geological regions he considered into areas for further assessment."

Jan 1, 2014

"Chairman: Professor H. S. SICHEL Rapporteur: Miss M. I. WATSONPapers:Unrolling of Copperbelt orebodies by J. H. E. Perry and V. H. WiikAn exploration model for tabular orebodies by G. S. Koch and R. F. LinkHarmonic analysis of copper and gold occurrences in the Arbitibi area of the Canadian Shield by F. P. Agterberg and A. G. FabbriMathematical models of orebodies by M. J. Newton and A. G. Royle Estimation of lateritic-type orebodies by A. JournelIn his presentation Mr Wiik said that unrolling could be regarded as a reversal of the natural process of folding, so that the aim of an unrolling procedure would be the reconstruction of original pre-tectonic conditions. While simply formulated, this aim might not always be achieved. The geometrical relationship between points on the deformed surface and corresponding points on the original surface is process-dependent, and a true reconstruction could be achieved only if the deformation history were known in detail.In this computer unrolling procedure all these complexities were ignored. Referring to one particular marker horizon, Mr Wiik said that it was assumed in the procedure that this marker was deposited as a horizontal stratum and that it had subsequently been deformed by simple flexure-type folding.The procedure allowed the geologist to incorporate his knowledge and conception of the deposit through repeated re-contouring with dummy points. This 'manumatic' aspect of the procedure had proved invaluable, not only in resolving specific unrolling problems but also in making the system more acceptable to the geologists in general.Unrolling served towards removing what might be termed `tectonic noise' superimposed on the primary distribution patterns for regionalized variables such as metal content and orebody thickness. From this point of view, variograms derived on the basis of unrolled-plan co-ordinates should be more meaningful in terms of depositional environment than are variograms calculated from a normal map projection.Mr M. M. Oosterveld remarked that it appeared from the paper that there were problems in applying the unrolling technique to ore reserve calculation, and asked whether there were not other methods that might be used for that purpose.Mr Wiik replied that at present unrolling played only a minor role in practical ore reserve estimation within Roan Consolidated Mines, Limited. The techniques currently in use differed from one orebody to another, but in general they involved projection onto a vertical longitudinal section or a horizontal plan, with subsequent grid interpolation by means of a standard computer contouring package."

Jan 1, 2014

By J. J. Cilliers, I. K. Craig, J. D. le Roux, K. Hadler

An analysis of the state-observability characteristics of a dynamic tank-to-tank model of a flotation bank indicates that the concentrate-flow rate of each tank can be estimated from accurate measurements of the pulp height in each tank and the final tailings flow-rate exiting the final tank. Therefore, there is an opportunity to construct an observer (model-based soft-sensor) which can estimate the concentrate flow-rate of tanks in a flotation bank. The concentrate flow-rate, i.e. mass pull, is generally measured by means of froth image analysers on industrial plants. A model-based soft-sensor will not only provide a means to validate froth image analyser results, but could potentially substitute them as they are less expensive to implement and maintain. Keywords: Concentrate flow-rate, estimation, flotation, modelling, observability, soft-sensor

Jan 1, 2020

By D. M. C. Valbom

The introduction of new diamond sorting technologies as well as additional manufacturers I vendors, has increased the equipment selection and combinations available for recovery flowsheet design. This paper describes the methodology used and the benefits realized in the design of recovery plants by ensuring a fundamental understanding of the advantages and limitations of the technology embodied in the equipment, a comprehensive knowledge of the ore body characteristics, and the effective matching of this information in combination with operational commercial requirements.

Jan 1, 2010

By M. R. MacIver, M. Pawlik, H. Alizadeh

Treatment of tailings is an integral component of mineral processing. Tailings with a high clay content are a challenge for the mineral processing industry; e.g. the clay slimes produced from production of phosphate in the mid-western United States and the fine tailings produced from oil sands production in western Canada. Dispersants are a commonly used process aid, but their impact on the structure and settling properties of high clay content tailings is not well understood. The paper describes the changes in composition and bitumen release that occur when mature fine tailings (MFT) are treated with a polymeric dispersant (lignosulfonate.) Synchrotron-source computed tomography (CT) was used to obtain high-resolution 3D images of samples prepared at varying dosages of dispersant. The CT method permits a powerful visualisation of the internal structure and composition of the samples. These insights will enhance our understanding of the structural characteristics of mineral tailings relevant to solid-liquid separation by flocculation and thickening. Keywords: Dewatering, dispersion, dispersants, chemical treatment, computed tomography

Jan 1, 2020

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020

By А. Klemyatov, T. Vologdina, U. Gordeeva, S. Zbinets, А. Kalugin, N. Rozhdestvenskiy

The plants integrated in the PhosAgro group of companies perform processes from scientific research to the project, from ore mining to shipment of fertilisers and feed additives to consumers. An extensive process chain maintains smooth interaction at all stages from research to production. As an example, the paper shows the revamp of two beneficiation plants (ANOF-2 and ANOF-3), requiring a comprehensive approach to task solving. The intention of the revamp was to increase the total yield of apatite and nepheline concentrate, taking into account the gradual decline in the quality of ore being processed and ensuring the yield stability of final products during re-equipment of the plants. At ANOF-3, the crushing and grinding cycle was modernised, the production of nepheline concentrate was implemented, and the capacity of apatite flotation, dehydration, and drying was increased. At ANOF-2 a new process chain was implemented for the production of apatite concentrate in workshops previously used for the production of nepheline concentrate. The main building was withdrawn from operation, where ore grinding, apatite flotation and apatite concentrate thickening had been carried out. The total increase in apatite concentrate yield at two beneficiation plants was 1.3 times. A further increase in concentrate production is planned. Keywords: Apatite, nepheline, fertilisers, beneficiation, flotation, column flotation machines, revamp, fine screening

Jan 1, 2020

By T. S. Kagogo

The factors affecting haul truck tyre performance and the effectiveness of the management system at Rossing Uranium Mine were investigated with the aim of increasing tyre performance in terms of running hours until failure. The main objectives were to identify the types of tyre failure, their causes and cost implications, and evaluate the effectiveness of the management system. A site severity survey, weight study, and TKPH studies were conducted to determine the pit conditions, and an analysis of failed tyres carried out. The results showed that tyre performance at the mine has declined from 2009 to date, and the increase in lost value amounted to R5.7 million in 2012 alone. The main cause of tyre failure is loose rocks in the pit. The present management system in the load and haul department is not effective enough due to operational constraints it is facing.

Jan 1, 2014

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

By K. Forsberg, Ş. Kaya, C. Dittrich, M. Svärd, E. M. Peters

Scandium can be recovered from waste streams of other metallurgical processes such as red mud from the Bayer process and titanium dioxide acid waste. This is accomplished by an integrated process comprising leaching using acidic media, solvent extraction using organic solvents and stripping of Sc from the organic phase using NH4F solutions. The precipitation of scandium as (NH4)3ScF6 from NH4F strip liquors has been demonstrated at lab-scale with recoveries and purities greater than 98% and 98.3%, respectively. It is desired to assess the possibility of recovering the solvents for re-use in the process to improve its economy and environmental friendliness. Investigations have been conducted to recover alcohol by simple distillation from strip liquor-alcohol mixtures containing about 50 v/v% alcohol. The mixtures were obtained after anti-solvent precipitation of (NH4)3ScF6 using an alcohol to strip liquor volumetric ratio of 1:1. The starting strip liquor contained about 2000 mg/L scandium in 3 mol/L NH4F solution. In the recovery of methanol, the first distillate product collected had a purity of about 87 v/v% and this decreased slightly with time over two hours. The methanol distillate collected in the first 30 minutes with a purity of ca. 85 v/v% was re-used in anti-solvent crystallisation of (NH4)3ScF6 from the initial strip liquor, and the scandium recovery attained was about 98.6 w/w%, almost similar to that of 99.2 w/w% obtained using 100 v/v% methanol. For ethanol recovery, the first distillate product collected was approx. 84 v/v% pure and the distillate collected in the first 30 minutes with a purity of about 75 v/v% achieved a scandium recovery of about 97.2 w/w% in comparison to 98.5 w/w% obtained using 100 v/v% ethanol during anti-solvent crystallisation. Keywords: Alcohol recovery, methanol, ethanol, anti-solvent crystallisation, (NH4)3ScF6

Jan 1, 2020

By J. E. Dickinson, J. L. Sutherland, J. Zhou, M. J. Cole, K. P. Galvin

Interest in early gangue rejection has grown substantially in the minerals industry to reduce energy and water consumption arising from excessive comminution. Recent developments in coarse-particle flotation have proven successful by promoting a quiescent hydrodynamic environment to limit particlebubble detachment and by helping to convey more buoyant particles to the overflow. Current approaches also benefit from upstream classification to remove the finer particles ahead of the coarse-particle flotation. In this study, coarse-particle flotation was investigated experimentally using a novel hybrid gravity-flotation system called CoarseAIR™ that exploits the hydrodynamic advantages of the Reflux® Classifier. The system consists of a lower fluidised bed housing, with a system of inclined channels above. The inclined channels enhance the segregation and hence rejection of intermediate through to relatively coarse particles containing little or no surface liberation. This approach overcomes the need for pre-classification, while offering strong transport of coarse particles made buoyant through their attachment to air bubbles. The paper explores the strong relationship between the solids transport to the overflow and the input gas flux, showing firstly the potential for significant mass rejection at the relatively low gas fluxes, and robust performance in terms of recovery across the full range of gas fluxes. Keywords: Flotation, inclined channels, coarse particle flotation, Reflux Classifier

Jan 1, 2020

By H. Vuthaluru, O. Kavianipour, C. -Z. Li, N. Suresh, D. Sahu

The paper describes a CFD model developed for 76mm Dense Medium Cyclone (DMC) using Ansys Fluent Software to gain insights into the separation of particles according to their size and density. The simulation used in this paper includes the Reynolds stress model to predict the turbulence inside the cyclone body. An Eulerian-Eulerian multiphase CFD model was applied to model a number of physical aspects such as the separation of coal particles and the segregation of magnetite media solids. The experimental results generated in a laboratory scale DMC were used for the validation purpose and the predicted results of CFD have been validated for the flow splits of water, magnetite and coal. The simulation results obtained from the Eulerian-Eulerian multiphase model revealed that the prediction agreed with experimental results, and matched reasonably well in terms of the mass flow rates of water, magnetite and coal. Furthermore, the partition curve of the DMC when mapped for the separation of - 3.0+0.50 mm size also showed to be in agreement with the experimentally obtained curves. The gravity of cut (SG50), also predicted by the Eulerian-Eulerain multiphase CFD model, was found to be in the vicinity of observed experimental value of SG50. Keywords: Dense medium cyclone, Eulerian-Eulerain multi-phase modelling, computational fluid dynamics, cut gravity (SG50)

Jan 1, 2020

By L. A. Cisternas, A. Lopez-Valdivieso, Y. L. Botero, L. Cortes

In the processing of sulfidic ores, pyrite is usually depressed and ends up in the tailings. However, pyrite is the most common species responsible for acid mine drainage (AMD) due to its spontaneous oxidation. This AMD affects the tailing chemical stability by dissolving some toxic or heavy metals species such as As, Cd, Co, Pb, and Zn, which can migrate into the surrounding ecosystems. Therefore, the strategies to reduce pyrite’s environmental impacts are a crucial point to produce more chemically stable tailings. Consequently, numerous studies have been made to find procedures that could inhibit or restrain AMD. This work aims to develop a procedure for designing conceptual flotation circuits that can produce tailings with low content of pyrite and to assess this type of circuit with traditional flotation circuits. The method consists of applying optimal flotation design where three products are considered: metal concentrate, pyrite concentrate, and tailing with low content of pyrite. Two approaches are considered; in the first, a flotation circuit is designed to generate a concentrate rich in all sulfide minerals and to obtain a tail with low pyrite content. Then, a second flotation circuit is designed for the selective separation of the bulk into metal concentrate and pyrite concentrate. This is called fractional separation design. In the second approach, a flotation circuit design is realised that generate the three products simultaneously. This is called integrated separation design. Both fractional separation design and integrated separation design are assessed in this paper. This methodology is focused on cleaner production (waste prevention and resource minimisation) rather than end-of-pipe technology (treat existing waste). The methodology was applied to a copper sulfide ore from a local company in the Antofagasta region (Chile). This ore contains chalcocite, covellite, iron oxides, and pyrite. Keywords: Flotation, tailing, pyrite, cleaner production

Jan 1, 2020

By M. Krasowska, W. Skinner, R. K. Asamoah

Understanding chemical interactions at solid-liquid interfaces have played a pivotal role in improving mineral flotation performance, increasing the rate of mineral crystallisation and profitable leaching of valued minerals and metals. This paper highlights gold leaching with links to surface and interfacial chemical processes occurring, and opportunities to maximise extraction while reducing usage of more recent scarce resources. From the review, there is a significant link between surface and interfacial processes and gold leaching performance. Evidently, gold leaching kinetics could be increased by changing leaching conditions, including manipulating the surface and interfacial interactions. Control of surface and interfaces during gold extraction could enhance rapid, smarter gold extraction and mitigate formation of passivation layers. Keywords: Surface and interfaces, refractory ores and concentrates, gold leaching, reaction mechanism and kinetics

Jan 1, 2020