Search Documents

By E. A. Lauha

The Goldstrike Mine is in Eureka County, Nevada, U.S.A., approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora Mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike sub-district of the Carlin Trend, a northwest alignment of sediment hosted, disseminated gold deposits. The Carlin Trend includes over 15 major gold deposits with production, reserves and geological resources of approximately 65 million ounces of gold (Figure 1). In the Bluestar/Goldstrike sub-district, there are seven major deposits: Betze, Lower Post, Post, Genesis, Bluestar, Purple Vein and Deep Star, plus numerous smaller deposits (Figure 2). Production, reserves and resources for the sub-district are approximately 40 million ounces. Betze and Purple Vein are located on property controlled by Barrick Goldstrike Mines and Bluestar and Genesis on Newmont Gold property. Post, Lower Post and Deep Star occur both on Barrick and Newmont property.

Jan 1, 1993

By L. J. Habegger

This paper considers the potential water quality impacts of future energy scenarios which project an approximate doubling of coal utilization from 1975 to 1985. The major impacts estimated for coal extraction are related to effluents from unregulated activities (reclaimed areas prior to stable vegetation) and pollutants (e.g., metals and ammonia). Where applicable, the EPA effluent guidelines to be in effect by 1983 reduce the impact of individual sources to low levels. For example, total suspended solids and acidic discharges are to be regulated to levels generally below recommended water quality standards for receiving streams. However, implementation of these guidelines, particularly for coal extraction, has not been demonstrated on a wide scale. Water quality is not expected to be a major constraining factor for increasing capacity of coal fired utility and industrial boilers. Water quality control has not been demonstrated on a commercial scale for coal conversion to synfuels, but adequate control technologies appear to be feasible.

Jan 1, 1978

By J. A. Madonna

Universities and colleges in three countries -Australia, Canada and the United States, recognized the need to establish and reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral exploration companies and private consultants cooperated in the study by providing information regarding their specific training needs for support personnel, the data gathered has been used to identify training area for semi-skilled, skilled and technical personnel in geophysics, including, but not limited to, geo-logical skills, geophysical skills, surveying skills, environ-mental skills, and computer skills. With areas of major educational need defined for geophysical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will he discussed.

Jan 1, 1992

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By J. M. King, C. J. Boggs

Acquisitions of mineral properties and companies can saddle the acquirer with unexpected and substantial liabilities and obligations incurred by the acquired or selling company that are not readily apparent from review of the company's books or files. This paper will address selected areas of concern, such as environmental and reclamation liabilities, problems of foreign ownership by the buyer or seller, pension obligations, plant closing laws, effective title review, land use and zoning.

Jan 1, 1992

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By Richard Thomas Newcomb

The trend towards proportionately rising volumes of surface mining through- out the world and especially in the United States has led some observers to predict that the future of underground mining is quite limited. Certainly, the simple extrapolation of current trends1 gives evidence of a compelling sort for the hypothesis that technological progress is proceeding at a faster pace in surface than in underground mining. This paper attempts to examine the basis for these predictions by searching the historical record on differential rates of productivity as these are observed in iron ore and coal mining. In recent years economists have discussed "technology gaps" among industries or segments of the same industry, by which they mean that mechanisms for invention and its diffusion are faulty or retarded in such a way that feasible cost-cutting innovations are not applied or developed, even though technicians regard them as practical.2

Jan 1, 1968

By Gary N. Weinrich

Large surface mining projects in sparsely populated regions of the West have the potential to create disruptions in an area's social and economic character with potential effects on man that can far outweigh the physical and ecological effects on man's environment. The data and analyses involved in addressing the socioeconomic issues are additional to those traditionally associated with surface coal mining, such as those concerning land reclamation and water quality. Appropriate socioeconomic studies in conjunction with mine-planning can identify the potential problem areas in order that project measures can be taken to maximize the beneficial impacts and minimize the adverse effects of surface coal mining. The information required to conduct such socioeconomic analyses, available data sources, and the applicable analyses are described. Overall impacts of some proposed Western surface mines are summarized and potential mitigating steps discussed.

Jan 1, 1975

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By John D. Price

In the constant search for ways and means of improving the quality of coke and thus making its use at the blast-fornace more satisfactory and economical, it has become increasingly evident that the present laboratory tests do not show the full picture of a coke's value as a blast-furnace fuel. This fact was recognized by Dr. A. C. Pieldner thirty-five years ago: (Ref. 1) here is perhaps no phase of fuel technicology which has aroused more discussion or regarding which there is more difference of opinion than the properties of coke which make it most suitable for blast-furnaces and other uses." Dr. Fieldner followed this assertion with a statement to the effect that men who write on this subject today (1923) have, because of conflicting experimental evidence brought forth in recent years, far less positive opinions on the matter than did writers of some years past. One is led to wonder if these statements are not just as true now as they were when first made.

Jan 1, 1959

By Patrick R. Taylor

United States Antimony Corporation, at its Yankee Fork property in central Idaho, is currently using a combination of flotation, gravity-amalgamation, and concentrate cyanide leaching, silver sulfide precipitation, and activated charcoal loading to recover both silver and gold. Tine processes of flotation, milling, gravity concentration, amalgamation, concentrate leaching, sulfide precipitation and gold recovery via charcoal are discussed. The flow sheet illustrates the use of cyanidation as an alternative to shipment to a smelter.

Jan 1, 1984

By G. H. Lewis

This work was completed in a 440 KW pilot-scale combustor in preparation for a 50,000 Kg/hr industrial steam boiler limestone injection test program. The main objectives of the work were to: (1) identify the variables which affect sulfur capture, (2) determine the maximum sulfur removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. The variables which were identified as being important in sulfur capture were: Ca/S molar ratio, flue gas temperature at the limestone injection location, and limestone particle residence time. The maximum sulfur dioxide removal was 72%. The addition of limestone increased the particle deposition rate in the combustor; however, all deposits were easily removed by an air lance.

Jan 1, 1985

By German Zambrana

The solution of the problem of beneficiation of cassiterite from its primary ore deposits is of fundamental importance to Bolivia. The process today involves a gravimetric treatment of the ore followed by sulphide flotation. During the last year, a cassiterite flotation stage has been added in several plants to treat the slime tailings. Although cassiterite flotation is already economical for the slime tailings and the mechanism of the process are understood, it is felt that further research could improve the results. In the past, considerable amount of research and test ark has been performed to select appropriate collectors to improve recovery, to increa¬se the grade of tin in the concentrate, to minimize the effect of metallic ions like Ca+2, Fe+2 and Fe+3 which prevent flotation, and to increase the pH of the pulp which now it can not be higher than 3.0. It has been reported that the halogen salts (1) like NaCl exhibit special surface affinity for cassiterite but none for quartz. These effect seems to be favourable for the selective flotation of cassiterite from silica minerals. In view of these preliminary results it was decided to follow the research accordingly: OBJECTIVES The objectives of the present investigation are: 1. 0 evaluate the influence of NaCl salts in quartz and cassiterite flotation.

Jan 1, 1971

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By H. Sevim

This paper identifies and formulates the probabilistic nature of underground coal face operations using the Semi-Markovian theory. Through this theory the probability of coal flow from a face is obtained for any given time t of a shift. These probabilities are used for determining the capacity and operating policy of a surge tank located at the shaft bottom.

Jan 1, 1984

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978

By Keenan. Albert M

The challenge of mining coal seams having a pitch of 30 degrees is one not frequently found in the United States, due primarily to the scarcity of such deposits. However, in the Thompson Creek District in Pitkin, Colorado, such a challenge exists to produce high quality medium volatile coking coal, and development of a longwall system is underway. The deposits under consideration are those of the Anschutz Corporation Inc. of Denver, Colorado, which are not in a virgin state. The properties were originally mined by the Colorado Fuel and Iron Corporation from 1894-1907, and by the Thompson Creek Coal and Coke Corp. from 1953-1966. Approximately five and one half million tons of coal have been mined by the above companies, attesting to its quality. The cessation of operations in both instances was occasioned by economics. Both companies employed a room and pillar system of mining, but being denied the use of high capacity mining and loading machinery because of the excessive pitch of the coal seam. This resulted in an unfavorable productivity expressed as output per man-shift, and thus the high cost of production occasioned by hand loading and semi-mechanization dictated cessation of operations. The specific location of these deposits are in Pitkin County,

Jan 1, 1971