Search Documents

By R. V. Ramani, R. Srikanth, R. Zhao

A two-part study was conducted to understand the factors affecting respirable dust generation potential or dustiness of coal seams. In the first part, the data from three prior comprehensive laboratory studies was analyzed to establish quantitative relationships between respirable dust generation potential and coal characteristics. This analysis indicates that respirable dust generation rate is positively correlated with Hardgrove Grindability Index (HGI), fuel ratio (fixed carbodvolatile matter), Vitrinke Reflectance (VR), and Level of Organic Metamorphism (LOM). In the second part, specially-designed single breakage experiments were conducted to determine the primary dust generation potential of 17 coal samples obtained from four continuous miner sections, three longwall sections, and the Penn State Coal Data Bank. The single breakage study indicates that primary dust generation rate is positively correlated with fixed carbon content, fuel ratio (fixed carbon/volatile matter), VR, and LOM. Since VR and LOM are strongly influenced by the process of coalification, differences in respirable dust generation rates in different coal seams may be explained by the thermal metamorphism of sedimentary organic matter during subsurface burial.

Jan 1, 1995

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By S. Mathur

The southern Florida phosphate deposits that will be mined in the future contain significant amounts of dolomite. Because high MgO levels are undesirable in phosphoric acid production, several flotation schemes for the removal of the dolomite have been attempted. Alternatively, selective flocculation has been suggested as a potential process. A high MgO rock was simulated with a 30:10:60 mixture of apatite, dolomite and silica, respectively. Single mineral selectivity was observed in the apatite-silica and dolomite- silica systems using Polyacrylic acid (PAA) and Poly(ethylene oxide) (PEO) flocculants, respectively. However, no single mineral selectivity was observed in the apatite-dolomite system using PEO. Heteroflocculation, suspected to be the major reason for the loss of selectivity, was minimized by the addition of a site blocking agent (SBA), consisting of a lower- molecular-weight fraction of PEO. Process parameters such as size reduction schemes, flocculant/SBA dosage and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed-mineral tests was also achieved in the ternary mixed-mineral system, namely, the apatite-dolomite-silica system. In this report, surface chemical characterization of the samples and their flocculation behavior are discussed.

Jan 1, 1995

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices that minimize soil compaction will produce better results when forestland is the intended postmining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees. Since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree-survival rate. It is believed that these two soil-compaction parameters may ultimately be used to predict tree-survival rates on reclaimed surface mined lands.

Jan 1, 2003

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989

By Ian M. Loomis, Malcolm J. McPherson

A fuel-rich fire exists when the quantity of fuel exceeds the oxygen available to support complete combustion. The transition of a mine fire from Oxygen- rich to Fuel-rich combustion, at this time, represents a point-of-no-return in the fire fighting efforts. Once the transition has been made to fuel-rich the fire can spread at a rate 6 to 10 times as fast as in the oxygen-rich state. Utilizing available technology the fire fighters are left to seal the fuel-rich fie as the only technique to extinguish it. In order to minimize the devastating effects of a fuel- rich fire it is important to understand the means by which the fire becomes fuel-rich and by what means the fire may be returned to an oxygen-rich state. This paper covers: the development mechanism of a fuel- rich fire in a coal mine entry and the physical and chemical effects of applying water to a fire. Experiments concerning these matters have been conducted in a 30 cm square wind tunnel constructed at the Virginia Polytechnic Institute and State University as a model coal mine entry. This paper also addresses the results obtained in testing application of a water mist to fuel-rich fires in this model. These tests have centered on the development profile of a fuel-rich fire in a duct and demonstrate a means of regaining control of a fuel-rich fire by returning it to an oxygen-rich state.

Jan 1, 1995

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By J. A. McKeown, B. M. Sanders, A. Dadgar, R. H. Sergent

This paper describes the leaching of gold with Geobrom® 3400 from a very rich (6.2 kg/tonne) black sand concentrate and its subsequent recovery by ion exchange resins and solvent extraction. The dissolution of gold from black sand ranged from 94 to 96%. Gold loadings and recoveries of nearly 100% were achieved by both ion exchange and solvent extraction methods. The kinetics and equilibrium of loading gold onto ion exchange resins and its elution from the resin were studied. The commercial ion exchange resins PAZ®- 4, DOVEX®- 21K, and Amberlite® XAD- 7, and Great Lakes Chemical experimental GLR-30 were evaluated in this work. Diethylene glycol dibutyl ether was used in all the solvent extraction work for gold recovery from Geobrom leach solution. The consumption of Geobrom was about 130 kg per tonne of the concentrate processed. Therefore, the cost of lixiviant to extract 3.11 x l0-2 kg of gold from the black sand was only about $1.00. Based on the electrochemical regeneration of bromine, the economics of bromine process vs. cyanidation were investigated.

Jan 1, 1990

By Robert Snow, Yingxue Yu, Howard Hanson, Patrick Zhang

One of the major current efforts by the Florida phosphate industry to reduce deep aquifer water consumption is to use 100% recycle water for flotation. This measure alone could save billions of gallons of deep well water annually. However, this also results in higher suspended solids (slimes) in flotation water, causing poor process performance particularly for amine flotation. Polymers could play a major role in allowing the industry to use high-turbidity recycle water for amine flotation without compromising its impact on the Florida economy. The enhancement of rougher flotation by polymers may also have potential. Most importantly, dramatic efficiency improvement may be realized by floating silica first. Adding polymer to flotation feed and/or water is perhaps the most economically viable way of reversing the Crago "double float" process, in order to reduce operating costs and increase phosphate recovery. This paper presents both laboratory and pilot flotation data showing the effect of different polymers on collector dosage and flotation recovery. There appeared to be an optimal range of polymer concentration beyond which the benefits do not offset the drop in phosphate recovery. The effect of poly mer is slime-level dependent. Pilot testing data show that the "Reverse Crago" process (floating silica first followed by phosphate flotation) can outperform the Crago process.

Jan 1, 1999

By H. Polat, B. Mohal, S. Chander

Several nonionic surfactants and one anionic surfactant were tested to enhance the flotation response of a low-rank coal. The nonionic surfactants included an ethoxylated octylphenol and several polypropylene-polyethylene block copolymers, and the anionic surfactant was a dioctyl sulfosuccinate. All of the surfactants improved the yield significantly, but the influence on grade was complex. To elucidate the mechanisms involved, separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents, a correlation between the emulsifying power of the surfactant and the flotation response was observed. An increase in the number of droplets produced was considered to he the main reason for increases in the yield. However, a small amount of surfactant adsorption on coal is essential to promote adhesion of oil droplets. When the surfactant was introduced into the flotation pulp prior to addition of dodecane, the benefits of the surfactant decreased significantly. The decrease was attributed to both a decrease in hydrophobicity of coal through increased surfactant adsorption and a decrease in the surfactant available for emulsification. When a surfactant dispersed in oil was used, the transfer of surfactant to the aqueous phase was minimal, and a considerable increase in yield was observed.

Jan 1, 1995

By D. Raicevic

The presence of residual uranium and other radionuclides in the uranium mill tailings are posing a continuous health concern to the surrounding environment. The slow generation of sulphuric acid from residual sulphide minerals is the cause of persistant dissolution and discharge of many metallic components of the tailings. The most effective long term solution to these problems would seem to be to produce chemically stable tailings. This paper describes two possible answers to the objective: (1) Removal of radionuclides and pyrite from tailings by mineral dressing techniques; some 60 - 68% of the residual uranium, 70 - 75% of the radium, 60 - 65% of the thorium and 95 - 98% of the pyrite have been rejected from the Elliot Lake tailings. The decontaminated tailings contained 0.003% uranium, 50 - 60 pCi/g radium226, 0.01% thorium and less than 0.1% sulphur as pyrite. (2) Preconcentration of radionuclides and pyrite by beneficiation from Elliot Lake ores prior to leaching; applying this approach about 97% of the uranium, 95% of the radium, 92% of the thorium and 98.5% of the sulphides were concentrated in a radionuclide and pyrite concentrates comprising 25% and 8% of the ore, respectively. The preconcentration tailings (waste) produced contained 0.004% uranium, 20 - 25 pCi/g radium226, 0.005% thorium and less than 0.1% sulphur as pyrite. Economic and environmental advantages of both approaches and the leaching of the concentrates are also discussed.

Jan 1, 1980

By R. A. Burns

Kaolin clay has a broad range of applications with the paper market representing the largest end-use. Calcined kaolin finds application in paper, paint and plastics primarily for its high brightness and light scattering ability. It is well known as an extender for TiO2. Meta-kaolin possesses a unique set of physical and chemical characteristics finding use in both traditional kaolin/calcined kaolin markets as well as other unique applications. This paper discusses the intricacies of manufacture and the key physical and chemical properties of meta-kaolin. Specific applications and the relationship of the physical/chemical properties to end-use performance are discussed.

Jan 1, 2002

By R. C. Bryan, D. B. Jamison

This paper describes a procedure for minimizing the operational costs associated with blending sodium in coal at a surface mine in the Powder River Basin. Mine site blending is performed by adjusting daily production rates for high- and low-sodium pits. These adjustments are designed to produce a consistent sodium value called the blending target. The mine&apos;s contractual limit for sodium is sufficiently close to the field average value that any decrease in the sodium blending target may result in an opportunity cost, if the number of potentially minable tons is reduced. Conversely, any increase in the blending target may result in a higher sampling cost if more information is required to keep the blend within contractual limits. Blending parameters were defined using a geostatistical block model of sodium content that was based on analyses of hundreds of in-pit sample holes. Variograms for these data were used to compute the marginal costs of opportunity and sampling for a series of hypothetical in-pit drilling patterns. These marginal costs provided a basis for selecting optimum values for key parameters such as the blending target, production variance and in-pit sampling density. The benefit of implementing these optimized parameter values is that operational costs of sodium blending will be minimized over the long-term. At the mine where this procedure was developed, each dollar spent to increase the sampling density to the optimum value was shown to generate a $10 savings in opportunity cost.

Jan 1, 1991

By D. L. Jones, S. Knoerr, J. Mansanti

The Buckhorn Mine in Nevada currently treats oxide ore using heap leach methods, but exploration has identified sulphide reserves which are refractory in nature. Preliminary testwork was conducted on the sulphide material to screen potential pre-cyanidation treatment methods. Processes evaluated included pressure oxidation, biological oxidation, nitric acid oxidation and roasting. An initial economic and process analysis of the results concluded that roasting was the only viable process, and only if the roaster off-gases were converted to soleable sulphuric acid. Further economic analysis indicated that roasting of the whole ore was more attractive than pre-concentrating by flotation, followed by roasting of the concentrate. These results were generalized to show that for high sulphur ore a roaster/acid plant combination is more attractive that either of the other options, ie. pressure leaching or bioleaching, provided the by-product acid is soleable.

Jan 1, 1990

By Y. Topkaya, Lloyd Petrie, Dianne Marozas, R. E. Johnson, Steven Paulson, J. H. Canterford, B. R. Palmer, R. B. Bhappu, Lorin Redden

This paper describes a fundamental approach to in situ leach mining (ISLM) lixiviant development which emphasizes leaching selectivity through detailed characterization of mineral-solution interfacial chemistry and post-leach geochemistry. This experimentation and modeling approach consists of: (1) petrographic identification of reactive ore and gangue minerals; (2) determination of leaching kinetics of individual minerals through batch leaching tests; (3) evaluation of bulk solution geochemistry through column leaching tests; and (4) ISLM simulation of element species transport and geochemistry through core leaching tests. Recent results confirm good leaching selectivity for manganese, but reveal post- leach precipitation and permeability loss during core leaching experiments.

Jan 1, 1993

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

By Young C. Kim

Determination of the minimum sampling requirements of the run-of-mine (ROM) coal is very important for the purpose of meeting contract specifications. It is also important for the purpose of meeting emission regulations at a coal-burning power plant, such as the one located at Homer City, Pa. The classical statistical sampling theory can be applied to this problem, if ROM coal samples are known to be spatially (or serially) uncorrelated. On the other hand, the estimation variance concept from the Matherson&apos;s geostatistics must be used, if the samples are spatially correlated. Conditional simulation technique combined with simulation of the existing mining method is used to determine under which circumstances ROM coal samples do not preserve the spatial correlation. Only after establishing the degree of correlation that exists among ROM samples, an optimal sampling scheme can be devised using either the classical statistics Or the geostatistics. The minimum required sample volume can then be calculated using the well-known Gy&apos;s formula. This paper describes the results of the above investigation using the Helen coal mine data of the Homer City Owners. Empirical guidelines for determining the degree of correlation are also provided for coal mine operators.

Jan 1, 1986

By Kenneth S. Johnson

High-purity gypsum of Permian age crops out in three major gypsum districts of western Oklahoma. The northwest and southwest districts have important reserves in the Blaine Formation, whereas reserves of the west-central district are in the Cloud Chief Formation. Gypsum beds of the Blaine Formation typically are 10 to 30 feet thick, 95 to 99 percent pure, and interbedded with shales that are 2 to 30 feet thick. The base of the Cloud Chief Formation consists of a massive bed of gypsum that typically is 20 to 100 feet thick and is 92 to 97 percent pure. Anhydrite is present in the sulfate beds, beneath 20 to 100 feet of overburden, at a number of places in all three districts. Total gypsum reserves in the three districts are estimated at 48 billion short tons. These reserves are well suited for open-pit mining or quarrying, because gypsum typically forms hills in the semiarid climate of western Oklahoma, and the gypsum layers are nearly flat lying, without folds or faults. Seven companies currently mine a total of 1.0 to 1.4 million tons of Oklahoma gypsum each year for wallboard, for plaster, as a retarder in portland cement, and as a soil conditioner.

Jan 1, 1978

By Andrew I. Hustrulid

The discrete element method has successfully been used to model the behavior of material flow in transfer stations. With position, velocity, and applied forces for every particle and boundary in the simulation available at increments of 10-5 seconds, the next critical step is the presentation of this data in a concise and beneficial form. This paper discusses several methods of presenting the data from discrete element simulations that are used to improve the performance of a transfer station. These measurements are also used as a learning tool to better understand and visualize how material transfers from one belt to the next.

Jan 1, 1998