Search Documents

By Mark Fernald, Christian O’Keefe, John Viega

"In this presentation, the SONARtrac™ technology platform will be described. CiDRA's proprietary clamp-on, passive sonar array-based flow meter technology performs two independent measurements – flow rate and fluid characterization. Firstly, the meter provides the volumetric flow rate of the mixture by measuring the speed at which naturally occurring turbulent structures convect with the flow past an axial array of sensors. Secondly, the meter uses similar sonar-based processing techniques and naturally occurring sound in the process fluid to measure entrained air levels. The result is a unique ability to measure the flow rate and entrained air level of most fluids – clean liquids, high solids content slurries, and liquids and slurries with entrained air.Also to be presented is the application of the sonar-based technology platform in a variety of oil sands processes, hydrotransport, and minerals beneficiation applications. In particular, difficult slurry flow measurement and control in the areas of comminution and flotation such as mill discharge, hydrocyclone feed/overflow, final concentrate, thickener discharge, and tailings will be discussed. In addition new real time maintenance free process measurement capability will be presented in the areas of entrained air in slurry, collection zone gas holdup (?g), and slurry velocity profiling. The operational advantages and value of these measurements, even in the presence of scale buildup, will be discussed.INTRODUCTIONFlow measurements in the mineral processing and oil sands industry suffer from the limitations placed by previously available flowmeters including the commonly used instruments such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. The desire or requirement to make a non-contact measurement that is accurate and robust, and can be performed on practically any type of fluid within practically any type of pipe has driven the creation of a new class of flowmeters. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition."

Jan 1, 2007

By G. Zhu

The straight Y-shaped silica nanorods have been synthesized on Si wafer by thermal chemical evaporation of mixed powders of silica and graphite at 1300_ and condensation on Si substrate without assistance of any catalyst. The synthesized samples were characterized by means of scanning electron microscopy, transmission electron microscopy. The results suggested that the straight Y-shaped silica nanorods have uniform diameter about 50-200nm and neat smooth surface. The growth of such silica nanorods may be a result of the fluctuation of external conditions and internal structure faults causing a change in the growth direction of silica nanorods developed.

May 1, 2008

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

The geological features of the destructive plate margins of the southwest Pacific favour the formation of porphyry type deposits. The major controlling factor favouring the formation of gold-rich deposits of this type is a dense crust. This results in shallow intrusion of large magma bodies beneath andesite stratovolcanoes. Where the intrusives have near vertical sides, the comparatively low temperature of transfer of volatiles from the solidifying melt favours the partitioning of gold into bubbles of volatiles. They reduce the viscosity and density of the melt, resulting in the upward movement of a mineralised melt. With the drop of pressure with upward movement the bubbles separate into a two phase mixture, triggering freezing of the mineralised melt and the formation of a gold mineralised stockwork.

Jan 1, 1995

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Fábio de Oliveira Braga

Atualmente, tecidos de fibras sintéticas como a aramida (Kevlar®) e o polietileno (Dyneema®) têm sido os preferidos para proteção balística contra munições leves, e para integrar sistemas de proteção contra calibres superiores, como o 7,62 mm. Porém, por apelos econômicos, ambientais e da disponibilidade limitada destes produtos, materiais alternativos têm sido testados. Neste cenário, destacam-se os compósitos reforçados com fibras naturais, que têm demonstrado bom desempenho balístico. Assim, o objetivo deste trabalho é avaliar o desempenho individual de compósitos reforçados com fibras naturais de curauá, quando submetidos ao impacto balístico com munição 7,62 mm. Foram executados ensaios balísticos, medindo-se a energia do projétil absorvida pelos materais, e os resultados tratados estatisticamente por Anova e teste de Tukey. Mostrou-se que estes compósitos têm potencial para substituir as fibras sintéticas em sistemas de blindagem para proteção pessoal, com a vantagem de serem materiais leves, de baixo custo, nacionais, de ampla disponibilidade e ambientalmente corretos.

Aug 17, 2017

By R. S. Dean

"It has long been recognized that the properties of polycrystalline substances are not the same as those of single crystals. These differences are especially marked in metels and metallic minerals, and are of greatest practical importance in metal working and ore treatment. The property changes encountered in passing from a metal single crystal to a poly-crystalline aggregate are the same as are produced by cold-working a metal or by the precipitation of a disperse phase. Hence, we may logically assume that the property changes are all due directly or indirectly to the formation of interfacial area or internal surface. Our problem, then, is to ascertain the physicochemical state of the metal atoms at such internal surface and show how this physicochemical condition accounts for the pronounced changes of mechanical, magnetic, and electrical properties that accompany increased internal surface.GENERAL CONCEPT OF INTERNAL SURFACEIn 1678, Huyghens attempted to explain the double refraction of calcite by postulating that crystals were built from a regular arrangement of ellipsoidal particles. Over 100 years later, Abbé Hauy concluded from his studies of cleavage that crystals might be built from small units, but the units were of the same shape as the entire crystal. This idea, which was prevalent in mineralogical thought before the advent of X-ray spectrometry, was discarded when the great success of Bragg made it appear that the chemical atoms were in reality the elements of structure. In the further development of X-ray technique, however, C. G. Darwin, in England, and P. P. Ewald, in Germany, found it necessary to postulate crystal units con¬taining many atoms. The latter gave the name of mosaic crystals to those so constituted. The individual units are supposed to Possess the ideal atomic arrangements revealed by the X-ray but are not oriented with respect to one another."

May 1, 1938

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By Irvin G. Burough

ANDROS INCORPORATED has designed, manufactured and delivered four handheld C02 DETECTORS and three handheld CH4 DETECTORS. These instruments are for in-mine safety use. The DETECTORS incorporated an NDIR optical/electronic analyzer design in which exceptional zero stability is achieved by pressure modulation of the sample gas. This eliminates the need for daily calibration. This stability and the miniature design (2.5" x 4.5" x 4.5"; 4.5 lbs) of the C02/CH4 DETECTORS provide practical instruments suitable for routine safety inspections. This report includes the theory and design of the instruments as well as studies of gas-pressure modulation by a piezoceramic-driven Helmholtz resonator.

Jan 1, 1979

By J. L. SILSBEE

THE existence of large saline deposits in that flat arid basin, known as the Great Salt Lake Desert, has long been recognized, but the extent and great commercial value of these deposits has not been generally appreciated. That a very considerable interest has recently developed is indicated by the fact that about 263 prospecting permits-each covering about 2560 acres of land in this Desert-have been issued under the Potash Leasing Act (Act of 0ct. 2, 1917-40 Stat. 297), and patents granted on approximately 40,000 acres. It is reported that patents and leases have, or will be applied for on an additional 80,000 acres in the basin. , Tests have been made on probably less than 10 per cent. of the total area of the basin, but these have proved a practically unlimited supply of brine available -sufficient, probably, to. furnish the potassium and magnesium chloride requirements of this country for at least a hundred years.

Jan 1, 1925

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

I once read an æarticleÆ in FHM Magazine entitled æThe Coolest Jobs There Ever WasÆ. It was about a group of guys who were pursuing careers that any person on the planet would just kill for. I distinctly remember drooling over the pages, thinking how much I would love to be Michael SchumacherÆs Chief Engineer at Ferrari, or the Principal Designer and Tester for one of the big Dutch rollercoaster companies. From that moment on, I decided that I wanted a career that was cool enough to make it into the pages of that article. Throughout my time at university, I always had that article in the back of my mind. As a result I constantly wondered about what sort of job I could end up with once I left university. More importantly, I wondered if FHM would be banging down my door to put me in the magazine! After a long and stressful job hunting process (in between completing a thesis and studying for exams) I finally managed to land myself a job with Orica Mining Services. I can honestly say I didnÆt know what to expect when I first joined Orica. Most of my friends ended up working for big mining companies, while I was offered a position with one of the biggest suppliers to these mining companies. However, I had a feeling when I was discussing the role with my future supervisor during the interview process that the job was going to be awesome. I have now spent a year working for Orica and I absolutely love it! While I feel that my job is worthy of being in that FHM article, unfortunately, I donÆt think I am going to get my opportunity to be in the magazine. Apparently I donÆt look too good in a bikini! However, I would love to have the opportunity to discuss the journey that I have taken so far û from my time as an environmental science graduate, then moving on to mining engineering, to now, being part of the Orica Mining Services Graduate Program. My suggestion is to use this paper as a resource. I have learnt during my time at university, as well as my time in the workforce, that the best people you can learn from are your peers. Take what you feel is relevant from the paper; hopefully it will help guide you in shaping your own career.

Jan 1, 2005

By Edmund Newton

This paper is one of a series comprising the Mineral Industries Survey of the United States, which was begun in 1935. It describes the simple methods of mining and beneficiating manganese ore, in eastern Tennessee and compares these methods with those used elsewhere in the Appalachian region. The report contains general information on manganese to give a clearer understanding of the methods and costs of mining and. beneficiating manganese ore foam a widespread deposit, an in addition presents zone difficulties normally fond in these operations. The marketing, uses, and value of manganese ore are discussed as well as the amount of capital necessary for effective operation on given scale of production, and requirements are outlines for successful operation of manganese, property in this region.

Jan 1, 1941

By Probert D. H, Wright E. A, Taylor B. L

A general description of the geology of the Southern Coalfield is given. The relationship between the Illawarra Coal Measures, the overlying Triassic and the underlying Upper Marine Series, of Permian age as are the Coal Measures, is briefly explained and thestratigraphy of each is described. The eight coal seams are then treated in slightly more detail as to their thickness, quality, areas of distribution and best occurrences.In the last few years each of the authors has been concerned with one phase or other of the stTucture of the field in detail or in mining operations with the result that it is now possible to name a number of monoclines, anticlines, domes and synclines defined in detail. A minor quantitative study has been made of faults and dykes with regard to form, direction intensity and inter-relationship. It seems probable that with the further collection of data a more detailed study in these matters will be of considerable value to the economy of mining in the Southern Coalfield.

Jan 1, 1958

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By Brett Campbell

The San Vicente to 2nd Aqueduct Pipeline?Tunnel project is a raw water conveyance tunnel linking the San Vicente Reservoir (SVR) to the 2nd Aqueduct Pipeline via Rancho Penasquitos Pressure Control Facility (RPPCF). This 58,230 lf long tunnel will be 8.5? final ID, and has four points of construction access. The job is classified into 6 Reaches of tunnel, identified by the dominant geology within the reach. This paper will focus on Reach 3, specifically the measures necessary to drill and blast a 550 lineal foot section of granitic rock tunnel immediately in front of an open face digger shield.

Jan 1, 2008