Search Documents

The projection of operating costs for mining, processing, and other site operating costs is an exercise which can be fraught with considerable peril. Not only are the physical characteristics of each mineral property unique, but a range of other factors will influence the consultant's approach to compiling cash flow estimates. This paper details some of the techniques used in estimating operating costs for use in order-of-magnitude cost studies and feasibility studies, and describes how to avoid common areas of difficulty. A series of examples relating to open pit gold mining and processing cost estimates illustrate these problems, and various corrective methods are described. The mining and treatment processes, and their associated cost elements, are followed in sequence of operation from on-going ore delineation through to disposal of the product. In addition the problem of assigning management, administration and overhead costs along with taxation allowances is addressed. Of critical importance is the application or possible misapplication of accrual procedures to the cost elements. In many cases such misapplication can introduce more pronounced errors with projects of short duration, such as the typical open pit/C.I.P. gold operation commenced in the last decade. The importance of providing verification of estimates depending upon the standard of the cost study is also investigated, and opinion is provided upon the minimum levels of verification necessary at various stages. Finally, the amalgamation of the various individual cost elements into a coherent whole is reviewed.

Jan 1, 1990

By Jan A. Nilsen

This paper describes a key element in the construction of a major project undertaken by Harbourfront Corporation in its efforts to rejuvenate the central Toronto waterfront. The Spadina Pier forms one of the two major structures of the $10 million marina complex. Completed in early 1986, the 150 metre(490 ft.) long by 43 metre(140 ft.) wide pier structure will contain a 320 car parking garage as well as providing the foundation of a 17-story residential tower and a two-story retail/commercial complex. However, the pier structure posed a considerable challenge to its developers due to the the many restrictions imposed on the site by the environmental authorities which ruled out the construction of dykes or the placing of other fill materials on the highly contaminated bottom sediments. In addition, access at the site was restricted by its proximity to the main harbour navigation channel and a grain elevator berth. The original design called for a cofferdam to form an integral part of the finished structure. However, the contractor chose to regard the cofferdam as a temporary structure and proposed to construct the pier in the dry by enclosing the 10,000 square metre(107,600 sf) site with a 450 metre(1480 ft.) long single wall steel sheet pile cofferdom 7.5 metres(25 ft.) from the final pier structure. This paper will describes the design and construction of the cofferdam. Prior to finalizing the pier design, a geotechnical investigation of the shale bedrock was undertaken as well as a small sheet pile test cell program to evaluate the feasibility of driving a Canadian manufactured cold-rolled sheet pile into the bedrock. Relying on the design parameters for the shale bedrock, Foundation designed the cofferdam utilizing a post-tensioned bipod bracing system to resist a 7 metre(23 ft.) hydrostatic head as well as the maximum wind and wave forces expected at the site. The bipod bracing system consists of diagonal H-pile raker piles and verticle pipe piles anchored to bedrock with post-tensioned anchors grouted into bedrock.

Jan 1, 1987

Mr Kapp's paper helps considerably to clarify the subsidence/mine geometry relationships in New South Wales. It is in the best tradition of the presentation of field investigations such as has built up internationalknowledge over the years.The Author has plotted in Fig. 10, the maximum subsidence developed over each of a number of panels of different width/depth ratios and concludes that the maximum possible subsidence over a super critical extractionarea is around 0.65 of the mining height and that this is reached with the critical width/depth ratio of extraction of around 1.5.Although, as Mr. Kapp says, the maximum possible subsidence in the UK can reach 90% of the seam thickness extracted the more usual figure for the first seam is up to 80%. It has also been found in the UK that with shallow workings such as those at Kemiro Coliery the critical width of extraction is 2.0 or more times the depth.

Jan 1, 1981

By Mike Dry, Rod Dry

If humanity is truly serious about reducing emissions of carbon dioxide into the atmosphere, today’s power plants burning fossil fuels will have to be replaced by power plants that do not emit CO₂. Unless carbon capture/sequestration becomes practical, the new power plants will be hydroelectric, wind, solar or nuclear installations. Hydroelectricity requires the appropriate geography. Solar installations can only deliver power as and when sunshine is available, and wind installations when the wind blows. Therefore, power from these sources will be intermittent, but the demand for electricity does not follow the patterns of sun and wind. That will require large-scale electricity storage and/or load following by the remaining power suppliers, increasingly so as the use of fossil fuelled power generation declines. Modern nuclear power plants are designed for demand following. However, operating at lower than design output has a negative impact on the economics of nuclear power plants because the overall cost of the electricity they generate is dominated by capital cost. Primary (blast furnace) iron smelting is responsible for a significant part of global CO₂ emissions because the reagent used is carbon. Were it available in sufficient quantity (and at a low enough cost), hydrogen could replace carbon in the manufacture of raw direct reduced iron (DRI), using technology such as modified HYL (Tenova Hyl, 2018) or Midrex (Ravenscroft, 2017). This paper examines a scenario in which, instead of demand following, nuclear power stations are operated at their design capacities and surplus power is used to generate hydrogen in off-peak periods. This hydrogen is then used to replace carbon in the manufacture of raw steel.

Jan 1, 2020

By H. Q. Peng

The study of synergistic reagents combination of mineral floatation is more and more important with the decreasing of bonanzas now. In order to determine the chemical reaction mechanism, here we present the synergistic reagents combination: amyl-xanthate, butyl-dithiophosphate and N,N-diethyldithiocarbamate ester, which dissolved by different organic solvents. The reagents were applied by an Anhui mine to float low-grade covellite as a substitute for ethyl-xanthate. One reaction products Na2HPSO3?5H2O (disodium hydrogen-thiophosphate pentahydrate) which was re-crystalized and measured by X-ray diffraction analysis. In its crystal structure, the two crystallo-graphically different Na ions are six-coordinated and are bridged by two covalent bonds with the O atoms of water molecules to give a basket unit. However, we can?t get Na2HPSO3?5 H2O by combining butyl-dithiophosphate and N,N-diethyldithiocarbamate ester under the same condition. This discovery may provides a intuitionistic evidence that in the process of reaction, the three com-pounds would cooperate with each other, but the decisive reaction may be the hydrolyzation of amyl-xanthate.

Jan 1, 2014

By Francisco Alberto Marreiros da Rocha Filho

No processo de laminação a quente ocorre ocasionalmente a perda de ductilidade a quente que pode causar o fenômeno denominado como “abertura de cabeça” da barra durante a sequência de passes. Essa perda de ductilidade a quente pode ser severa e causar interrupções no processo produtivo. Esse fenômeno pode estar associado a diversos fatores entre eles: composição química do aço; defeitos presentes no tarugo; condições do processo de laminação; e temperatura do aço durante o processo, principalmente nos passes de desbaste e intermediários de laminação. No processo em estudo, a perda de ductilidade a quente ocorre associada à laminação de vergalhões a partir de tarugos oriundos diretamente do lingotamento contínuo. O presente trabalho tem como objetivo avaliar a influência da temperatura e da microestrutura formada ao longo do processo na perda de ductilidade a quente das barras através de um exame comparativo entre os vergalhões laminados com e sem o uso da etapa de reaquecimento.

Oct 30, 2017

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk. Keywords platinum, mining, community, socio-economic impact, stakeholders, conflict, labour unrest, social licence to operate, investment, Africa.

Mar 1, 2013

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By Otaviano Donizeti Valadão de Freitas

Ruídos elétricos afetam os circuitos lógicos e conseqüentemente podem comprometer a confiabilidade nos controles de processos, e para minimizar as influências desses ruídos, algumas medidas básicas foram tomadas, com instalações adequadas de todo o sistema, como padronização do aterramento, encaminhamento de cabos, etc. Depois que as medidas foram implementadas, o resultado foi um sistema mais confiável. Se apenas um fio for encaminhado de forma incorreta ou se o aterramento estiver inadequado, pode ser suficiente para causar problemas. A experiência mostra que é muito difícil que todas as medidas sejam aplicadas integralmente, mas se não forem tomadas pelo menos as medidas básicas, o sistema ficará suscetível.

Sep 25, 2017

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InAs and GaAs were measured over the temperature range 400°K to temperatures above the melting points using a di-phenyl ether drop calorimeter. Smoothed values of the thermal properties have been derived and tabulated at even temperature interuals . The heats of fusion of InAs and GaAs were determined as, respectively, 8790 ± 200 and 12,590 ± 300 cal per g-atom at the respective melting points of 1210º ± and 1513º ± 1°K, yielding entropies of fusion of 7.26 * 0.16 and 8.32 ± 0.20 cal perºK per g-atom, respectively. A general discussion of the thermal properties of III-V com-pounds is given. THE low-temperature heat capacities of InAs and GaAs have been determined by Piesbergen.1Using a dynamic temperature modulation technique, Miller2 has determined the heat capacities of the compounds as well as GaSb and Ge between room temperature and 650°K; however, it has been observed that values determined by drop calorimetry for GaSb3 and for germanium4 are consistently about 5 pct lower than Miller's results. Cox and Pool10 report values for the heat content of InAs and GaAs and the heat of fusion of InAs. No value for the heat of fusion of GaAs appears to have been previously reported. This paper reports results of high-temperature heat content investigations of InAs and GaAs measured in the range 400" to above 1500°K employing a diphenyl ether drop calorimeter. These results, together with our previous results on III-Sb compounds3 as well as heat-content measurements5 of solid InP and Gap, are used in a general discussion of these compounds. EXPERIMENTAL PROCEDURES High-purity samples of the compounds, stoichio-metric to ±0.1 at. pct, were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories. The sample preparation, description of the calorimeter, and details of the heat content measurement have been previously described.3 Samples were sealed in evacuated silica capsules and suspended by a Pt-Rh wire in a Pt-wound vertical tube furnace, heated to temperature

Jan 1, 1970

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By Bráulio Campagnaro Santana

Na indústria da mineração, a liga Fe-Cr-C destaca-se como um revestimento duro em chapas de desgaste objetivando aumentar a vida útil do ativo. Três ligas, duas delas contendo Fe-Cr-C, sendo uma com aproximadamente 28% (p) de Cr e outra com 38% (p) de Cr e uma terceira liga com 24% (p) de Cr e 7,0% (p) de Nb foram levadas a ensaios de desgaste abrasivo roda de borracha conforme norma ASTM G65-04, além de medições de dureza, microdureza e caracterizações microestruturais. Constatou-se que os revestimentos contendo Nb, depositados com uma ou duas camadas de solda, possuem maior resistência ao desgaste abrasivo, seguidos pelos com maior teor de Cr. Os revestimentos que possuem maior fração volumétrica de carbonetos, finamente distribuídos na matriz, apresentaram os melhores resultados na resistência ao desgaste. Analisando no microscópio confocal 3D os revestimentos contendo Cr, notou-se que os mecanismos de desgaste são do tipo microcorte e microssulcamento, enquanto naqueles contendo nióbio prevalece o desgaste por rolamento em boa parte da superfície. A liga contendo Nb apresenta o melhor desempenho na resistência ao desgaste abrasivo em relação às demais, e se torna viável economicamente sua aplicação na indústria.

Oct 30, 2017

By A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which bid no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton A coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By S. Banisi, M. Poorkani, M. Farzaneh, M. Askari

"At the Sarcheshmeh copper mine 40,000 t of ore per day with an average grade of 0.9 % Cu is ground to 70% passing 75 microns. Grinding is effected in 8 parallel lines of 8 x 5 m ball mills in a closed circuit with cyclones. The make-up balls are 80-mm forged alloy steel balls and the average ball consumption is 750 gh of ore ground. In order to optimize ball size distribution inside the mill, based on the previous investigation instead of using only 80 mm make-up balls a combination of 80 and 60 mm (75% to 25% by weight) ball charge was used in one of the mills. To evaluate the performance of three ball types namely forged alloy steel balls (A), ductile cast iron (C), high chromium cast iron (D) and also a combined (80 and 60 mm) charge of forged alloy steel balls (B), four identical parallel mills were charged accordingly. These four mills were sampled during a period of six months. The amount of material finer than 75 microns of cyclone overflows was selected as a criterion for the performance evaluation. It was observed that in a mill with the combined make-up balls the amount of fine produced was 4% higher than the other mills. The consumption of ball types A, C and D were 730, 710 and 534 g/t, respectively. The results of laboratory flotation tests showed that due to an improvement in the production of fines an increase of 1.4% in the overall copper recovery is obtainable. Due to the promising results, the new make-up ball regime was implemented in all mills in the plant.INTRODUCTIONThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and has been processing 40,000 t/d of ore since 1982. The mine produces 100,000 tonnes of copper and 2,200 tonnes of molybednite concentrate per year. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailing constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83 and 87 % depending on the operating conditions and ore type."

Jan 1, 2002

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

By J Parr, P Ashworth, S Johns, C Yeats, A Littleboy

The ocean floor is increasingly being discussed in terms of its resource potential. New discoveries, improved knowledge and access to unexplored areas of the deep sea and continental shelf are some factors contributing to a renewed interest in the seafloor exploration and mining industry. The industry has been referred to as the ænext minerals frontierÆ. To date, much of the research has focused on proving economic and technical viability of the industry, with environmental issues addressed locally. However, there is limited research internationally, and none known in Australia that considers the social viability of the industry, addressing issues such as regulatory contexts, international precedence and public acceptability. Does the nascent seafloor exploration and mining industry have a social license to operate? Does it have support amongst the wider community? If not, why not? The Wealth from Oceans National Research Flagship explored these questions by scoping the social issues that would surround an expansion. Two desktop studies provide insight into the current level of activity in seafloor exploration and mining, recent developments and the regulatory regimes on which the industry is based. One study focused on the situation in Australia, while the other was internationally focused. A series of workshops were held with key stakeholders from government agencies, industry and other interested parties, such as environmental groups and the fisheries industry. These workshops identified and explored the different stakeholdersÆ perceptions of the benefits, concerns, opportunities and key questions associated with an expansion of the seafloor mining industry. The desktop studies revealed that Australia is one of only a few countries with legislation specific to seafloor exploration and mining. Nevertheless, barriers to licence approval exist because of lack of precedent in applying this legislation. Consequently, the decision process can be vulnerable to political issues and subjective judgements. The outcomes from the stakeholder workshops suggest this inconsistency may be influenced by the high levels of concern and uncertainty over environmental impacts. Uncertainty over environmental impacts can influence the acceptability of an environmental impact assessment (EIA) and also mean the perception of risk is variable. Overall, this research suggests that the future of the seafloor exploration and mining industry will be highly dependent on AustraliaÆs ability to:improve the knowledge-base underpinning the regulatory regime,generate open and transparent communications between stakeholders, andimprove the understanding of policy and regulatory processes.

Jan 1, 2008

By Jackson R. Pressley, Bruce Vandenberg

An explosive’s velocity of detonation, (VOD), can be used to indicate a number of important characteristics regarding the product’s performance, under specific field and test conditions.

Jan 1, 1997